Mechanical and thermal properties of AA7075/TiO2/Fly ash hybrid composites obtained by hot forging

In the present paper, multiple reinforcements TiO2 and fly ash were utilized for the fabrication of AA7075 matrix based hybrid composites using stir casting technique followed by hot forging. In hybrid composites, the fly ash content was fixed to 3 wt% while that of TiO2 was varied from 2.5 to 10 wt%. Scanning electron microscopy images revealed homogenous dispersion of both the reinforcements in AA7075 matrix.Compression test was conducted to study the mechanical behaviour of hybrid composites. The hybrid composites showed increase in compressive strength with the incorporation of multiple reinforcements and further increased with the increase in the weight fractions of TiO2 particles. The coefficient of thermal expansion was measured between 50 and 250 ℃ with a high precision thermal mechanical analyser. The thermal coefficient of hybrid composites decreased with the addition of TiO2 and fly ash. However a slight decrease in thermal conductivity of hybrid composites was observed when compared to that of AA7075 alloy.     

Influence of rolling temperature on the interfaces and mechanical performance of graphene-reinforced aluminum-matrix composites

To study the influence of rolling on the interfaces and mechanical performance of graphene-reinforced Al-matrix composites,a rolling method was used to process them.Using scanning electron microscopy(SEM),transmission electron microscopy(TEM),X-ray diffraction(XRD),Raman spectroscopy,and tensile testing,this study analyzed the micromorphology,interfaces,and mechanical performance of the composites before and after rolling.The experimental results demonstrates that the composites after hot rolling has uniform structures with strong interfacial bonding.With an increase in rolling temperature,the tensile strength and elastic modulus of the composites gradually increase.However,when the rolling temperature is higher than 500°C,granular and rod-like Al4C3 phases are observed at the interfaces and the mechanical performance of the composites is degraded.When the rolling temperature is 480°C,the composites show the optimal comprehensive mechanical performance,with a tensile strength and elastic modulus of 403.3 MPa and 77.6 GPa,respectively,which represent increases of 31.6%and 36.9%,respectively,compared with the corresponding values prior to rolling.     

Microstructure and mechanical properties of SiC-particle-strengthening tri-metal Al/Cu/Ni composite produced by accumulative roll bonding process

In this study, a multilayer Al/Ni/Cu composite reinforced with SiC particles was produced using an accumulative roll bonding (ARB) process with different cycles. The microstructure and mechanical properties of this composite were investigated using optical and scanning microscopy and hardness and tensile testing. The results show that by increasing the applied strain, the Al/Ni/Cu multilayer composite converted from layer features to near a particle-strengthening characteristic. After the fifth ARB cycle, a composite with a uniform distribution of reinforcements (Cu, Ni, and SiC) was fabricated. The tensile strength of the composite increased from the initial sandwich structure to the first ARB cycle and then decreased from the first to the third ARB cycle. Upon reaching five ARB cycles, the tensile strength of the composite increased again. The variation in the elongation of the composite exhibited a tendency similar to that of its tensile strength. It is observed that with increasing strain, the microhardness values of the Al, Cu, and Ni layers increased, and that the dominant fracture mechanisms of Al and Cu were dimple formation and ductile fracture. In contrast, brittle fracture in specific plains was the main characteristic of Ni fractures.     

Effect of graphite powder as a forming filler on the mechanical properties of SiCp/Al composites by pressure infiltration

(38vol% SiCp + 2vol% Al₂O_3f)/2024 Al composites were fabricated by pressure infiltration. Graphite powder was introduced as a forming filler in preform preparation, and the effects of the powder size on the microstructures and mechanical properties of the final composites were investigated. The results showed that the composite with 15 μm graphite powder as a forming filler had the maximum tensile strength of 506 MPa, maximum yield strength of 489 MPa, and maximum elongation of 1.2%, which decreased to 490 MPa, 430 MPa, and 0.4%, respectively, on increasing the graphite powder size from 15 to 60 μm. The composite with 60 μm graphite powder showed the highest elastic modulus, and the value decreased from 129 to 113 GPa on decreasing the graphite powder size from 60 to 15 μm. The differences between these properties are related to the different microstructures of the corresponding composites, which determine their failure modes.     

In situ(α-Al_2O_3+ZrB_2)/Al composites with network distribution fabricated by reaction hot pressing

In situ(α-Al_2O_3+ZrB_2)/Al composites with network distribution were fabricated using low-energy ball milling and reaction hot pressing. Differential thermal analysis(DTA) was used to study the reaction mechanisms in the Al–Zr O2–B system. X-ray diffraction(XRD) and scanning electron microscopy(SEM) in conjunction with energy-dispersive X-ray spectroscopy(EDX) were used to investigate the composite phases, morphology, and microstructure of the composites. The effect of matrix network size on the microstructure and mechanical properties was investigated. The results show that the optimum sintering parameters to complete reactions in the Al–Zr O2–B system are 850°C and 60 min. In situ-synthesized α-Al2O3 and Zr B2 particles are dispersed uniformly around Al particles, forming a network microstructure; the diameters of the α-Al2O3 and Zr B2 particles are approximately 1–3 μm. When the size of Al powder increases from 60–110 μm to 150–300 μm, the overall surface contact between Al powders and reactants decreases, thereby increasing the local volume fraction of reinforcements from 12% to 21%. This increase of the local volume leads to a significant increase in microhardness of the in situ(α-Al2O3–Zr B2)/Al composites from Hv 163 to Hv 251.     

Hot deformation behavior of a Cr-containing low carbon steel in the ferrite range

A low carbon steel with Cr addition of 0.46wt% combined with trace elements of Mn and Ti was studied. The apparent activation energy of deformation and the hot deformation equation of the steel in the ferritic range were determined by means of single hot compression tests. The hot-rolled strip of 3 mm in thickness rolled in the ferritic range was obtained using a laboratory hot rolling mill. The mechanical properties show that the values of yield strength and ultimate tensile strength are 230 and 330 MPa, respectively, and the elongation is 33%. The average r-value is 1.1. Large polygonal ferrite recrystallization grains with about 40 grn in size and the strong { 111 } recrystallization texture can be obtained in the hot-rolled strip.     

Microstructure and mechanical properties of a hot-extruded Al-based composite reinforced with core–shell-structured Ti/Al_3Ti

An Al-based composite reinforced with core–shell-structured Ti/Al_3Ti was fabricated through a powder metallurgy route followed by hot extrusion and was found to exhibit promising mechanical properties. The ultimate tensile strength and elongation of the composite sintered at 620°C for 5 h and extruded at a mass ratio of 12.75:1 reached 304 MPa and 14%, respectively, and its compressive deformation reached 60%. The promising mechanical properties are due to the core–shell-structured reinforcement, which is mainly composed of Al_3Ti and Ti and is bonded strongly with the Al matrix, and to the reduced crack sensitivity of Al_3Ti. The refined grains after hot extrusion also contribute to the mechanical properties of this composite. The mechanical properties might be further improved through regulating the relative thickness of Al–Ti intermetallics and Ti metal layers by adjusting the sintering time and the subsequent extrusion process.     

Effect of Ti/B Additions on the Formation of Al3 Ti of in situ TiB2/Al Composites

A novel technique for fabricating TiB₂/Al composites in molten aluminum was introduced. The formation mechanism of brittle Al₃Ti particulates up to 30 m in size produced in the composites was studied and a method of eliminating them was proposed. The results show that (1) the brittle Al₃Ti particulates are always present in the composites when the molar ratio of Ti to B n_Ti:n_B is 1:2; and (2) the formation of the brittle Al₃Ti phase can be avoided entirely from the final product by using a proper n_Ti:n_B of l:4 in the Ti-B-Al preforms.In the former case, the tensile elongation of the composite is only 4%, much lower than the value of pure aluminum (20%). In the later case, the tensile elongation of this composite is 10%, higher than the value of the composite with a lot of Al₃Ti (4%), whereas the ultimate tensile strength of the former is nearly that of the later.     

Investigation on microstructural, mechanical and electrochemical properties of aluminum composites reinforced with graphene nanoplatelets

In present study, the microstructure, mechanical and electrochemical properties of aluminum–graphene nanoplatelets (GNPs) composites were investigated before and after extrusion. The contents of graphene nanoplatelets (GNPs) were varied from 0.25 to 1.0 wt.% in aluminum matrix. The composites were fabricated thorough powder metallurgy method, and the experimental results revealed that Al-0.25%GNPs composite showed better mechanical properties compared with pure Al, Al-0.50%GNPs and Al-0.1.0%GNPs composites. Before extrusion, the Al-0.25%GNPs composite showed ~13.5% improvement in ultimate tensile strength (UTS) and ~50% enhancement in failure strain over monolithic matrix. On the other hand, Al-0.50%GNPs and Al-0.1.0%GNPs composites showed the tensile strength lower than monolithic matrix. No significant change was observed in 0.2% yield strength (YS) of the composites. However, the extruded materials showed different trends. The 0.2%YS of composites increased with increase in GNPs filler weight fractions. Surprisingly, UTS of composites with 0.25 and 0.50% GNPs was lower than monolithic matrix. The failure strain of the baseline matrix was enhanced by ~46% with 0.25% graphene nanoplatelets. The superior mechanical properties (in terms of failure strain) of the Al-0.25%GNPs composite maybe attributed to 2-D structure, high surface area and curled nature of graphene. In addition, the corrosion resistance of pure Al and its composites reinforced with 0.5 and 1.0 wt% GNPs was also investigated. It was found that the corrosion rate increased considerably by the presence of GNPs.     

Microstructure and mechanical properties of a hot-extruded Al-based composite reinforced with core-shell-structured Ti/Al3Ti

An Al-based composite reinforced with core-shell-structured Ti/Al₃Ti was fabricated through a powder metallurgy route followed by hot extrusion and was found to exhibit promising mechanical properties. The ultimate tensile strength and elongation of the composite sintered at 620℃ for 5h and extruded at a mass ratio of 12.75:1 reached 304 MPa and 14%, respectively, and its compressive deformation reached 60%. The promising mechanical properties are due to the core-shell-structured reinforcement, which is mainly composed of Al₃Ti and Ti and is bonded strongly with the Al matrix, and to the reduced crack sensitivity of Al₃Ti. The refined grains after hot extrusion also contribute to the mechanical properties of this composite. The mechanical properties might be further improved through regulating the relative thickness of Al-Ti intermetallics and Ti metal layers by adjusting the sintering time and the subsequent extrusion process.     

Markedness and its Interpretation in Language Use

Language markedness is a common phenomenon in languages, and is reflected from hearing, vision and sense, i.e. the variation in the three aspects such as phonology, morphology and semantics. This paper focuses on the interpretation of markedness in language use following the three perspectives, i.e. pragmatic interpretation, psychological interpretation and cognitive interpretation, with an aim to define the function of markedness.     

Features of Women's language

Language is a means of verbal communication. People use language to communicate with each other. In the society, no two speakers are exactly alike in the way of speaking. Some differences are due to age, gender, statue and personality. Above all, gender is one of the obvious reasons. The writer of this paper tries to describe the features of women＇s language from these perspectives： pronunciation, intonation, diction, subjects, grammar and discourse. From the discussion of the features of women＇s language, more attention should be paid to language use in social context. What＇s more, the linguistic phenomena in a speaking community can be understood more thoroughly.     

An Analysis of Catherine＇s Character——Wuthering Heights

Wuthering Heights, Emily Bronte＇s only novel, was published in December of 1847 under the pseudonym Ellis Bell. The book did not gain immediate success, but it is now thought one of the finest novels in the English language. Catherine is the key character of this masterpiece, because everybody and everything center on her though she had a short life. We can understand this masterpiece better if we know Catherine well.     

Lower Paleozoic oil relationships within Williston Basin, Canada

The Williston Basin is a significant petroleum province, containing oil production zones that include the Middle Cambrian to Lower Ordovician, Upper Ordovician, Middle Devonian, Upper Devonian and Mississippian and within the Jurassic and Cretaceous. The oils of the Williston Basin exhibit a wide range of geochemical characteristics defined as "oil families", although the geochemical signature of the Cambrian Deadwood Formation and Lower Ordovician Winnipeg reservoired oils does not match any "oil family". Despite their close stratigraphic proximity, it is evident that the oils of the Lower Palaeozoic within the Williston Basin are distinct. This suggests the presence of a new "oil family" within the Williston Basin. Diagnostic geochemical signatures occur in the gasoline range chromatograms, within saturate fraction gas chromatograms and biomarker fingerprints. However, some of the established criteria and cross-plots that are currently used to segregate oils into distinct genetic families within the basin do not always meet with success, particularly when applied to the Lower Palaeozoic oils of the Deadwood and Winnipeg Formation.     

低渗透非均质砂岩油藏启动压力梯度研究

理论推导与室内实验相结合,建立了低渗透非均质砂岩油藏启动压力梯度确定方法。首先借助油藏流场与电场相似的原理,推导了非均质砂岩油藏启动压力梯度计算公式。其次基于稳定流实验方法,建立了非均质砂岩油藏启动压力梯度测试方法。结果表明:低渗透非均质砂岩油藏的启动压力梯度确定遵循两个等效原则。平面非均质油藏的启动压力梯度等于各级渗透率段的启动压力梯度关于长度的加权平均;纵向非均质油藏的启动压力梯度等于各渗透率层的启动压力梯度关于渗透率与渗流面积乘积的加权平均。研究成果可用于有效指导低渗透非均质砂岩油藏的合理井距确定,促进该类油藏的高效开发。     

On Tragic Consciousness In The Works By Ernest Hemingway

As an American modern novelist who were famous in the literary world, Hemingway was not a person who always followed the trend but a sharp observer. At the same time, he was a tragedy maestro, he paid great attention on existence, fate and end-result. The dramatis personae's tragedy of his works was an extreme limit by all means tragedy on the meaning of fearless challenge that failed. The beauty of tragedy was not produced on the destruction of life, but now this kind of value was in the impact activity. They performed for the reader about the tragedy on challenging for the limit and the death.     

Achieving Unusual States of Matter Under High Pressure

正The periodicity of the elements and the non-reactivity of the inner-shell electrons are two related principles of chemistry,rooted in the atomic shell structure.Within compounds,Group I elements,for example,invariably assume the+1 oxidation state,and their chemical properties differ completely from those of the p-block elements.These general rules govern our understanding of chemical structures and reactions.Using first principles calcula-     

Exchange-Correlation and Electronic Excitation Energies from Pairing Matrix Fluctuations

We have developed an adiabatic connection to formulate the ground-state exchange-correlation energy in terms of pairing matrix linear fluctuations.This formulation of the exchange-correlation energy opens a new channel for density functional approximations based on the many-body perturbation theory.We illustrate the potential of such approaches with an approximation based on the particle-particle Random Phase Approximation(pp-RPA).This re-     

Density Functional Theory for the Response of Periodic Systems to Electric Fields Based on the Vector Potential Approach

正The electronic and nuclear(structural/vibrational)response of 1D-3D nanoscale systems to electric fields gives rise to a host of optical,mechanical,spectral,etc.properties that are of high theoretical and applied interest.Due to the computational difficulty of treating such large systems it is convenient to model them as infinite and periodic(at least,in first approximation).The fundamental theoretical/computational problem in doing so is that     

On the Thermodynamic Limit for Responses to Static Electromagnetic Fields

For molecular systems,the quantum-mechanical treatment of their responses to static electromagnetic fields usually employs a scalar-potential treatment of the electric field and a vector-potential treatment of the magnetic field.Although the potential for each field separately is associated with the choice of an(unphysical)origin,the precise choice of the origin for the electrostatic field has little consequences for the results.This is different for the