An ultra-sensitive non-enzymatic hydrogen peroxide sensor based on SiO2-APTES supported Au nanoparticles modified glassy carbon electrode

A novel electrochemical sensor based on (3-aminopropyl)triethoxysilane (APTES) functionalized SiO₂ supported Au nanoparticles and Nafion (Nf) as the protective membrane was fabricated for the electrochemical determination of H₂O₂ in contact lens-cleaning solution. The modification steps of glassy carbon working electrode (GCE) were evaluated by electrochemical impedance spectroscopy (EIS) and cyclic voltammetry (CV). The amperometric results showed that Nf/[email protected]₂-APTES/GCE sensor can be used to determine H₂O₂ in contact lens solutions with the linear ranges of 14–180 μM and 0.18–7.15 mM, excellent sensitivities of 2514.6 and 894.2 μA mM cm^?2, and a low limit of detection (LOD) of 4.25 μM depending upon signal-to-noise ratio of 3. Nf/[email protected]₂-APTES/GCE exhibited excellent repeatability with relative standard deviation (RDS) of 2.66% and acceptable reproducibility with RSD of 3.35%. The sensor displayed reasonable selectivity in the presence of uric acid, dopamine, ascorbic acid, glucose, mannose, glycine, fructose, histidine, and arginine with RSD less than 2.5%. The fabricated Nf/[email protected]₂-APTES/GCE sensor has been successfully applied to detect H₂O₂ in contact lens cleaning solutions.     

Rational design of carbon shell-encapsulated cobalt nanospheres to enhance microwave absorption performance

Co@C core–shell nanospheres highly dispersed on carbon supports were rationally designed to improve the microwave absorbing property of the composite material, and fabricated by one pot thermal decomposition and simple annealing process. The Co nanospheres were completely encapsulated with thin carbon shells, which can effectively prevent the oxidation of the Co surface. Additionally, the particle size of Co nanospheres were properly controlled to optimize the electromagnetic property of the composite material. As a result, the lightweight Co@C/C composites with the particle size of 20 nm exhibited much enhanced microwave absorption properties. The improved microwave absorption performance is attributed mainly to the enhanced isotropic ratio and impedance matching of magnetic composites via tuning the Co particle size. Therefore, the welldesigned core-shell Co@C composite structure will provide a new insight for the development of high performance microwave absorbers.     

Fabrication and electrochemical properties of 3D nano-network LiFePO_4@multiwalled carbon nanotube composite using risedronic acid as the phosphorus source

LiFePO_4@multiwalled carbon nanotubes(LFP@MWCNTs) nanocomposite has been fabricated using risedronic acid(RDA) as a new eco-friendly phosphorus source. Microscopic, spectroscopic, and electrochemical characterization demonstrate that the MWCNTs are in the form of coiled and cross-linking nanoribbon, which wrapped and encrusted around LiFePO_4 particles to form a three-dimensional(3D) nano-network composite.This microstructure of 3D nano-network is obtained due to the reactions between RDA's special functional groups with Fe~(2+) and C-OH,-C=O or-COOH on the surface of the functionalized MWCNTs. The results also show that the particle size of the fabricated LiFePO_4@MWCNTs composite is below 300 nm with the pure crystal of olivine. This nanocomposite indicates an enhanced reversible capacity of 162.2 mAh g~(-1) at 0.2C, and high capacity retention of 76.5% even at 10C after the 800 th cycles. The electric conductivity and Li~+ diffusion coefficient(D_(Li)~+) of the LiFePO_4@MWCNTs are 3.79 × 10~(-2)S cm~(-1) and 4.46 × 10~(-11) cm~2s~(-1), respectively.These improved electrochemical parameters can be attributed to the nano-sized effect of particles, MWCNTs' wrapping effect and 3D nano-network microstructure of the LFP@MWCNTs resulted from using RDA as a new phosphorus source.     

Rapid point-of-use water purification using nanoscale zero valent iron (nZVI) particles

Nanoscale zero-valent iron (nZVI) particles are increasingly being investigated in removing aqueous contaminants. Here, we have demonstrated its inactivation and magnetic removal of bacteria and endotoxins from environmental wastewater samples. Varying dosages (10–1,000 μL) of 0–6 days aged nZVI with a concentration of 5 mg/mL for 2 mL wastewater samples were tested, and relevant removal efficiencies were determined using culturing method for bacteria and limulus amebocyte lysate (LAL) for endotoxins. The supernatants of wastewater samples after reacting with nZVI and subsequent magnetic separations were subjected to spectroscopic, qPCR and DGGE analysis. Overall, high magnetic bacterial removal efficiencies were observed up to 3–4 logs for 1 mL nZVI, while the removal efficiencies decreased sharply down to 0.5 log for 10 μL nZVI. qPCR and DGGE results revealed that higher dosages of nZVI caused severe bacterial cell membrane ruptures, releasing significant amounts of DNA up to 10⁷–10⁸ gene copies/mL when 1 mL nZVI was used. Richer DGGE patterns were observed for higher nZVI dosages. In addition, regardless of the dosages (10–1,000 μL) we have observed more than 90 % removal of endotoxins from the wastewater samples. The described technology has great promise to be used as a point-of-use water purification solution for various purposes.     

Microstructure/texture evolution maps to optimize hot deformation process of near-α titanium alloy

The microstructure/texture evolution(MTE,for short) map and processing map of a new near a titanium alloy Ti65 were constructed in order to investigate the workability and microstructure evolution of hot deformation.The processing map illustrated four domains,two summit domains and two instability domains.The morphologies of the a phase changed from the spheroidization(α+β region) to the deformed and elongated β grains(near the βtransus temperature T_β),and then to the obvious dynamic recrystallization(DRX)(β region) with the temperature rising from 930 ℃ to 1140℃.Deformation in the α+β field mainly generated the texture component with [0001]or [0223] parallel to radial directions(RDs).While deformation in the β phase field formed two types of texture component with [0001] parallel to RDs and [2110] parallel to compression direction.An optimized processing map was summarized by overlaying the macro-instability map on the original processing map,and the instability domain of Ti65 alloy was confirmed in the area with the strain rate higher than 0.01 s~(-1).     

高腐蚀条件下用铝合金材料腐蚀机理

铝合金具有低密度、低熔点、高比强度及优良的耐腐蚀性能等特点，被广泛用于航空航天、建筑、船舶等领域。在服役过程中，铝合金的表层氧化膜易受到环境中活性阴离子的破坏而发生腐蚀，对其性能造成严重的损害，故研究铝合金在高腐蚀性环境的腐蚀行为对工程选材具有非常重要的指导意义。选择6061铝合金、2195铝锂合金和7075铝合金为研究对象，对其在特定腐蚀介质中的腐蚀过程和力学性能进行分析，研究了铝合金在特定腐蚀介质中腐蚀形貌与力学性能的变化规律。结果表明：腐蚀初期，在高Cl^-、NO₂^3-、SO₂^4-离子浓度的腐蚀环境中，3种铝合金的氧化膜受到阴离子破坏后发生点腐蚀，使基体暴露在腐蚀环境中，进而发生电化学腐蚀，6061铝合金和2195铝锂合金腐蚀方式是由点腐蚀向面腐蚀转变，7075铝合金腐蚀方式为晶间腐蚀；经过腐蚀后6061铝合金能保持稳定的强度和塑性，7075铝合金和2195铝锂合金的强度和塑性都明显降低。     

糖蜜酒精废液脱钾树脂的解吸动力学

【目的】研究糖蜜酒精废液脱钾树脂BK-001中K~+的静态解吸过程。【方法】考察洗脱剂温度、浓度及树脂粒径对K~+解吸过程的影响,用动边界模型描述K~+的解吸过程。【结果】确定糖蜜酒精废液脱钾树脂BK-001中K~+的解吸过程为颗粒扩散控制,该反应的表观活化能为40.9kJ/mol,反应级数为1.19,表观频率因子为5.27×10~4 min~(-1),假二级动力学模型更适合描述K~+的解吸过程(R~20.995)。K+解析过程的总动力学方程式为1-3(1-F)~(2/3)+2(1-F)=5.27×104r20[H2SO4]~(1.19)e_((-4.09×10~4))/RT。【结论】脱钾树脂BK-001的解吸动力学方程为糖蜜酒精废液脱钾树脂的再生及钾盐资源的综合利用提供理论依据。     

毛郁金乙醇提取物降血脂作用研究

【目的】研究毛郁金(Curcuma aromatica)乙醇提取物降血脂作用,为其综合开发利用提供依据。【方法】通过高脂饲料喂养及脂肪乳剂灌胃,建立高脂血症大鼠模型,连续3周给予毛郁金乙醇提取物进行治疗,设正常组、高脂模型组、辛伐他汀组和毛郁金乙醇提取物高、中、低剂量(生药18g·kg-1·d-1,12g·kg-1·d-1,6g·kg-1·d-1)组,以动物实验研究毛郁金乙醇提取物降血脂的作用。【结果】毛郁金乙醇提取物可降低大鼠血清总胆固醇(CHOL)、三酰甘油(TG)和低密度脂蛋白(LDL-C)的含量,并提高血清高密度脂蛋白(HDL-C)含量,对血清CHOL、LDL-C的降低作用:高中低剂量组,中剂量组对降低TG、升高HDL-C含量具有较好作用,毛郁金各给药组均对大鼠血清LDL-C含量有极显著降低作用。【结论】毛郁金乙醇提取物具有明显的降血脂作用。     

Textural changes in metallurgical coke prepared with polyethylene

The effect of high-density polyethylene (HDPE) on the textural features of experimental coke was investigated using polarized-light optical microscopy and wavelet-based image analysis. Metallurgical coke samples were prepared in a laboratory-scale furnace with 2.5%, 5.0%, 7.5%, 10.0%, and 12.5% HDPE by mass, and one sample was prepared by 100% coal. The amounts and distribution of textures (isotropic, mosaic and banded) and pores were obtained. The calculations reveal that the addition of HDPE results in a decrease of mosaic texture and an increase of isotropic texture. Ethylene formed from the decomposition of HDPE is considered as a probable reason for the texture modifications. The approach used in this study can be applied to indirect evaluation for the reactivity and strength of coke.     

南宁至友谊关高速公路边坡植被枯落物特性研究

【目的】了解南宁至友谊关(简称南友)高速公路边坡绿化植被的水文效应。【方法】在全面踏查的基础上,选择了8个不同地点的7种典型群落类型,对其植被枯落物特性进行研究。【结果】三豆混播群落(S4)的枯落物蓄积量、吸水速率、有效拦蓄量均为最佳,分别为43.80t/hm~2、4 227g·kg~(-1)·h~(-1)、55.18t/hm~2,而木豆群落(S1)的枯落物最大持水量、最大持水率最高,分别达到2 832t/hm~2、283.2%。【结论】三豆混播群落是南友高速公路边坡植被类型中水土保持效应最均衡的群落配置,具有良好的生态水源涵养及保持的功能,可推广种植,以维护边坡植被和土壤的水文生态功能。     

Cu-FeOx@AC活化PMS体系除藻效能与机制

为探究富营养化水体中藻类的新型治理技术，通过水热法和高温煅烧法，使颗粒活性炭（AC）表层上负载铜铁双金属氧化物Cu-FeO_x，制得可回收的Cu-FeO_x@AC复合催化剂。以XRD、SEM、FTIR和XPS对Cu-FeO_x@AC的表征为基础，研究Cu-FeO_x占AC的负载比、过一硫酸盐（PMS）使用量、初始pH及不同反应体系对除藻的影响，探究Cu-FeO_x@AC活化过一硫酸盐体系的除藻效能。Cu-FeO_x@AC活化过一硫酸盐体系反应机理，通过自由基淬灭实验、XPS表征进行探究。结果可知，初始pH为6，初始藻细胞密度为1.4×10⁹个/L，使用催化剂0.5 g/L，PMS 0.2 g/L时，反应90 min，该体系对藻的降解率有97.25%。在该体系中，藻细胞能被吸附在Cu-FeO_x@AC复合催化剂表面，在铜、铁不同价态离子的转换及AC的协同作用下，产生空穴、·O2-、·OH、SO4-·，单线态氧等多种氧化基团而被去除。     

龙匙片降血糖作用的实验研究

【目的】龙匙方是广西壮族自治区人民医院俞祝全医生的临床经验方,本文研究其对正常小鼠及几种糖尿病模型小鼠降血糖的作用。【方法】采用链脲佐菌素致糖尿病、肾上腺素致高血糖、大剂量口服葡萄糖致高血糖小鼠模型,分别观察龙匙片对正常和糖尿病模型小鼠血糖的影响。【结果】高、中剂量组(11500mg·kg~(-1)·d~(-1)、5750mg·kg~(-1)·d~(-1))龙匙片对链脲佐菌素致糖尿病、肾上腺素致高血糖、大剂量口服葡萄糖致高血糖小鼠的血糖具有明显的降低作用;但高、低剂量(11500mg·kg~(~(-1))·d~(-1)、3060mg·kg~(-1)·d~(-1))龙匙片对正常小鼠血糖水平均无明显影响(P0.05)。【结论】龙匙片对糖尿病模型小鼠具有降低血糖的作用。     

厄尔尼诺-南方涛动影响下月尺度水文模型参数可移植性

以浙江省3个流域作为研究对象，采用两参数月水量平衡模型（XM模型）和四参数月水量平衡模型（ABCD模型），结合极大似然不确定性估计方法（GLUE）对水文模拟的不确定性区间进行估计，在此基础上，研究不同模型在ENSO（厄尔尼诺-南方涛动）和不同流域地理情况下的参数移植能力。结果表明，厄尔尼诺时期的参数移植至拉尼娜时期，模型模拟效果要略好于拉尼娜时期的参数移植至厄尔尼诺时期；参数少的模型（XM模型）参数移植合格率要优于参数多的模型（ABCD模型）；相邻流域间的参数移植效果要明显优于距离较远的流域；ABCD模型具有更好的空间可参数移植能力。     

污水排海工程渔业资源损害定量分析

【目的】以曹妃甸某污水排海工程为例,对排海工程渔业资源损害定量分析方法进行探讨,为今后类似工程生物资源损害评估提供参考依据。【方法】在大量已有研究成果及经验的基础上,对水污染生物资源损害计算基本公式、受损范围及死亡率的确定方法进行讨论。结合工程实际情况及海洋生态环境现状调查结果,定量分析工程对渔业资源造成的损害。【结果】工程对海洋渔业资源造成损害的面积约为0.218km2,在此范围内,仔鱼和鱼卵的损失量分别约为4.65×106尾和9.63×106个,而成鱼基本不受影响。【结论】本方法的提出对今后海洋工程生物资源损害研究具有一定的参考价值。     

Orbit determination of Chang’E-3 and positioning of the lander and the rover

Chang’E-3 landed on the east of Sinus Iridum area on December 14, 2013, performing China’s first successful soft landing on the lunar surface. We present the results on precision orbit determination and positioning of the lander and the rover. We describe the data, modeling, and methods used to achieve position knowledge over the period December 2–21, 2014. In addition to the radiometric X-band range and Doppler tracking data, delta differential one-way ranging data are also used in the calculation, which show that they strongly improve the accuracy of the orbit reconstruction. Total position overlap differences are about 20 and 30 m for the 100 km × 100 km and 100 km× 15 km lunar orbit, respectively, increased by ~50 % with respect to CE-2 and at the same level as other lunar spacecrafts of recent era such as SELENE and lunar reconnaissance orbiter (LRO). The position error of the soft landing trajectory is less than 100 m. A kinematic statistical method is applied to determine the position of the lander and relative position of the rover with respect to the lander. The position difference of the lander is better than 50 m compared to LRO photograph result. Compared with the delta very long baseline interferometry (VLBI) group delay between the lander and the rover, the delta VLBI phase delay can improve the relative position of the rover from ~1,000 to ~1 m.     

南宁七坡林场尾巨桉人工林生物量的初步研究

【目的】为科学、可持续地经营桉树（Eucalyptus）人工林以及评价桉树人工林在区域碳循环中的地位、作用和生态效益提供有效的依据。【方法】采用平均标准木法和收获法对南宁七坡林场的尾巨桉（Eucalyptus urophylla×E．grandis）及其林下植被的生物量进行调查。【结果】在尾巨桉人工林中,各层次生物量呈现乔木层〉灌木层〉草本层,其中尾巨桉生物量最大,处于主导地位;尾巨桉各器官生物量的大小顺序为树干（64．38％）〉根（24．29％）〉树皮（5．97％）〉老枝（2．25％）〉嫩枝（1．56％）〉老叶（1．32％）〉嫩叶（0．20％）。【结论】尾巨桉的生物量主要集中在树干上,叶的生物量最少。     

鼠尾藻群体的有性生殖力影响因素研究

【目的】研究鼠尾藻(Sargassum thun bergii)有性生殖相关因子间的关系,分析鼠尾藻群体的有性生殖能力。【方法】通过统计分析方法,研究藻体长度与侧枝数、侧枝长度与生殖托数、生殖托长度与生殖托挂卵数间的关系。【结果】藻体长度与侧枝数、侧枝长度与生殖托数、生殖托长度与生殖托挂卵数间都为线性正相关,利用回归方程推算,1株成熟的鼠尾藻藻体能产生2×105~3.3×106个受精卵。【结论】1株成熟鼠尾藻的产卵量基本可满足1m2的采苗生产需要。     

Microstructure evolution and mechanical properties of Ti-8Nb-2Fe-0.2O alloy with high elastic admissible strain for orthopedic implant applications

A Ti-8Nb-2Fe-0.2O(wt.%) alloy with high strength,high elastic admissible strain(δ) and low cost was designed using d-electron theory combined with electron-to-atom ratio(e/a) approach.Interstitial oxygen was introduced to strengthen the matrix of the alloy.The β-solution treated alloy was mainly composed of α " martensite with internal {111}_(α") type Ⅰ nano-twins.The α " martensite with hexagonal-like crystal structure caused by interstitial oxygen showed a high strength of 1.1 GPa but limited ductility.The alloy generated equiaxed fine-grained a phase embedded by β matrix via hot rolling and subsequent annealing in α+β phase field.The obtained alloy indicated a good combination of mechanical properties with ultimate tensile strength,Young's modulus,ductility and δ value of 1029 MPa,74 GPa,21% tensile elongation and 1.32%,respectively.These findings demonstrate that interstitial oxygen and martensitic nano-twins can be used to strengthen the soft α" martensite and high elastic admissible strain can be obtained by formation of equiaxed fine-grained α phase embedded by βmatrix in this Ti-8Nb-2Fe-0.2O alloy for orthopedic implant.