Preparation and characterization of compact TiO_2 film used in Gratzel solar cells

We report for the first time the preparation method of compact TiO2 film using titanium butox-ide-petroleum ether solution, by means of dipping and sintering. Our estimation of the component of this thin film was confirmed by XPS test. Studies of AFM showed the influence of preparation condition upon surface morphology. The transmitted spectrum of this compact TiO2 film was also investigated, which presented an excellent transmittance of this film in the visible light region. We arrive at a conclusion, according to the Ⅰ-Ⅴ characteristics of solid-state Gratzel solar cells utilizing this kind of compact film, that this compact TiO2 film functions well in secluding the conducting substrate from the hole-conducting material.     

Preparation of graphene and TiO2 layer by layer composite with highly photocatalytic efficiency

A process for fabricating graphene and TiO2 layer by layer composite was introduced to improve the photocatalytic activity by controlling the layers, thickness and the mass ratio between graphene and TiO2. The graphene oxide (GO) was synthesized from natural graphite pow der by the modified Hummers met hod. Large-area uniform GO and TiO2 thin films were made by a spin-coating process in turn. After exposure of the TiO2/GO multilayer film to UV light irradiation which allows the reduction of GO to graphene, a novel photocatalyt ic structure as graphene and TiO2 layer by layer composite was synthesized. The cross-sectional SEM image showed that a clear layer by layer microstructure with a single layer thickness of graphene or TiO2 was in the range of about 50 nm. The total thickness of the film was around 5 μm which was varied according to the layer number of spin coating process. Raman spectra revealed th at significant structural changes occurred through UV light irradiation. Photodegrada tion for methylene blue (MB) exhibited that the layer by layer com posite is of higher photocatalytic activity than the pure TiO2 layer.     

Optical parameters induced by phase transformation in RF magnetron sputtered TiO2nanostructured thin films

Pure TiO2 thin films were deposited onto quartz substrates using a ceramic TiO2 target at an elevated substrate temperature of 573 K by RF magnetron sputtering, and an analysis of structural, optical and photoluminescence characteristics of the films upon phase transformation is reported in this paper. Structural investigations using X-ray diffraction revealed that the as-deposited film was amorphous in nature. Thermal annealing for 2 h at 873 K in air resulted in the formation of anatase phase, and a phase transformation to rutile was observed at 1073 K.An increase in grain size and an improvement in crystallinity were also observed on annealing. Rod- like rutile crystallites were observed in the SEM images of the film annealed at 1273 K. As-deposited films and films annealed up to 1073 K were highly transparent in the visible region with a transparency 480%. Optical band gap of the films decreased upon thermal annealing which is attributed to phase transformation from amorphous to anatase and then to rutile. Optical parameters such as refractive index, optical conductivity and optical dielectric constant increased with increase in annealing temperature. Since rutile is the optically active phase, the superior refractive index of the film annealed at 1073 K along with its high transparency in visible region suggests the application of this film in antireflective coatings. Photoluminescence emission of maximum intensity was observed for the film annealed at 873 K, which exhibits anatase phase. Intense blue emission observed in this film makes it suitable for use in optoelectronic display devices.     

Atomic spin gyroscope based on 129Xe-Cs comagnetometer

Atomic spin gyroscope (ASG) based on comagnetometer is a high sensitive and compact gyroscope for future inertial navigation applications. The start-up time was several hours of the demonstrated ASGs based on 3He-K or21 Ne-Rb-K comagnetometer, and only a few inertial navigation applications allow such a long time for preparation. We report the demonstration of an ASG based on 129Xe-Cs comagnetometer, which decreases the start-up time to 10 minutes and decreases the operation temperature by 40% as well. By operating this ASG in spin exchange relaxation free regime, a sensitivity of 7×10 -5 °/(s Hz1/2) was achieved.     

Photo-induced degradation of Ru（Ⅱ） complex absorbed on anatase TiO2 thin film electrode

Photo-induced degradation of a monolayer of Ru（Ⅱ） complex absorbed on anatase TiO2 thin film was studied by using resonant micro-Raman spectroscopy. Under intense light radiation of a laser and in the absence of a reducing agent, the dye decomposed quickly. When the dye-sensitized TiO2 thin film electrode was covered by a reducing agent, namely the I^-/I3^- redox couple, the photo-induced decomposing rate was slowed by a factor of -10^6. In both cases, the dye decomposed with time under an exponential law.     

Synthesis of TiO2 nanotubes film and its light scattering property

TiO2 nanotubes with diameters of 10 nm and lengths up to 600 nm were fabricated by directly using commercial TiO2 powders P25 as the precursors via sonication-hydrothermal combination approach. TiO2 nanotubes were characterized by means of X-ray powder diffractometer （XRD）, scanning electron microscope （SEM）, selected area electron diffraction pattern （SAED） and transmission elec- tron microscope （TEM）. The light scattering property of film electrodes modified with TiO2 nanotubes was studied and revealed that TiO2 nanotubes can be used as the light scattering centers to increase the light absorption in dye-sensitized solar cells. The TiO2 nanotubes film electrodes mixed with 10% small nanoparticles TiO2 had both strong light scattering property and fine mechanical characteristics, and this kind of electrodes can be used as electrodes in improving the conversion efficiencies of dye-sensitized solar cells.     

Photoelectrochemical synergetic degradation of Acid Orange II with TiO2 modified β-PbO2 electrode

Electrochemically assisted photocatalysis is an effective approach to improve photocatalytic efficiency. In this paper, modified β-PbO2 electrode was prepared by TiO2 co-deposition and characterized by SEM and XRD. Then 2.0g TiO2 modified β-PbO2 electrode (2.0 g TiO2 involved in the 200 mL co-deposition solution) was used in electrochemically assisted photocatalytic degradation of Acid Orange II and the influence of initial pH values was investigated when the potential applied across the electrodes was 1.5 V. When the potential applied was 2.5 V, the difference of the degradation process and the final products were studied. The results indicated that 2.0 g TiO2 modified β-PbO2 electrode was different from the unmodified one in that the β-PbO2 crystals became finer and the electrode became more compact and more uniform. The synergetic effect in electrochemically assisted photocatalytic degradation of Acid Orange Ⅱ was observed and degradation efficiency and TOC removal were the highest at initial solution pH 2.0. By UV-visible spectral analysis, it was proved that photoelectrochemical synergetic degradation of Acid Orange Ⅱ went through the step of producing main product maleic acid for the solution at the initial pH 2.0 within 2 h, but the degradation was slow for the solution at the initial pH 12.0.     

Nanodiamond films deposited at moderate temperature on pure titanium substrate pretreated by ultrasonic scratching in diamond powder suspension

Nanocrystalline diamond (NCD) film deposition on pure titanium and Ti alloys is extraordinarily difficult because of the high diffusion coefficient of carbon in Ti, the large mismatch in their thermal expansion coefficients, the complex nature of the inter-layer formed during diamond deposition, and the difficulty to achieve very high nucleation density. In this investigation, NCD films were successfully deposited on pure Ti substrate by using a novel substrate pretreatment of ultrasonic scratching in a diamond powder-ethanol suspension and by a two-step process at moderate temperature. It was shown that by scratching with a 30-μm diamond suspension for 1 h, followed by a 10-h diamond deposition, a continuous NCD film was obtained with an average grain size of about 200 nm. Detailed experimental results on the preparation, characterization, and successful deposition of the NCD films on Ti were discussed.     

Photocatalytic oxidation of gaseous benzene over nanosized TiO2 prepared by solvothermal method

Nanosized TiO2 particles were prepared by solvothermal method using tetrabutyl titanate as precursor,ethanol and water as solvents,and a facile immobilization method of nanosized TiO2 particles on woven glass fabric was developed. The samples obtained under various preparation conditions were charac-terized by means of thermo gravimetric analysis(TG) and differential scanning calorimetry(DSC) ,X-ray diffraction(XRD) ,transmission electron microscopy(TEM) ,high resolution-transmission electron mi-croscopy(HR-TEM) ,and Brunauer-Emmett-Teller(BET) . The results show that the cube-shape of TiO2 prepared by solvothermal method has good crystallinity of(101) surface,higher thermal stability and large specific surface area. Scanning electron microscopy(SEM) images confirmed that the immobi-lized TiO2 film was uniformly distributed and clung to the substrate firmly. The photocatalytic activity of the catalysts was tested using photocatalytic oxidation of gaseous benzene. The results show that the TiO2 calcined after solvothermal treatment suffers from lower specific surface area,and hence de-creases its photocatalytic activity. The photocatalytic activities of the TiO2 by solvothermal treatment with or without calcination in degradation 400 mg/m3 benzene are 3.7 and 4.1 times as high as catalyst without solvothermal treatment,respectively.     

Study on anti-pollution nano-preparation or dimethomorph and its performance

The photocatalysis of nanometer TiO2/Ag was modified by sodium dodecyl sulfate, and its behavior of adsorption for pesticide was investigated on the surface of catalyst. Four kinds of water-solubility preparations were prepared by using TiO2/Ag, modified TiO2/Ag by 0.5% SDS, TiO2 and nothingness as photocatalyst with dimethomorph as effective component. They were besmeared on a piece of glass, and the photocatalytic experiment was done in sunlight. Degradation rates of 1.2 % dimethomorph are 71.5 %, 68.0 %, 45.5% and 28.3%, respectively, when it was degraded in five days. Degradation rate of 10% dimethomorph is 97.3% in eight days in sunlight and ti/2 is 2.8 d in nano-preparation, when it was sprayed on small cabbages after being diluted in rudimental experiments of toxicity for crop. The nano-preparation is of better biologic activity, the virulence of which is 1.235 times as great as original pesticide and 1.245 times as ordinary preparation under the same condition.     

Research on the technology of femtosecond laser micromachining based on image edge tracing

Aiming at fabrication of complex microstructures and micro-patterns, a kind of femtosecond laser micromachining technology based on the BMP image edge tracing was proposed. We introduced the general principle of this technology and discussed the implementation of the machining paths extraction, optimization, tracing and the feedback of the machining procession in detail. On the basis of this technology, control software for femtosecond laser micromachining was developed. Furthermore, we have accomplished the fabrication of complicated two-dimensional (2D) micro-patterns on a copper thin film. The results indicate that this technology can be used for digital control micromachining of complex patterns or microstructures at micron and submicron scales by femtosecond laser.     

The Effect of Chelating Copolymer Additive on the Yttrium Iron Garnet Nanoparticle Formation

1 Results Yttrium iron garnet (YIG) is a well-known ferromagnetic garnet material and has widely used in electronic devices[1].A new acrylic chelating polymer was developed to act as the additive of the preparation of YIG precursor in our previous study[2].The sintering temperature of YIG nanocrystal obtained by this YIG precursor (ACP) was magnificently descended from 1 000 to 600 ℃.In this study,we were further to study the effect of amount of chelating polymer and the compositions of chelating polymer on the YIG nanocrystal preparation and its magnetic properties.A series of the acrylic chelating polymer,poly(butyl acrylates-co-glycidyl methacrylate-co-2-methylacrylic acid 3-(bis-carboxymethylamino)-2-hydroxy-propyl ester) was prepared by using soap-free emulsion polymerization.     

Dissolution and diffusion of TiO2 in the CaO-Al2O3-SiO2 slag

The dissolution of TiO2 in the CaO-Al2O3-SiO2 slag under static conditions was studied in the temperature range from 1643 K to 1703 K. After TiO2 dissolved, the microstructure of the interface between TiO2 and the slag was observed by scanning electron microscopy, and the concentration profiles of Ti4＋and other ions across the TiO2/slag interfaces were analyzed by energy-dispersive X-ray spectroscopy. On the basis of these results, the dissolution behavior of TiO2 was evaluated, and the diffusivity of Ti4＋in the bulk slag was estimated. Ac-cording to the Stokes-Einstein relation, the viscosity calculated by a previously reported model gave a diffusivity of Ti4＋ions greater than that estimated by the concentration profiles of Ti4＋ions. The mechanism of TiO2 dissolution in the CaO-Al2O3-SiO2 slag is discussed in de-tail.     

Preparation of porous nanocrystalline TiO2 electrode by screen-printing technique

Different paste has been used for preparing porous TiO2 thin film by screen-printing technique, the main component of it comes from commercial TiO2 P25 power. The dye-sensitized solar cell based on this TiO2 thin film without further chemical treatments exhibits high overall conversion efficiency of 5.81%―6.70%, even with low TiO2 content and thin film thickness. The experimental repeatability is nice and the properties of the films are uniform.     

Critical relative indentation depth in carbon based thinfilms

The thin film hardness estimation by nanoindentation is influenced by substrate beyond a critical relative indentation depth(CRID). In this study we developed a methodology to identify the CRID in amorphous carbon film. Three types of amorphous carbon film deposited on silicon have been studied. The nanoindentation tests were carried out applying a 0.1–10 mN load range on a Berkovich diamond tip, leading to penetration depth-to-film thickness ratios of 8–100%. The work regained during unloading(We) and the work performed during loading(Wt) was estimated for each indentation. The trend of unload-to-load ratio(We/Wt) data as a function of depth has been studied. We/Wtdepth profiles showed a sigmoid trend and the data were fitted by means of a Hill sigmoid equation. Using Hill sigmoid fit and a simple analytical method it is possible to estimate CRID of carbon based films.     

Investigation of the deterioration of passive films in H_2S-containing solutions

The effect of H_2S on the corrosion behavior of 316 L stainless steel was investigated using electrochemical methods by changing the gas condition from CO_2 to H_2S and then back to CO_2. The presence of H_2S showed an acceleration effect on the corrosion of 316 L stainless steel in comparison with CO_2. The acceleration effect remained even after the complete removal of H_2S by CO_2, indicating that the passive film was irreversibly damaged. X-ray photoelectron spectroscopy(XPS) analysis indicated that the passive film was composed of Cr_2O_3, Fe_2O_3, and FeS_2 after being immersed in H_2S-containing solutions. The semiconducting property of the passive film was then investigated by using the Mott–Schottky approach. The presence of sulfides resulted in higher acceptor and donor densities and thus was responsible for the deterioration of passive films.     

Study on cellular internalization of poly（vinyldiaminotriazine）-based hydrogen bonding type non-viral transgene vector

Previously we successfully prepared poly（vinyldiaminotriazine）（PVDT）-based non-viral vectors which complexed piasmid DNA via hydrogen bonding with adenine-thymine base pairs, in this report, surface charges and complex sizes of this system were further examined. The results showed that PVDT-based polymer could cover surface charges of DNA resulting in slightly negative or neutral complexes. It was also found that the complex sizes were governed by two events： the aggregation induced by the instability of neutral particles, and more compact complexes produced by PVDT-based polymers. In the study of cellular uptake, chlorpromazine and filipin III were used to inhibit clathrin-and caveolae-mediated endocytosis, respectively. We found that PVDT-based systems were transported into cells via a non-clathrin, non-caveolae mediated endocytosis. This special process was studied by temperature inhibition and kinetics assays. It was revealed that such a pathway was characterized by （i） a more en- ergy dependent process and （ii） a much slow transfection-effective internalization.     

Induction of Apoptosis in Purified Nuclei from Tobacco-Suspension Cells by Cytochrome b6／f Complex

An apoptotic cell-free system containing cytosol and nuclei from normally cultured tobacco suspension cells was used to show that a spinach chloroplast preparation can induce apoptosis in nuclei, evidenced by DNA electrophoresis and fluorescence microscopy observations, Further study showed that the chloroplast preparation or its pellet (thylakoid membrane) after hypoosmotic or supersonic treatment still exhibited the apoptosis-inducing activity, but the supernatant had no effect, which indicates that the apoptosisinducing effector in the chloroplast preparation is water-insoluble. The induction of apoptosis by chloroplast preparation could be attenuated by Ac-DEVD-CHO, the specific inhibitor of Caspase-3, implying involvement of a Caspase-3-1ike protease during the process. Furthermore, extensive apoptosis in nuclei was induced by cytochrome b6/f on the thylakoid membrane, indicating that this important cytochrome complex may have an important role in the chloroplast-related apoptotic pathway.     

Preparation and magnetic properties of CoFe2O4/TiO2 composite films

Using （Ti（OC4H9）4） and metal chlorates as starting materials, CoFe2O4/TiO2 composite films were prepared by sol-gel method. The effects of heat treatment temperature and pH of the precursor on microstructure and magnetic properties were studied. The phase structure of the samples was examined by X-ray diffraction. The microstructure was examined by scanning electron microscope, atomic force microscope and polarized microscope. The magnetic property was measured by vibrating sample magnetometer. The results show that the crystals of different phases grow up independently. CoFe2O4 is uniformly embedded into the TiO2 matrix in the prepared composite films, and the growth of composite films is dependent on the heat treatment temperatures and PH of the precursor. The average size of CoFe2O4 crystal is 19 nm in Nanocomposite film prepared when the heat treatment temperature is 800℃ and the pH of the precursor is between 2 and 3. The magnetism of the composite films is enhanced as the heat treatment temperature increases.     

Influence of B source materials on the synthesis of TiB2-Al2O3 nanocomposite powders by mechanical alloying

An Al2O3-TiB2 nanocomposite was successfully synthesized by ball milling of Al, TiO2 and two B source materials of B2O3 （system （1）） and H3BO3 （system （2））. Phase identification of the milled samples was examined by Xray diffraction. The morphology and microstructure of the milled powders were monitored by scanning electron microscopy and transmission electron microscopy. It was found that the formation of this composite was completed after 15 and 30 h of milling time in systems （1） and （2）, respectively. More milling energy was required for the formation of this composite in system （2） due to the lubricant properties of HaBO3 and also its decomposition to HBO2 and B2O3 during milling. On the basis of X-ray diffraction patterns and thermodynamic calculations, this composite was formed by highly exothermic mechanically induced self-sustaining reactions （MSR） in both systems. The MSR mode took place around 9 h and 25 h of milling in systems （1） and （2）, respectively. At the end of milling （15 h for system （1） and 30 h for system （2）） the grain size of about 35-50 nm was obtained in both systems.