Crystallization dynamics of supersaturated NaClO4 aerosols studied by high-speed photography

Single supersaturated NaClO4 aerosol droplets on a quartz substrate were observed by a high-speed video camera for their morphologic changes with decreasing relative humidity （RH）. The supersaturated droplets were found to form anhydrous NaClO4 at -10% RH. Three stages were roughly observed in this process, i.e., the main stem appearance, primary and secondary branches growth, and the deep dehydration. The main stem grew steadily and finished in 120 ms. Affected by both crystal precipitation and water evaporation, primary branches grew for 1200 ms, accompanied by a slower growth of secondary branches. The deep dehydration was more complicated, and lasted for a longer time.     

Compression behavior and equation of state of Ni77P23 amorphous alloy

The compression behavior of Ni77P23 amorphous alloy is investigated at room temperature in a diamond-anvil cell instrument using insitu high pressure energy dispersive X-ray diffraction with a syn- chrotron radiation source. The equation of state is determined by fitting the experimental data accord- ing to Birch-Murnaghan equation: -ΔV/V0=0.08606P-3.2×10-4P2 5.7×10-6P3. It is found that the structure of Ni77P23 amorphous alloy is stable under pressures up to 30.5 GPa.     

<Emphasis Type="Italic">Ab initio</Emphasis> study of the effects of Ag/Mn doping on the electronic structure of LiFePO<Subscript>4</Subscript>

Based on density functional theory （DFT） of the first-principle for the cathode materials of lithium ion battery, the electronic structures of Li（Fe1-x）PO4 （Me = Ag/Mn, x = 0-0.40） are calculated by plane wave pseudo-potential method using Cambridge serial total energy package （CASTEP） program. The calculated results show that the Fermi level of mixed atoms Fe1-xAgx moves into its conduction bands （CBs） due to the Ag doping. The Li（Fe1-xAgx）PO4 system displays the periodic direct semiconductor characteristic with the increase of Ag-doped concentration. However, for Fe1-xMnx mixed atoms, the Fermi level is pined at the bottom of conduction bands （CBs）, which is ascribed to the interaction between Mn（3d） electrons and Fe（4s） electrons. The intensity of the partial density of states （PDOS） near the bottom of CBs becomes stronger with the increase of Mn-doped concentration. The Fermi energy of the Li（Fe1-xMnx）PO4 reaches maximum at x = 0.25, which is consistent with the experimental value of x = 0.20. The whole conduction property of Mn-doped LiFePO4 is superior to that of Ag-doped LiFePO4 cathode material, but the structural stability is reverse.     

Theoretical study on the lithium bond interaction of furan homologues C4H4Y （Y=O,S） with LiCH3 via DFT and MP2

The optimizations geometries and interaction energy corrected by BSSE of the complexes between C4H4Y （Y=O, S） and CHiLi have been calculated at the B3LYP/6-311＋＋G^＊＊ and MP2/6-311＋＋G^＊＊ levels. Three complexes were obtained. Abnormally, the calculations showed that all the C10--Li14 bond lengths increased obviously but the blue-shift of C10-Li14 stretching frequency occurred after formed complexes. The calculated binding energy with basis set super-position error （BSSE） and zero-point vibrational energy corrections of complexes I-III is -45.757, -35.700 and -39.107 kJ·mol^-1, respectively. The analyses on the combining interaction with the atom-in-molecules theory （AIM） also showed that a relatively strong lithium bond interaction presented in furan homologues C4H4Y-LiCH3 systems. Natural bond orbital theory （NBO） analysis has been performed, and the results revealed that the complex I is formed with n-σ type lithium bond interaction between C4H40 and LiCH3, complex II is formed with TT-s type lithium bond interaction between C4H4O and LiCH3, and complex III is formed with TT-s and n-s type lithium bond interactions between C4H4S and LiCH3, respectively.     

Investigation of the cross-reaction mechanism of C<Subscript>6</Subscript>H<Subscript>5</Subscript>F-HNO<Subscript>2</Subscript> aqueous solution irradiated at 355 nm by transient absorbance spectrum technique

The transient absorption spectrum technique was employed to investigate the cross-reaction mechanism of C6H5F-HNO2 aqueous solution irradiated at 355 nm. The characteristic and the kinetic parameters of transient species were also detected. Hydroxyl radical derived from the photolysis of HNO2 was added to monofluorobenzene with a second-order rate constant of （5.83±0.17）×10^9 L·mol^-1·s^-1 to form an adduct, C6H5F…OH, which was able to react with HNO2 as the main reaction pathway with a rate constant of （8.3±0.1）×10^7 L·mol^-1·s^-1. The C6F6…OH adduct can also be decayed by elimination of H2O to yield monofluorophenyl radical C6H4F-. By GC-MS technique, the final products were identified to be monofluorophenol, nitro-monofluorobenzene, nitro-monofluorophenol and para-fluorobiphenyl.     

Research on C<Subscript>3</Subscript>N<Subscript>4</Subscript> superhard compound thin film and its application

By combination of DC reactive magnetron sputtering with multiple arcplating, the alternating C₃N₄/TiN compound film is deposited onto HSS. The core level binding energy and the contents of carbon and nitrogen are characterized by X-ray photoelectron spectrum. X-ray diffraction (XRD) shows that compound thin film contains hard crystalline phases of α-C₃N₄ and β-C₃N₄. The Knoop microhardness in the load range of 50, 5–54, 1 GPa is measured. According to acoustic emission scratch test, the critical load values for the coatings on HSS substrates are in the range of 40–80 N. The metal coated with C₃N₄/TiN compound films has a great improvement in the resistance against corrosion. Many tests show that such a coating has a very high wearability. Compared with the uncoated and TiN coated tools, the C₃N₄/TiN coated tools have a much longer cutting life. Foundation item: Supported by the National Natural Science Foundation of China (19875037) Biography: Wu Da-we( (1941-), male, Professor, research direction; thin film and its application.     

Theoretic study of the reaction mechanism between （Me）3CO· radical and trans-3-hexene

The reaction mechanism between （Me）3CO· radical and trans-3-hexene in benzene was studied for the first time at the B3LYP/6-311＋＋G（d,p）//B3LYP/6-31G（d）＋ZPVE level. Two distinct elementary channels were identified as： （1） abstraction-addition; （2） addition-addition-elimination. Analysis of the potential energy surface demonstrates that for the title reaction, channels （1） and （2） have the major and minor contribution, respectively. Our calculated results can well explain the recently observed product distribution by Coseri et al. （J. Org. Chem. 2005, 70, 4629）. However, we found that the addition-abstraction channel proposed by Coseri et al. is kinetically infeasible.     

Comparison of the carbon isotope composition of total organic carbon and long-chain <Emphasis Type="Italic">n</Emphasis>-alkanes from surface soils in eastern China and their significance

Surface soil samples collected over a high spatial resolution in eastern China were analyzed for carbon isotope composition （δ^13C） of total organic carbon （TOC） and higher plant-derived long-chain n-alkanes, with the latter reported as weighted mean values. The two sets of δ^13C values are significantly correlated and show similar trends in spatial variation. The spatial distribution of δ^13C shows less negative values in the mid-latitudes between 31°N and 40°N and more negative ones at higher and lower latitudes. This is consistent with previously reported carbon isotope data from surface soil phytoliths in the same region and suggests that the mid-latitude area provides relatively favorable growing condi- tions for C4 plants. Furthermore, δ^13C values of both TOC and long-chain n-alkanes from 12 surface soil samples collected from a small grassland in north China displayed similar carbon isotope values and the difference between paired δ^13C of a soil samples remains relatively constant. Our data demonstrate that in eastern China, soil δ^13C composition of both TOC and long-chain n-alkanes is effective indicators of C3/C4 ratios of the prevailing vegetation. This work suggests that -22‰ and -32‰ are good es- timated end members for the weighted mean δ^13C values of long-chain n-alkanes （C27, C29 and C31 n-alkanes） from soils under dominant C4 or C3 vegetation, allowing us to reconstruct paleovegetation trends.     

Synthesis and characterization of wormhole-like mesoporous Ce0.6Zr0.35Y0.05O2 solid solutions

Nanoparticles of Ce0.6Zr0.35Y0.05O2 (CZY) solid solution have been prepared by the CTAB (hexadecyl-trimethyl ammonium bromide), CTAB-EG (ethylene glycol) templating, and CTAB-EG-NaCl (in which the pores of the precursor synthesized by the CTAB-EG method is filled by a certain amount of NaCl) method, respectively. The physical properties of these materials were characterized by means of tech-niques such as X-ray diffraction (XRD), high resolution scanning electron microscopy (HRSEM), transmission electron microscopy (TEM), selected area electron diffraction (SAED), and N2 adsorp-tion-desorption measurements. The CZY samples synthesized by the above three methods display wormhole-like mesoporous morphology and cubic crystal structures. The materials are narrow in pore size distribution (averaged pore diameter = 5.3―7.1 nm), high in surface areas (95―119 m2/g), and large in pore volumes (0.16―0.18 cm3/g). It has been demonstrated that the introduction of NaCl is capable of retaining the pore structures of solid nanomaterials at high-temperature calcination.     

Fabrication of visible-light responsive S-F-codoped TiO<Subscript>2</Subscript> nanotubes

Fabrication and S-F-codoping of TiO2 nanotubes were carried out by a one-step electrochemical anodization process to extend the photoresponse of TiO2 to the visible-light region. The prepared samples were annealed in air and detected by SEM, XRD, XPS and UV-vis DRS spectrophotometer. The results showed that the average tube diameter of the nanotubes was 150 nm and the average tube length was 400 nm. The doped TiO2 nanotubes exhibited strong absorption in visible-light region. Photoelectrocatalytic degradation efficiency of 4-CP over S-F-codoped TiO2 nanotubes was 39.7% higher than that of only-F-doped sample. Moreover, sulfur and fluorine codoped into substitutional sites of TiO2 had been proven to be indispensable for strong response and high photocatalytic activity under visible light, as assessed by XPS.     

State of water and its implications for supersaturated structures in Mg(NO3)2 aerosols

One technique based on the difference spectra was developed to study the state of water in supersaturated Mg(NO₃)₂ aerosols. The technique could be derived from the observation that the Raman scattering and infrared absorbance cross sections of molecular vibrations of interest remain practically constant from diluted solutions to supersaturated aerosols. The spectra of solvated water were obtained and primarily related to the first hydration layers of solute molecules in supersaturated Mg(NO₃)₂ aerosols. Based on this investigation, a chain structure was proposed to occur in the supersaturated Mg(NO₃)₂ aerosols at low relative humidities (RHs). Supported by National Natural Science Foundation of China (Grant Nos. 20673010 and 20640420450), “111” Project (Grant No. B07012), and China Postdoctoral Science Foundation (Grant No. 20070410466)     

Different climatic controls of soil δ 13Corg in three mid-latitude regions of the Northern Hemisphere since the Last Glacial period

Paleoecological records of soil δ^13Corg from three regions in the middle latitudes of the Northern Hemisphere, including the Chinese Loess Plateau （CLP）, the Great Plains and adjacent areas of North America and northwestern Europe, showed different variations since the Last Glacial period. An attempt was made to evaluate the causes for the difference in δ^13Corg on the basis of the modern climatic data collected in these regions and of the modern C3 and C4 plant distributions. The analysis indicates that temperature, especially the growing season temperature, has a dominant control on the growth of C4 plants. When the mean annual or growing season temperatures are below the ＂threshold value＂, the growth of C4 plants is limited. When the temperature is above the ＂threshold value＂, C4 plants can grow under a wide range of precipitation. However, when the precipitation is high enough to favor the growth of trees, the proportions of C4 plants in local biomass will decline. The implicit control factor recovered by sedimentary records is consistent with the control factor on modern C3/C4 distribution. Pure C3 plants have been dominating the local biomass since the Last Glacial period in European loess region, mainly owing to the low local temperature. The increases in C4 plants from the late Pleistocene to the Holocene in the Chinese Loess Plateau, the Great Plains and adjacent areas, mainly reflect the influence of increasing temperature.     

Micro-Raman investigations on the structures of the surface and the inner of MgSO_4 droplets

Spherical MgSO4 droplets were deposited by a syringe on the hydrophobic Teflon substrate. Using micro-Raman technique, the laser beam was highly focused twice on the surface and in the center of spherical droplets. The Raman spectra for the surface and the inner of MgSO4 droplets were accord-ingly obtained, suggesting formation of a thin layer of gels on MgSO4 droplets at low relative humidity. The gel layer covered the surface and exhibited a significant delay in response to the change of ambi-ent relative humidity, resulting in the structural difference between the surface and the inner of MgSO4 droplets.     

Magnetoelectric and converse magnetoelectric res ponses in TbxDy1-xFe2-y alloy ＆ Pb（Mg1/3Nb2/3）（1-x）TixO3 crystal laminated composites

Measured results of magnetoelectric （ME） and converse magnetoelectric （CME） effects of TbxDy1-xFe2-y/ Pb（Mg1/3Nb2/3）（1-x）TixO3/TbxDy1-xFe2-y （TD/PMNT/TD） and PMNT/TD/PMNT laminated composites are presented. ME effect was determined by measuring laminate voltage output under a Helmholtz-generated AC field biased by a DC field （0-1 kOe） （1Oe = 79.58 A/m）. The CME effect was measured by recording the voltage induced in a solenoid encompassing the ME sample while exposed to a DC bias field and PMNT layer driven by a 10 V AC source. The ME and CME responses in the two laminated structure are linear. The highest values of ME coefficients in TD/PMNT/TD and PMNT/TD/PMNT composites are 384 mV/Oe and 158 mV/Oe, respectively, while the highest values of CME coefficients in the two composites are 118 mG/V and 162 mG/V （1 G=10^-4 T）, respectively.     

Composition dependence of viscosity for Al（1-x）Mgx（0≤x≤0. 10） alloys

Viscosities of molten Al（1-x）Mgx（0≤x≤0. 10 alloys have been measured in the temperature range of 973 K--1173 K by a torsional oscillation cup method. The viscosity dependence on temperature for Al（1-x）Mgx（0≤x≤0. 10 melts obeys Arrhenius equation. The viscosity increases with increasing magnesium concentration in the investigated system. There is an important relationship between viscosity and its glass-forming ability for metallic melt.     

Silicon field emission arrays coated with CN<Subscript>x</Subscript> thin films

Arrays of silicon micro-tips were made by etching the p-type (1 0 0) silicon wafers which had SiO₂ masks with alkaline solution. The density of the micro-tips is 2×10⁴ cm⁻². The Scanning Electron Microscope (SEM) photos showed that the tips in these arrays are uniform and orderly. The CN_x thin film, with the thickness of 1.27 μm was deposited on the silicon micro-tip arrays by using the middle frequency magnetron sputtering technology. The SEM photos showed that the films on the tips are smoothly without particles. Keeping the sharpness of the tips will benefit the properties of field emission. The X-ray photoelectron spectrum (XPS) showed that carbon, nitrogen and oxygen are the three major elements in the surfaces of the films. The percents of them are C: 69.5%, N: 12.6% and O: 17.9%. The silicon arrays coated with CN_x thin films had shown a good field emission characterization. The emission current intensity reached 3.2 mA/cm² at 32.8 V/μm, so it can be put into use. The result showed that the silicon arrays coated with CN_x thin films are likely to be good field emission cathode. The preparation and the characterization of the samples were discussed in detail. Foundation item: Supported by the National Natural Science Foundation of China (19975035) Biography: Chen Ming an (1978-), male, Ph. D candidate, research direction: novel functional materials film and ion beam modification of materials.     

High pressure effects on the crystal structure and electric conductivity of perovskite like（Ca/Sr）2CuO2Cl2 compounds

The crystal structure stability as well as electric conductance of （Sr/Ca）2CuO2Cl2 compound with K2NiF4 structure was investigated up to 31 GPa using diamond anvil technique. It seems that （Sr/Ca）2CuO2Cl2 is quite stable under pressure but with obvious anisotropic compressibility. The equation of state （EOS） obtained shows relative large bulk modulus.     

Thermoluminescence characteristics of Li2B4O7：Cu,As,P

This paper reports the thermoluminescence （TL） characteristics of lithium borate activated by Cu, Ag and P. The glow curves and spectra of thermoluminescence were measured, and the thermoluminescence response as a function of the absorbed dose and the fading behavior were studied. The results indicate that TL of this material has a low fading and wide linear dose response （10^-4-10^3 Gy）.     

Development and characterization of interspecific hybrids between <Emphasis Type="Italic">Oryza sativa</Emphasis> and <Subscript>O. latifolia</Subscript> by <Subscript>in situ</Subscript> hybridization

Oryza sativa and O. latifolia belong to the AA and CCDD genomes of Oryza, respectively. In this study, interspecific hybrids of these species were obtained using the embryo rescue technique. Hybrid panicle traits, such as long awns, small grain, exoteric large purple stigma, grain shattering and dispersed panicles, resemble that of the paternal parent, O. latifolia, whereas there is obvious heterosis in such respects as plant height, tillering ability and vegetative vigor. Chromosome pairing and the genomic components of the hybrid were subsequently investigated using genomic in situ hybridization （GISH） and fluorescent in situ hybridization （FISH） analysis. Based on the mitotic metaphase chromosome numbers of the root tips investigated, the hybrid is a triploid with 36 chromosomes. The genomic constitution of the hybrid is ACD. In the meiotic metaphase Ⅰ of the hybrid pollen mother cell, poor chromosome pairing was identified and most of the chromosomes were univalent, which resulted in complete male sterility in the hybrid.     

Novel trichromatic phosphor Co-doped with Eu, Tb in SiO2 gel matrix

The Eu, Tb co-doped SiO2 matrix tricolor fluorescence system was prepared by sol-gel technique. Red emission at 618 nm, green emission at 543 nm and blue emission at 350-500 nm were observed in the PL spectra of the sample, indicating that Eu^3＋, Eu^2＋ and Tb^3＋ ions coexisted in the matrix. In the co-doped sample, the blue emission of Eu^2＋ was much stronger than that of the sample single doped with Eu, which implied that the electron transfer between Eu^3＋ and Tb^3＋ maybe happened in the SiO2 matrix. The influences of the annealing temperature and Tb concentration on the PL spectra of the samples were investigated. The optimal doped concentration of Tb was determined to be 0.2% and the optimal annealing temperature 850℃. Annealed at 600℃, Tb^3＋ had a sensitizing effect on Eu^3＋ in the SiO2 matrix, and the emission intensity of Eu^3＋ in the Eu, Tb co-doped sample was more than four times that of the single doped sample, which could be attributed to the energy transfer from Tb^3＋ to Eu^3＋.