Microstructure and corrosion resistance of Fe/Mo composite amorphous coatings prepared by air plasma spraying

Fe/Mo composite coatings were prepared by air plasma spraying (APS) using Fe-based and Mo-based amorphous and nanocrystalline mixed powders. Microstructural studies show that the composite coatings present a layered structure with low porosity due to adding the self-bonded Mo-based alloy. Corrosion behaviors of the composite coatings, the Fe-based coatings and the Mo-based coatings were investigated by electrochemical measurements and salt spray tests. Electrochemical results show that the composite coatings exhibit a lower polarization current density and higher corrosion potentials than the Fe-based coating when tested in 3.5wt% NaCl solutions, indicating superior corrosion resistance compared with the Fe-based coating. Also with the increase in addition of the Mo-based alloy, a raised corrosion resistance, inferred by an increase in corrosion potential and a decrease in polarization current density, can be found. The results of salt spray tests again show that the corrosion resistance is enhanced by adding the Mo-based alloy, which helps to reduce the porosity of the composite coatings and enhance the stability of the passive films.     

Influence of laser scanning speed on Cu-Zr-Al composite coatings on Mg alloys

To improve the surface properties of magnesium alloys, a study was conducted on Cu-Zr-Al composite coatings on AZ91HP magnesium alloy by laser cladding. The influence of laser scanning speed on the microstructures and properties of the coatings was discussed. The coatings consist of amorphous phase, Cu8Zr3, and Cu10Zr7. With the increase of laser scanning speed, the amorphous phase content of the coatings increases and reaches 60.56wt% with the laser scanning speed of 2.0 m/min. Because of the influence of laser scanning speed on the amorphous and crystal phases, the coatings show the maximum elastic modulus, hardness, and wear resistance at the laser scanning speed of 1.0 m/min. At the laser scanning speed of 2.0 m/min, the coatings have the best corrosion resistance.     

钴对热浸镀锌层耐腐蚀性的影响

通过5 wt%NaCl溶液浸泡腐蚀实验和电化学极化实验测量了热浸锌镀层的腐蚀速率和极化曲线,采用光学显微镜、扫描电镜SEM观察了镀层腐蚀后表面的显微组织,初步探讨了腐蚀机理.研究结果表明:锌浴中加入钴的合金镀层抗腐蚀能力要强于纯锌浴镀层;在盐水腐蚀溶液中,锌镀层能够阻滞腐蚀保护基体的主要原因,是牺牲阳极锌和在镀层表面形成了一层由ZnO和ZnCl2.4Zn(OH)2组成的钝化膜;当锌浴中添加适量钴元素后,在镀层中会形成富钴层,可以阻碍镀层的腐蚀,也有利于稳定腐蚀初期生成的Zn(OH)2或ZnCl2.4Zn(OH)2,降低腐蚀电流,提高镀层的耐腐蚀性能.     

磷化/硅酸盐溶胶封闭复合膜的EIS腐蚀机理

采用电化学阻抗谱EIS测量研究了先磷化再硅酸盐溶胶封闭后处理的热镀锌钢在5%NaCl溶液中浸泡不同时间的腐蚀行为,建立了等效电路模型,分析了相关参数的变化规律,探讨了复合膜的腐蚀机理.结果表明:复合膜的耐蚀性随磷化时间的延长而增强,复合膜高电阻、低电容的特性是抑制基底锌层电极反应的关键;随着浸泡时间的延长,镀锌钢的耐蚀性指标变差,腐蚀初期主要发生复合膜的溶解破坏,腐蚀后期主要发生膜层下基体锌层的腐蚀反应.     

化学镀非晶态Ni-P及Ni-Sn-P镀层在弱酸性介质中耐蚀性研究

以紫铜为基体,采用化学镀制备了非晶态Ni-P,Ni-Sn-P镀层.采用X射线衍射(XRD)、扫描电子显微镜(SEM)和X射线能谱(EDS)等对镀层的结构、微观形貌及元素组成进行分析.通过Tafel极化曲线、电化学阻抗谱(EIS)、开路电位监测及室内加速腐蚀试验,研究两种镀层在pH=5.5,w_(NaCl)=3.5%,以及pH=5.5,wS=20%的土壤介质中的耐蚀性能.结果表明,化学镀非晶态Ni-P及Ni-Sn-P镀层的自腐蚀电流密度是裸铜的4.5%和1.2%,两种镀层在酸性腐蚀介质中具有比金属铜更好的耐蚀性,并且化学镀Ni-Sn-P镀层耐蚀性优于Ni-P镀层.两种镀层的自腐蚀电位均负于铜.     

Application of mesoporous silica nanocontainers as an intelligent host of molybdate corrosion inhibitor embedded in the epoxy coated steel

In this study, mesoporous silica served as a host for corrosion inhibitor. This material could adsorb and release corrosion inhibitor in different aqueous media. However, the extent of corrosion inhibitor release in the alkaline media was higher. By dispersing 1 wt% mesoporous silica loaded with sodium molybdate in the epoxy layer, a protective composite coating was produced. The corrosion properties of the composite coatings were assessed by electrochemical impedance spectroscopy. Results showed higher corrosion resistance of epoxy/mesoporous silica loaded with inhibitor in the NaCl media for eight weeks of immersion in comparison with epoxy/mesoporous silica. Corrosion inhibitors released from nano-containers in the response to corrosion damage at the interface zone.     

化学镀Ni-P-W／A12O3复合镀层的耐腐蚀性能研究

用化学镀方法在NdFeB磁性材料基体表面施镀Ni-P-W／A12O3复合镀层．用扫描电子显微镜和X射线仪分别对Ni-P-W／A1203复合镀层的组织形貌和相组成进行了分析,并用腐蚀失重法对复合镀层的耐腐蚀性能进行了测试．结果表明,随着Alzos质量含量（5-20g／L）的逐渐增大,Ni-P-W／A12O3复合镀层的抗腐蚀性能逐渐增强．     

Electrochemical behavior of different shelled microcapsule composite copper coatings

Copper/liquid microcapsule composite coatings with polyvinyl alcohol (PVA), gelatin or methyl cellulose (MC) as shell materials were prepared by electrodeposition. The influence of shell materials on the corrosion resistance of the composite coatings in 0.1 M H₂SO₄ was investigated by means of electrochemical techniques, scanning electron microscopy (SEM), and energy dispersion spectrometry (EDS). The results show that the participation of microcapsules can enhance the corrosion resistance of the composite coatings compared with the traditional copper layer. Based on the analysis of electrochemical test results, the release ways of microcapsules were deduced. Gelatin and MC as the shell materials of microcapsules are easy to release quickly in the composite coating. On the contrary, the releasing speed of PVA microcapsules is relatively slow due to their characteristics.     

Incorporation of nano/micron-SiC particles in Ni-based composite coatings towards enhanced mechanical and anti-corrosion properties

Ni-based composite coatings incorporated with nano/micron SiC particles were fabricated via electrochemical co-deposition in Watts bath,followed by the evaluation of their mechanical and anti-corrosion properties.The micrographic observations suggest that the SiC particles with various sizes can be well incorporated to the Ni substrate.X-ray diffraction(XRD)patterns indicate that SiC particles with smaller sizes could weaken the preferential growth of Ni along(200)facet.In addition,it is found that the incorporated SiC particles with medium micron sizes(8 and 1.5μm)could significantly enhance the micro-hardness of the Ni composite coatings.Nevertheless,electrochemical measurements demonstrate that micron-sized SiC particles would weaken the corrosion resistance of Ni composite coatings ascribed to the structure defects induced.In contrast,the combined incorporation of nanosized(50 nm)SiC particles with medium micron(1.5μm)ones is capable of promoting the compactness of the composite coatings,which is beneficial to the long-term corrosion resistance with negligible micro-hardness loss.     

磷化/钼酸盐后处理的热镀锌钢板的电化学行为

将热镀锌钢板先磷化再用钼酸盐溶液进行封闭后处理,通过塔菲尔极化和电化学阻抗测量研究其在5%NaCl水溶液中的腐蚀电化学行为,并与单磷化的热镀锌钢板进行了对比.结果表明:磷化的热镀锌钢板再经钼酸盐封闭处理后,阳极极化和阴极极化均明显增强,腐蚀保护效率显著提高,发挥了单磷化膜和单钼酸盐膜耐蚀性能的协同效应,电化学阻抗值提高了一个数量级以上;在5%NaCl水溶液中浸泡的初期,低频扩散阻抗值随浸泡时间延长而增大,表明复合膜具有一定的自修复能力.     

Microstructure and corrosion behavior of Al<Subscript>3</Subscript>Ti/ADC12 composite modified with Sr

In this study, we investigated the effect of the addition of Sr (0wt%, 0.1wt%, 0.2wt%, and 0.3wt%) on the microstructure and corrosion behavior of Al₃Ti/ADC12 composite by optical microscopy, X-ray diffraction, scanning electron microscopy, and energy diffraction spectroscopy. The results reveal that the α-Al phases were nearly spherical and 40 μm in size and that the eutectic Si phases became round in the composite when the Sr content reached 0.2wt%. The Al₃Ti particles were distributed uniformly at the grain boundary. The results of the corrosion examination reveal that the Al₃Ti/ADC12 composite exhibited a minimum corrosion rate of 0.081 g·m–2·h–1 for an Sr content of 0.2wt%, which is two thirds of that of unmodified composite (0.134 g·m–2·h–1). This improved corrosion resistance was due to galvanic corrosion, which resulted from the low area ratio of the cathode to anode regions. This caused a low-density corrosion current in the composite, thereby yielding optimum corrosion resistance.     

非晶态Ni－P合金与TiC微粒复合镀的研究

利用复合电镀技术，制备了非晶态Ｎｉ－Ｐ合金基ＴｉＣ复合镀层．测定了非晶态Ｎｉ－Ｐ合金镀层和（Ｎｉ－Ｐ）－ＴｉＣ复合镀层的表面形貌、结构、硬度以及耐磨性．研究了ＴｉＣ微粒对镀层的弥散强化作用．结果表明，与非晶态Ｎｉ－Ｐ合金镀层相比，（Ｎｉ－Ｐ）－ＴｉＣ复合镀层的硬度和耐磨性均超过了非晶态Ｎｉ－Ｐ合金镀层．     

Effect of Al2O3 and Y2O3 on the corrosion behavior of ZrO2-benzotriazole nanostructured coatings applied on AA2024 via a sol-gel method

zirconia-based nanostructured coatings were deposited on AA2024 to improve the corrosion resistance properties. Three different nanostructured coatings, namely, zirconia-benzotriazole, zirconia-alumina-benzotriazole, and zirconia-yttria-benzotriazole, were applied on AA2024 via a sol-gel method using the dip-coating technique. Next, the coatings were annealed at 150℃ after each dipping period. The phases and morphologies of the coatings were investigated using grazing incidence X-ray diffraction (GIXRD), Fourier transform infrared spectroscopy (FT-IR), field emission scanning electron microscopy (FESEM), and atomic force microscopy (AFM). The corrosion properties were evaluated using electrochemical methods, including polarization and electrochemical impedance techniques in 3.5wt% NaCl solution. The obtained results confirm the formation of homogeneous and crack free zirconia-benzotriazole-based nanostructured coatings. The average roughness values for zirconia-benzotriazole, zirconia-alumina-benzotriazole, and zirconia-yttria-benzotriazole nanostructured coatings were 30, 8, and 6 nm, respectively. The presence of alumina as a stabilizer on zirconia coating was found to have a beneficial impact on the stability of the corrosion resistance for different immersion times. In fact, the addition of alumina resulted in the dominance of the healing behavior in competition with the corrosion process of zirconia-benzotriazole nanostructured coating.     

8-羟基喹啉插层双氢氧化膜与溶胶–凝胶涂层对镁合金的腐蚀防护性能研究

采用8-羟基喹啉（8-HQ）插层双氢氧化物（LDH）膜为底层和溶胶–凝胶层相结合的方法,对AM60B镁合金进行了腐蚀防护性能的研究。采用扫描电子显微镜（SEM）、场发射扫描电子显微镜（FESEM）、能量色散X射线能谱（EDS）、X射线衍射（XRD）、原子力显微镜（AFM）和电化学阻抗谱（EIS）等方法对LDH、LDH/溶胶–凝胶和LDH@HQ/溶胶–凝胶涂层进行分析。SEM图像显示,垂直生长的纳米片组成的LDH膜完全覆盖在表面。LDH/溶胶–凝胶和LDH@HQ/溶胶–凝胶涂层的形貌相同。此外,除了LDH@HQ/溶胶–凝胶涂层具有相对较高的表面粗糙度外,两种复合涂层的形貌几乎相同。虽然在3.5wt% NaCl溶液中,LDH膜具有与合金样品相同的阻抗行为,但其耐蚀性要高得多,这可能是由于其阻隔性以及对氯离子的捕获。与LDH薄膜相似,随着暴露时间的延长,LDH/溶胶–凝胶复合材料的耐蚀性降低。但其值远高于LDH膜,这主要与溶液路径的封闭有关。LDH@HQ/溶胶–凝胶复合材料的抗腐蚀性能优于LDH/溶胶–凝胶涂层,原因是8-HQ通过络合作用吸附在损伤部位。     

Improvement in the protective performance and adhesion of polypyrrole coating on AZ31 Mg alloys

The electrochemical synthesis of polypyrrole (Ppy) coating on AZ31 magnesium alloy was successfully achieved in a solution containing sodium salicylate and monomer of pyrrole through cyclic voltammetry technique. The effect of potential range, passivation pretreatment and number of cycles of polymerization on the quality and protective performance of the coatings was evaluated using surface analysis and electrochemical techniques. Through taking the advantage of charge transfer resistance, current density, corrosion potential, optical microscopy images and SEM micrographs, the optimum condition of synthesis of a Ppy coating with the best adhesion and corrosion protection was determined. The optimal PPy coating synthesized over AZ31 increases the polarization resistance and decreases the corrosion current more than one order of magnitude and shift the corrosion potential about 200 mV toward nobler potentials. The SEM studies showed that Ppy coating have cauliflower morphology of Ppy grains with a diameter ranging from 20 nm to 60 nm.     

热浸Zn-Ti合金镀层的显微组织与耐蚀性能

为了抑制热镀锌过程中因含硅活性钢引起的镀层超厚生长,本文采用在纯锌浴中加Ti的方法,研究了0.09%Si钢在含低于0.1%Ti的几种锌浴中热浸镀获得的组织,并采用盐雾腐蚀,电化学极化以及X射线光电子能谱等方法,研究了Zn和Zn-Ti镀层的耐蚀性能。结果表明,随着锌浴中Ti含量的增加,Ti对ζ相生长的抑制作用增强,合金层厚度逐渐减薄,Ti能有效地抑制含硅活性钢镀层的超厚生长。当Ti含量大于0.05%时,镀层中出现Γ2粒子。Zn-Ti合金镀层在5%NaCl溶液中发生自发腐蚀的倾向小于Zn镀层,其极化电阻增大,腐蚀电流密度减小,耐蚀性能提高。Zn-Ti镀层表面形成的氧化膜由ZnO 和TiO2组成。锌钛合金镀层的耐腐蚀性能优于纯锌镀层是由于在镀层表面形成了更加稳定的TiO2膜。     

In-situ reduced graphene oxide-polyvinyl alcohol composite coatings as protective layers on magnesium substrates

A simple and feasible method was developed to fabricate in-situ reduced graphene oxide-polyvinyl alcohol composite(GO-PVA) coatings as protective layers on magnesium substrates.Polyvinyl alcohol was used as an in-situ reductant to transform GO into reduced GO.Contiguous and uniform GO-PVA coatings were prepared on magnesium substrates by dip-coating method,and were further thermally treated at 120 ℃ under ambient condition to obtain in-situ reduced GO-PVA coatings.Owing to the reducing effect of PVA.thermal treatment at low temperature led to effective in-situ reduction of GO as confirmed by XRD,Raman,FTIR and XPS tests.The corrosion current density of magnesium substrates in 3.5 wt%NaCl solution could be lowered to its 1/25 when using in-situ reduced GO-PVA coatings as protective layers.     

含氯离子环境下锌铝伪合金涂层的耐蚀性及电化学特性

采用盐雾试验和电化学阻抗谱测试技术研究了纯锌和锌铝伪合金涂层在含氯离子环境中的腐蚀行为和电化学特性,通过扫描电镜、X射线物相分析等手段研究了原始涂层及腐蚀后的表面形貌和腐蚀产物的相结构,并对两种涂层的腐蚀机理进行了初步的探讨.随着盐雾时间的增加,纯锌涂层表面逐渐生成疏松多孔的胞状腐蚀产物层,主要腐蚀产物为Zn5(OH)8-Cl2H2O、ZnO和Zn5(CO3)2(OH)6,盐雾试验达到768 h后腐蚀产物层局部区域发生龟裂.锌铝伪合金涂层表面生成致密的腐蚀产物层,主要为Zn5(OH)8Cl2H2O、Zn0.71Al0.29(OH)2(CO3)0.145.xH2O及ZnAl2O4.电化学阻抗谱测试结果表明:随着盐雾时间的延长,两种涂层的电荷转移电阻均逐渐增大,但锌铝伪合金涂层的阻抗要明显大于纯锌涂层,表现出了更好的耐蚀性.     

Cu48Zr43Al9合金在0.05mol/L Na2SO4介质中腐蚀电化学行为研究

采用真空电弧熔炼法制备Cu48Zr43Al9晶态合金及铜模铸造法制备Cu48Zr43Al9非晶合金。通过极化曲线和交流阻抗谱技术研究了Cu48Zr43Al9晶态和非晶态合金在0.05 mol/LNa2SO4溶液中腐蚀电化学行为。结果表明,在0.05 mol/LNa2SO4溶液中,Cu48Zr43Al9晶态和非晶态合金的交流阻抗谱均呈单容抗弧,实验结果说明合金的腐蚀过程是由电化学控制。与非晶合金相比,腐蚀电位负移,晶态合金的电荷传递电阻减小,腐蚀电流密度变大,腐蚀速度加快。在0.05mol/LNa2SO4溶液中,Cu48Zr43Al9非晶态合金具有良好的耐腐蚀性能,这是因为非晶态合金不具有晶格缺陷,结构均一稳定。     

纳米SiO2粒子复合对聚脲涂层耐蚀性能的影响

采用紫外光暴露+冷凝的紫外加速老化试验,结合表面形貌观察测试了纳米SiO2粉体复合聚脲涂层的光老化性能,采用3·5%NaCl溶液浸泡试验测试了涂层的耐海水浸泡腐蚀性能,通过场发射扫描电子显微镜、自腐蚀电位和交流阻抗图谱等分析了不同涂层的耐蚀性能.结果表明:纳米SiO2粉体显著提高了芳香族聚脲涂层的耐蚀性能,自腐蚀电位由-40mV升高至60mV,电化学阻抗模值增加了约一个数量级,涂层进入迅速老化阶段的时间延长了约120h,在3·5%NaCl溶液中的浸泡寿命提高了约600h.