具有良好可再生性的新型二氧化硅磁性氧化石墨烯纳米复合材料

Graphene oxide (GO) wrapped Fe₃O₄ nanoparticles (NPs) were prepared by coating the Fe₃O₄ NPs with a SiO₂ layer, and then modifying by amino groups, which interact with the GO nanosheets to form covalent bonding. The SiO₂ coating layer plays a key role in integrating the magnetic nanoparticles with the GO nanosheets. The effect of the amount of SiO₂ on the morphology, structure, adsorption, and regenerability of the composites was studied in detail. An appropriate SiO₂ layer can effectively induce the GO nanosheets to completely wrap the Fe₃O₄ NPs, forming a core-shell Fe₃O₄@SiO₂@GO composite where Fe₃O₄@SiO₂ NPs are firmly encapsulated by GO nanosheets. The optimized Fe₃O₄@SiO₂@GO sample exhibits a high saturated adsorption capacity of 253 mg·g?1 Pb(II) cations from wastewater, and the adsorption process is well fitted by Langmuir adsorption model. Notably, the composite displays excellent regeneration, maintaining a ~90% adsorption capacity for five cycles, while other samples decrease their adsorption capacity rapidly. This work provides a theoretical guidance to improve the regeneration of the GO-based adsorbents.     

微波预处理对复杂铜矿磨矿及浮选动力学的影响

The effect of CaCO₃, Na₂CO₃, and CaF₂ on the reduction roasting and magnetic separation of high-phosphorus iron ore containing phosphorus in the form of Fe₃PO₇ and apatite was investigated. The results revealed that Na₂CO₃ had the most significant effect on iron recovery and dephosphorization, followed by CaCO₃, the effect of CaF₂ was negligible. The mechanisms of CaCO₃, Na₂CO₃, and CaF₂ were investigated using X-ray diffraction (XRD), scanning electron microscopy and energy dispersive spectrometry (SEM–EDS). Without additives, Fe₃PO₇ was reduced to elemental phosphorus and formed an iron–phosphorus alloy with metallic iron. The addition of CaCO₃ reacted with Fe₃PO₇ to generate an enormous amount of Ca₃(PO₄)₂ and promoted the reduction of iron oxides. However, the growth of iron particles was inhibited. With the addition of Na₂CO₃, the phosphorus in Fe₃PO₇ migrated to nepheline and Na₂CO₃ improved the reduction of iron oxides and growth of iron particles. Therefore, the recovery of iron and the separation of iron and phosphorus were the best. In contrast, CaF₂ reacted with Fe₃PO₇ to form fine Ca₃(PO₄)₂ particles scattered around the iron particles, making the separation of iron and phosphorus difficult.     

不同硅饱和系数水榴石的碳酸化分解动力学

Carbonated decomposition of hydrogarnet is one of the vital reactions of the calcification–carbonation method, which is designed to dispose of low-grade bauxite and Bayer red mud and is a novel eco-friendly method. In this study, the effect of the silica saturation coefficient (x) on the carbonation of hydrogarnet was investigated from the kinetic perspective. The results indicated that the carbonation of hydrogarnets with different x values (x = 0.27, 0.36, 0.70, and 0.73) underwent two stages with significantly different rates, and the kinetic mechanisms of the two stages can be described by the kinetic functions R3 and D3. The apparent activation energies at Stages 1 and 2 were 41.96–81.64 and 14.80–34.84 kJ/mol, respectively. Moreover, the corresponding limiting steps of the two stages were interfacial chemical reaction and diffusion.     

一种超重力燃烧合成制备高性能高熵合金的新方法

A new method of high-gravity combustion synthesis (HGCS) followed by post-treatment (PT) is reported for preparing high-performance high-entropy alloys (HEAs), Cr_0.9FeNi_2.5V_0.2Al_0.5 alloy, whereby cheap thermite powder is used as the raw material. In this process, the HEA melt and the ceramic melt are rapidly formed by a strong exothermic combustion synthesis reaction and completely separated under a high-gravity field. Then, the master alloy is obtained after cooling. Subsequently, the master alloy is sequentially subjected to conventional vacuum arc melting (VAM), homogenization treatment, cold rolling, and annealing treatment to realize a tensile strength, yield strength, and elongation of 1250 MPa, 1075 MPa, and 2.9%, respectively. The present method is increasingly attractive due to its low cost of raw materials and the intermediate product obtained without high-temperature heating. Based on the calculation of phase separation kinetics in the high-temperature melt, it is expected that the final alloys with high performance can be prepared directly across master alloys with higher high-gravity coefficients.     

利用皮秒激光烧蚀制备非球形铝纳米颗粒

We report the picosecond laser ablation of aluminum targets immersed in a polar organic liquid (chloroform, CHCl₃) with ~2 ps laser pulses at an input energy of ~350 μJ. The synthesized aluminum nanoparticles exhibited a surface plasmon resonance peak at ~340 nm. Scanning electron microscopy images of Al nanoparticles demonstrated the spherical morphology with an average size of (27 ± 3.6) nm. The formation of smaller spherical Al nanoparticles and the diminished growth could be from the formation of electric double layers on the Al nanoparticles. In addition to spherical aluminum nanoparticles, triangular/pentagonal/hexagonal nanoparticles were also observed in the colloidal solution. Field emission scanning electron microscopy images of ablated Al targets demonstrated laser induced periodic surface structures (LIPSSs), which were the high spatial frequency LIPSSs (HSF-LIPSSs) since their grating period was ~280 nm. Additionally, coarse structures with a period of ~700 nm were observed.     

窄板坯结晶器内连铸工艺参数对钢液流场的影响

Computational simulations and high-temperature measurements of velocities near the surface of a mold were carried out by using the rod deflection method to study the effects of various operating parameters on the flow field in slab continuous casting (CC) molds with narrow widths for the production of automobile exposed panels. Reasonable agreement between the calculated results and measured subsurface velocities of liquid steel was obtained under different operating parameters of the CC process. The simulation results reveal that the flow field in the horizontal plane located 50 mm from the meniscus can be used as the characteristic flow field to optimize the flow field of molten steel in the mold. Increases in casting speed can increase the subsurface velocity of molten steel and shift the position of the vortex core downward in the downward circulation zone. The flow field of liquid steel in a 1040 mm-wide slab CC mold can be improved by an Ar gas flow rate of 7 L·min?1 and casting speed of 1.7 m·min?1. Under the present experimental conditions, the double-roll flow pattern is generally stable at a submerged entry nozzle immersion depth of 170 mm.     

电渣重熔脱硫技术研究进展

Electroslag remelting (ESR) gives a combination of liquid metal refining and solidification structure control. One of the typical aspects of liquid metal refining during ESR for the advanced steel and alloy production is desulfurization. It involves two patterns, i.e., slag–metal reaction and gas–slag reaction (gasifying desulfurization). In this paper, the advances in desulfurization practices of ESR are reviewed. The effects of processing parameters, including the initial sulfur level of consumable electrode, remelting atmosphere, deoxidation schemes of ESR, slag composition, melting rate, and electrical parameters on the desulfurization in ESR are assessed. The interrelation between desulfurization and sulfide inclusion evolution during ESR is discussed, and advancements in the production of sulfur-bearing steel at a high-sulfur level during ESR are described. The remaining challenges for future work are also proposed.     

Mineral transition and formation mechanism of calcium aluminate compounds in CaO?Al2O3?Na2O system during high-temperature sintering

The mineral transition and formation mechanism of calcium aluminate compounds in CaO?Al₂O₃?Na₂O system during the high-temperature sintering process were systematically investigated using DSC?TG, XRD, SEM?EDS, FTIR, and Raman spectra, and the crystal structure of Na₄Ca₃(AlO₂)₁₀ was also simulated by Material Studio software. The results indicated that the minerals formed during the sintering process included Na₄Ca₃(AlO₂)₁₀, CaO·Al₂O₃, and 12CaO·7Al₂O₃, and the content of Na₄Ca₃(AlO₂)₁₀ could reach 92wt% when sintered at 1200°C for 30 min. The main formation stage of Na₄Ca₃(AlO₂)₁₀ occurred at temperatures from 970 to 1100°C, and the content could reach 82wt% when the reaction temperature increased to 1100°C. The crystal system of Na₄Ca₃(AlO₂)₁₀ was tetragonal, and the cells preferred to grow along crystal planes (110) and (210). The formation of Na₄Ca₃(AlO₂)₁₀ was an exothermic reaction that followed a secondary reaction model, and its activation energy was 223.97 kJ/mol.     

含细夹层的分矿充填层中流动特性的可视化

Ore particles, especially fine interlayers, commonly segregate in heap stacking, leading to undesirable flow paths and changeable flow velocity fields of packed beds. Computed tomography (CT), COMSOL Multiphysics, and MATLAB were utilized to quantify pore structures and visualize flow behavior inside packed beds with segregated fine interlayers. The formation of fine interlayers was accompanied with the segregation of particles in packed beds. Fine particles reached the upper position of the packed beds during stacking. CT revealed that the average porosity of fine interlayers (24.21%) was significantly lower than that of the heap packed by coarse ores (37.42%), which directly affected the formation of flow paths. Specifically, the potential flow paths in the internal regions of fine interlayers were undeveloped. Fluid flowed and bypassed the fine interlayers and along the sides of the packed beds. Flow velocity also indicated that the flow paths easily gathered in the pore throat where flow velocity (1.8 × 10?5 m/s) suddenly increased. Fluid stagnant regions with a flow velocity lower than 0.2 × 10?5 m/s appeared in flow paths with a large diameter.     

Enhanced microwave absorption properties of rod-shaped Fe2O3/Fe3O4/ MWCNTs composites

A novel type of composite absorber,i.e.Fe_2O_3/Fe_3O_4/MWCNTs composites(0%,1.7%and 5%MWCNTs),with microwave absorption properties was successfully fabricated by a facile hydrothermal method.The preparedα-Fe_2O_3/Fe_3O_4nanoparticles displayed rod-shaped morphology.The complex permittivity and permeability of the Fe_2O_3/Fe_3O_4/MWCNTs composites distinctly increased,furthermore,with the introduction of MWCNTs,the Fe_2O_3/Fe_3O_4/MWCNTs composites exhibited fine microwave absorption performance with strong absorption and wide absorption band.In particular,for Fe_2O_3/Fe_3O_4/1.7%MWCNTs composite with an absorber thickness of 2.5 mm,the reflection loss(RL)reached a minimum of-44.1 d B at 10.4 GHz and the effective absorption bandwidth(RL-10 d B)covered 3.3 GHz.The enhanced microwave absorption performance of the Fe_2O_3/Fe_3O_4/MWCNTs composites was attributed to the high dielectric loss and improved impedance matching which was closely related to the rod-shaped morphology of Fe_2O_3,Fe_3O_4and the introduction of MWCNTs.     

Effect of aluminum oxide on the compressive strength of pellets

Analytical-reagent-grade Al₂O₃ was added to magnetite ore during the process of pelletizing, and the methods of mercury intrusion, scanning electron microscopy, and image processing were used to investigate the effect of Al₂O₃ on the compressive strength of the pellets. The results showed that, as the Al₂O₃ content increased, the compressive strength of the pellets increased slightly and then decreased gradually. When a small amount of Al₂O₃ was added to the pellets, the Al₂O₃ combined with fayalite (2FeO·SiO₂) and the aluminosilicate (2FeO·2Al₂O₃·5SiO₂) was generated, which releases some iron oxide and reduces the inhibition of fayalite to the solid phase of consolidation. When Al₂O₃ increased sequentially, high melting point of Al₂O₃ particles hinder the oxidation of Fe₃O₄ and the recrystallization of Fe2O3, making the internal porosity of the pellets increase, which leads to the decrease in compressive strength of the pellets.     

Highly sensitive ZnO nanoparticles-loaded In2O3 hollow microsphere for detecting ppb-level NO2 at low working temperature

This paper presents a NO₂ sensor operating at low temperature, which was fabricated by ZnO nanoparticles-loaded In₂O₃ hollow microspheres composites. SEM, XRD, XPS and HRTEM were executed to determine the morphology and microstructure of ZnO–In₂O₃. The sensing performance of pure In₂O₃ and ZnO–In₂O₃ composite sensors was tested. The NO₂ sensing properties of the composite were greatly improved in contrast with the pure In₂O₃ sensor at the optimized operating temperature (75 °C). ZnO–In₂O₃ composite sensor exhibited an obviously higher response (805.2 for 100 ppb NO₂) than that of the pure In₂O₃ sensor (14 for 100 ppb NO₂). In particular, the response/recovery rate of ZnO–In₂O₃ composite sensor was greatly improved in contrast with the pure In₂O₃ sensor. The n-n heterojunctions created at ZnO–In₂O₃ interfaces improved the sensing performance.     

纳米Al2O3颗粒对Cu-Al2O3性能的影响

采用溶胶-凝胶法制备纳米Al₂O₃颗粒,通过粉末冶金法制备氧化铝铜（Cu-Al₂O₃）。采用X射线光电子能谱仪、扫描电子显微镜、洛氏硬度仪和涡流计分别测试了Cu-Al₂O₃的结合能、微观组织、硬度和导电率。结果表明：随Al₂O₃颗粒含量的增加,Cu-Al₂O₃的硬度先升高后降低,当Al₂O₃颗粒的质量分数达到0.084%时,Cu-Al₂O₃的硬度达到最大值75.73（HRB）。Cu-Al₂O₃的导电率随着Al₂O₃颗粒含量的增加逐渐下降。Al₂O₃颗粒的质量分数为0.084%时为最佳值,Cu-Al₂O₃的硬度达到最大值,导电率达到69.1% IACS。     

Electrical conductivity optimization of the Na3AlF6-Al2O3-Sm2O3 molten salts system for Al-Sm intermediate binary alloy production

Metal Sm has been widely used in making Al-Sm magnet alloy materials. Conventional distillation technology to produce Sm has the disadvantages of low productivity, high costs, and pollution generation. The objective of this study was to develop a molten salt electrolyte system to produce Al-Sm alloy directly, with focus on the electrical conductivity and optimal operating conditions to minimize the energy consumption. The continuously varying cell constant (CVCC) technique was used to measure the conductivity for the Na₃AlF₆-AlF₃-LiF-MgF₂-Al₂O₃-Sm₂O₃ electrolysis medium in the temperature range from 905 to 1055℃. The temperature (t) and the addition of Al₂O₃ (W(Al₂O₃)), Sm₂O₃ (W(Sm₂O₃)), and a combination of Al₂O₃ and Sm₂O₃ into the basic fluoride system were examined with respect to their effects on the conductivity (κ) and activation energy. The experimental results showed that the molten electrolyte conductivity increases with increasing temperature (t) and decreases with the addition of Al₂O₃ or Sm₂O₃ or both. We concluded that the optimal operation conditions for Al-Sm intermediate alloy production in the Na₃AlF₆-AlF₃-LiF-MgF₂-Al₂O₃-Sm₂O₃ system are W(Al₂O₃) + W(Sm₂O₃)=3wt%, W(Al₂O₃):W(Sm₂O₃)=7:3, and a temperature of 965 to 995℃, which results in satisfactory conductivity, low fluoride evaporation losses, and low energy consumption.     

复合氧化物Co3O4/Bi2O3对甲苯的光催化作用

采用微乳法制备复合氧化物Co₃O₄/Bi₂O₃纳米粒子， 用TG-DTA， XRD， XPS和FT-IR对其表征， 以甲苯为气相有机污染物研究Co₃O₄/Bi₂O₃的光催化活性. 结果表明， 微乳法制备的Co₃O₄/Bi₂O₃粒子光催化活性优于纯氧化铋； 活性的提高程度与n(Co) ∶n(Bi)有关， 其最佳配比为0.02 ∶1； 光催化活性随焙烧温度升高而增大, 750 ℃焙烧的样品催化活性最好.     

Mineral-phase evolution and sintering behavior of MO-SiO2-Al2O3-B2O3 (M=Ca,Ba) glass-ceramics by low-temperature liquid-phase sintering

In this work, network former SiO₂ and network intermediate Al₂O₃ were introduced into typical low-melting binary compositions CaO·B₂O₃, CaO·2B₂O₃, and BaO·B₂O₃ via an aqueous solid-state suspension milling route. Accordingly, multiple-phase aluminosilicate glass-ceramics were directly obtained via liquid-phase sintering at temperatures below 950℃. On the basis of liquid-phase sintering theory, mineral-phase evolutions and glass-phase formations were systematically investigated in a wide MO-SiO₂-Al₂O₃-B₂O₃ (M=Ca, Ba) composition range. The results indicate that major mineral phases of the aluminosilicate glass-ceramics are Al₂₀B₄O₃₆, CaAl₂Si₂O₈, and BaAl₂Si₂O₈ and that the glass-ceramic materials are characterized by dense microstructures and excellent dielectric properties.     

Integrated Bi2O3 nanostructure modified with Au nanoparticles for enhanced photocatalytic activity under visible light irradiation

An integrated Bi_2O_3(i-Bi_2O_3) nanostructure with a particle size 10 nm inducing agglomerated structure were synthesized by dissolving bismuth nitrate pentahydrate in diethylene glycol at 180 ℃ with post heat treatment.The prepared i-Bi_2O_3 nanostructures were employed for the construction of Au/i-Bi_2O_3 composite system and characterized by X-ray diffraction pattern,UV-visible diffuse reflectance spectroscopy(DRS),and transmission electron microscopy,X-ray photoemission spectroscopy(XPS) and Energy dispersive X-ray spectroscopy(EDS).The i-Bi_2O_3 nanostructure and Au/i-Bi_2O_3 composite system were found to exhibit high photocatalytic activity than commercial Bi_2O_3 in decomposing salicylic acid under visible light irradiation.The high catalytic activity of i-Bi_2O_3 nanostructure was deduced to be caused by charge separation facilitated by electron hopping between the particles within the integrated structure and space-charge separation between i-Bi_2O_3 and Au.The charge separation behavior in i-Bi_2O_3 nanostructure was further bolstered by comparing the measured.OH radical produced in the solution with i-Bi_2O_3 nanostructure,commercial Bi_2O_3 and Au/i-Bi_2O_3 composite which readily react with 1,4-terephthalic acid(TA) inducing 2-hydroxy terephthalic acid(TAOH) that shows unique fluorescence peak at 426 nm.The space-charge separation between i-Bi_2O_3 and An was confirmed by measuring the electron spin resonance(ESR) spectra.     

高温水热法合成系列介孔氧化铝负载铂催化

采用高温水热法制备稳定、 高度晶化的介孔氧化铝材料(M-Al₂O₃-n), 通过异丙醇铝前驱体与聚四乙烯基吡啶(P4VP)模板间的酸碱自组装实现材料介孔结构的构筑, 再经高温水热处理（180 ℃）实现孔壁的晶化, 并通过担载少量的铂活性组分研究其在催化完全燃烧苯中的性能. 结果表明: M-Al₂O₃-n具有高度晶化的孔壁结构和典型的γ-Al₂O₃晶型; M-Al₂O₃-n具有较大的比表面积（335 m²/g）、 孔容(1.36 cm³/g)和均一的孔径分布（16.1 nm）; M-Al₂O₃-n具有粗糙的表面结构及丰富的纳米多孔结构; 该材料负载少量的铂（质量分数为03%）活性组分得到的新型催化材料在较温和的条件下即可将苯类VOCs完全催化燃烧.     

Phase stability and thermal conductivity of ytterbia and yttria co-doped zirconia

Rare earth oxides doping has been extensively investigated as one of the effective methods to lower thermal conductivity of 4.55 mol% Y2O3stabilized ZrO2(YSZ) thermal barrier coatings(TBCs).In the present work,5–6 mol% Yb2O3and Y2O3co-doped ZrO2ceramics were synthesized by solid reaction sintering at 1600 1C.The phase stability of the samples after heat treatment at 1500 1C was investigated.Yb2O3and Y2O3co-doped zirconia,especially when Yb2O3/Y2O3≥1,contained less monoclinic phase than single Yb2O3or Y2O3phase doped zirconia,indicating that co-doped zirconia was more stable at high temperature than YSZ.The thermal conductivity of the 3 mol% Yb2O3+3 mol% Y2O3co-doped ZrO2was 1.8 W m 1K 1at 1000 1C,which was more than 20% lower than that of YSZ.