利用氧化基粉煤灰粉和医疗废弃物颗粒开发无电镀镍基复合涂层 (Ni–P/粉煤灰和Ni-P/Ni–P/SiO2–Al2O3)

Recycling and reusing materials from waste have become a nexus in the development of sustainable materials, leading to more balanced technologies. In this study, we developed a composite coating by co-depositing recycled ceramic particles, pulverised fly ash (PFA) and medical ceramics (MC), into a nickel–phosphorus matrix using a typical electroless plating process. Scanning electron microscopy (SEM) images indicated well-dispersed particles in the Ni–P matrix. However, compared with the MC particles, the PFA particles were distributed scantily with a lower content in the matrix, which could be due to the less impingement effect during the co-deposition. A modified microstructure with refined grains was obtained for the PFA-incorporated composite coating, as seen in the SEM micrograph. The X-ray diffraction result of the MC-incorporated composite coating showed the formation of Ni_xSi_y phases in addition to the typical Ni₃P phases for the heat-treated electroless Ni–P coatings. Upon heat treatment, the PFA-reinforced composite coating, due to a modified microstructure, exhibited a higher microhardness up to HK_0.05 818, which is comparable to that of the traditional SiC particle-embedded composite coating (HK_0.05 825). The findings can potentially open up a new strategy to further advance the green approach for industrial surface engineering.     

Preparation of electroless Ni–P composite coatings containing nano-scattered alumina in presence of polymeric surfactant

Ni–P electroless coating was applied on low carbon steel with the incorporation of different amounts of nano Al2O3 powder (ranging from 3 g/l to 30 g/l) in electroless bath. Corrosion properties and microstructures of the coating were studied. The dispersion stability of alumina colloidal particles stabilized by polymeric (non-ionic) surfactants in an electroless bath was also investigated. The surface morphology and the relevant structure were evaluated by scanning electron microscopy (SEM) and X-ray diffraction (XRD). Corrosion behavior of the coated steel was evaluated by electrochemical impedance spectroscopy (EIS) and polarization techniques. The results showed that increasing alumina concentration not only changed the surface morphology, but also promoted the corrosion resistance. Addition of surfactants has an indirect effect on the amount of the incorporated particles. Meanwhile, in the presence of surfactant, corrosion resistance of Ni–P coating containing even a small quantity of alumina was improved since a stabilized bath was obtained.     

Microstructure of Ni–Al powder and Ni–Al composite coatings prepared by twin-wire arc spraying

Ni–Al powder and Ni–Al composite coatings were fabricated by twin-wire arc spraying (TWAS). The microstructures of Ni-5wt%Al powder and Ni-20wt%Al powder were characterized by scanning electronic microscopy (SEM) and energy dispersive spectroscopy (EDS). The results showed that the obtained particle size ranged from 5 to 50 μm. The morphology of the Ni–Al powder showed that molten particles were composed of Ni solid solution, NiAl, Ni₃Al, Al₂O₃, and NiO. The Ni–Al phase and a small amount of Al₂O₃ particles changed the composition of the coating. The microstructures of the twin-wire-arc-sprayed Ni–Al composite coatings were characterized by SEM, EDS, X-ray diffraction (XRD), and transmission electron microscopy (TEM). The results showed that the main phase of the Ni-5wt%Al coating consisted of Ni solid solution and NiAl in addition to a small amount of Al₂O₃. The main phase of the Ni-20wt%Al coating mainly consisted of Ni solid solution, NiAl, and Ni₃Al in addition to a small amount of Al and Al₂O₃, and NiAl and Ni₃Al intermetallic compounds effectively further improved the final wear property of the coatings. TEM analysis indicated that fine spherical NiAl₃ precipitates and a Ni–Al–O amorphous phase formed in the matrix of the Ni solid solution in the original state.     

Corrosion behavior of Ni–P/nano-TiC composite coating prepared in electroless baths containing different types of surfactant

In current research, in order to enhance the incorporation of nano-sized TiC particles into electroless Ni–P (EN) coating, different types of surfactant (cationic, anionic, and polymeric) were added to the plating bath. The effects of addition of the surfactants on surface morphology, deposition rate, TiC and P contents of the prepared coatings were investigated. The surface morphology was evaluated by scanning electron microscopy (SEM). It was demonstrated that in the presence of the anionic, polymeric and somehow cationic surfactants, TiC nano-particles were embedded in the matrix which influenced the surface morphology. The effect of surfactant types on the corrosion properties of Ni–P/TiC coated steel was also studied. Corrosion behavior of the coated steel was evaluated by potentiodynamic polarization and electrochemical impedance spectroscopy (EIS) which affected by the incorporation of TiC particles into the Ni–P matrix. The level of corrosion resistance improvement depended largely on the phosphorous and TiC concentration of the applied coating.     

Effect of pickling processes on the microstructure and properties of electroless Ni–P coating on Mg–7.5Li–2Zn–1Y alloy

The electroless plating Ni–P is prepared on the surface of Mg–7.5Li–2Zn–1Y alloys with different pickling processes.The microstructure and properties of Ni–P coating are investigated.The results show that the Ni–P coatings deposited using the different pickling processes have a different high phosphorus content amorphous Ni–P solid solution structure,and the Ni–P coatings exhibit higher hardness.There is higher phosphorus content of Ni–P amorphous coating using 125 g/L Cr O3and 110 ml/L HNO3(w68%)than using 180 g/L Cr O3and 1 g/L KF during pre-treatment,and the coating structure is more compact,and the Ni–P coatings exhibit more excellent adhesion with substrate(Fcup to22 N).The corrosion potential of Ni–P coating is improved and exhibits good corrosion resistance.As a result,Mg-7.5Li-2Zn-1Y alloy is remarkably protected by the Ni–P coating.     

Fabrication of Fe–TiC–Al2O3 composites on the surface of steel using a TiO2–Al–C–Fe combustion reaction induced by gas tungsten arc cladding

The aim of the present study was to fabricate Fe–TiC–Al₂O₃ composites on the surface of medium carbon steel. For this purpose, TiO₂–3C and 3TiO₂–4Al–3C–xFe (0 ≤ x ≤ 4.6 by mole) mixtures were pre-placed on the surface of a medium carbon steel plate. The mixtures and substrate were then melted using a gas tungsten arc cladding process. The results show that the martensite forms in the layer produced by the TiO₂–3C mixture. However, ferrite–Fe₃C–TiC phases are the main phases in the microstructure of the clad layer produced by the 3TiO₂–4Al–3C mixture. The addition of Fe to the TiO₂–4Al–3C reactants with the content from 0 to 20wt% increases the volume fraction of particles, and a composite containing approximately 9vol% TiC and Al₂O₃ particles forms. This composite substantially improves the substrate hardness. The mechanism by which Fe particles enhance the TiC + Al₂O₃ volume fraction in the composite is determined.     

Electroplating of Ni/Co–pumice multilayer nanocomposite coatings: Effect of current density on crystal texture transformations and corrosion behavior

The present paper aims to investigate the influence of the current density in the electroplating process on the microstructure, crystal texture transformations, and corrosion behavior of Ni/Co-pumice multilayer nanocomposite coatings. The Ni/Co-pumice composite coatings were prepared by deposition of Ni, followed by the simultaneous deposition of pumice nanoparticles (NPs) in a Co matrix via an electroplating process at various current densities. Afterward, the morphology, size, topography, and crystal texture of the obtained samples were investigated. Furthermore, electrochemical methods were used to investigate the corrosion behavior of the produced coatings in a solution of 3.5wt% NaCl. The results indicated that increasing the plating current density changed the mechanism of coating growth from the cell state to the column state, increased the coating thickness, roughness, and texture coefficient (TC) of the Co (203) plane, and reduced the amount of pumice NPs incorporated into the Ni/Co-pumice composite. The electrochemical results also indicated that increasing the current density enhanced the corrosion resistance of the Ni/Co-pumice composite.     

Preparation of in situ and ex situ reinforced Fe–10Cr–1Cu–1Ni–1Mo–2C containing NbC particles by milling and hot pressing

An in situ and ex situ reinforced powder metallurgy(PM) steel was prepared by the combination of high-energy ball milling and subsequent hot pressing of elemental mixed powders of Fe–10Cr–1Cu–1Ni–1Mo–2C by mass with the addition of Nb C particles. A 40-h milling pretreatment makes the powder particles nearly equiaxed with an average diameter of ~8 μm, and the ferrite grain size is refined to ~6 nm. The sintered density reaches 99.0%–99.7% of the theoretical value when the sintering is conducted at temperatures greater than 1000°C for 30 min. In the sintered bulk specimens, the formation of an in situ M7C3(M = Cr, Fe, Mo) phase is confirmed. M7C3 carbides with several hundred nanometers in size are uniformly distributed in the matrix. Some ultra-fine second phases of 50–200 nm form around the ex situ Nb C and in situ M7C3 particles. The sintered steel exhibits an excellent combination of hardness( Hv 500) and compressive strength(2100–2420 MPa).     

Microstructure and properties of Cu–Ti–Ni alloys

The effects of Ni addition and aging treatments on the microstructure and properties of a Cu–3Ti alloy were investigated. The microstructure and precipitation phases were characterized by X-ray diffraction, scanning electron microscopy, and transmission electron microscopy; the hardness, electrical conductivity, and elastic modulus of the resulting alloys were also tested. The results show that Ni addition increases the electrical conductivity and elastic modulus, but decreases the hardness of the aged Cu–3Ti alloy. Within the range of the experimentally investigated parameters, the optimal two-stage aging treatment for the Cu–3Ti–1Ni and Cu–3Ti–5Ni alloy was 300°C for 2 h and 450°C for 7 h. The hardness, electrical conductivity, and elastic modulus of the Cu–3Ti–1Ni alloy were HV 205, 18.2% IACS, and 146 GPa, respectively, whereas the hardness, electrical conductivity, and elastic modulus of the Cu–3Ti–5Ni alloy were HV 187, 31.32% IACS, and 147 GPa, respectively. Microstructural analyses revealed that β′-Ni3 Ti and β′-Cu4 Ti precipitate from the Cu matrix during aging of the Cu–3Ti–5Ni alloy and that some residual Ni Ti phase remains. The increased electrical conductivity is ascribed to the formation of Ni Ti, β′-Ni3 Ti, and β′-Cu4 Ti phases.     

Microstructure and wear resistance of PTA clad Cr_7C_3/γ-Fe ceramal composite coating

A wear resistant Cr7C3/γ-Fe ceramal composite coating was fabricated on substrate of the hardening and tempering C degree steel by PTA (plasma transferred arc) cladding with (wt%) Fe-25Cr-7C elemental powder blends. Microstructure of the coating was characterized by OM, SEM, XRD and EDS. Wear resistance of the coating was tested under dry sliding wear condition at room temperature. The results indicate that the PTA clad ceramal composite coating has a rapidly solidified fine microstructure consisting of Cr7C3 primary particles uniformly distributed in theγ-Fe matrix and is metallurgically bonded to the C degree steel substrate. The PTA clad Cr7C3/γ-Fe ceramal composite coating has high hardness and excellent wear resistance under dry sliding wear test conditions. The excellent wear resistance of the Cr7C3/γ-Fe ceramal composite coating is attributed to the coating's high hardness, strong covalent atomic bonding and refined microstructure.     

Effect of Y_2O_3 content in the pack mixtures on microstructure and oxidation resistance of B–Y modified silicide coating

B–Y modified silicide coatings were prepared on Nb–Si based alloy by pack cementation at 1300 ℃ for 10 h. The effect of Y_2O_3 content in the pack mixtures on microstructure and oxidation resistance of the coatings was investigated. The results show that the four coatings have similar structures, which possess a(Nb,X)Si_2 outer layer and a(Nb,X)_5Si_3 transitional layer. Y_2O_3 content in the pack mixtures has an obvious effect on the Si content in the coating. The mass gains of the coatings prepared with 0.5, 1, 2 and 3 wt% Y_2O_3 in pack mixtures are 2.33, 1.96, 2.05 and 2.86 mg/cm~2 after oxidation at 1250 ℃ for 100 h, respectively. The coating prepared with 1 wt% Y_2O_3 exhibits the best oxidation resistance due to the formation of a dense glass-like borosilicate scale.     

Growth in solution of hooked Ni–Fe fibers by oriented rotation and attachment approaches

Inspired by the curved branches of fractal trees, hooked Ni–Fe fibers were grown in situ in Ni–Fe composite coatings on a spheroidal graphite cast iron substrate. These hooked Ni–Fe fibers exhibited inclination angles of about 39°, which was in accordance with the theoretical prediction of 37°. Ni–Fe nanostructures self-assembled to form dendrites and evolved into hooked fibers by an oriented attachment reaction. The orientation rotation of Ni–Fe nanostructures played an important role in the growth of curved hooked Ni–Fe fibers. During sliding wear tests, the volume loss of the spheroidal graphite cast iron substrate was 2.2 times as large as that of the Ni–Fe coating reinforced by hooked fibers. The good load-transferring ability of hooked Ni–Fe fibers led to an improvement in their wear properties during wear tests.     

In situ(α-Al_2O_3+ZrB_2)/Al composites with network distribution fabricated by reaction hot pressing

In situ(α-Al_2O_3+ZrB_2)/Al composites with network distribution were fabricated using low-energy ball milling and reaction hot pressing. Differential thermal analysis(DTA) was used to study the reaction mechanisms in the Al–Zr O2–B system. X-ray diffraction(XRD) and scanning electron microscopy(SEM) in conjunction with energy-dispersive X-ray spectroscopy(EDX) were used to investigate the composite phases, morphology, and microstructure of the composites. The effect of matrix network size on the microstructure and mechanical properties was investigated. The results show that the optimum sintering parameters to complete reactions in the Al–Zr O2–B system are 850°C and 60 min. In situ-synthesized α-Al2O3 and Zr B2 particles are dispersed uniformly around Al particles, forming a network microstructure; the diameters of the α-Al2O3 and Zr B2 particles are approximately 1–3 μm. When the size of Al powder increases from 60–110 μm to 150–300 μm, the overall surface contact between Al powders and reactants decreases, thereby increasing the local volume fraction of reinforcements from 12% to 21%. This increase of the local volume leads to a significant increase in microhardness of the in situ(α-Al2O3–Zr B2)/Al composites from Hv 163 to Hv 251.     

Synthesis, characterization and antibacterial activity of copper, nickel and bimetallic Cu– Ni nanoparticles for potential use in dental materials

The antibacterial effect is a desirable property in dental materials.Development of simple methods for the preparation of nanosized metal particles has attracted significant attention because of their future applications due to unusual size-dependent antibacterial properties.Copper(Cu),Nickel(Ni) and bimetallic Cu–Ni nanoparticles were prepared by a simple chemical method and their antibacterial activity was tested against the widely used standard human pathogens Staphylococcus aureus(gram-negative) and Escherichia coli(gram-positive).Additionally,these nanoparticles were tested against the dental pathogen Streptococcus mutans.Our results are promising for potential use in dental materials science.     

HOVF喷涂Ni–22Cr–10Al–1Y 和Ni–22Cr–10Al–1Y–SiC (N)涂层对ASTM-SA213-T22钢组织和热腐蚀行为的影响

The present paper deals with the investigation of microstructure and high-temperature hot corrosion behavior of high-velocity oxy fuel (HVOF)-produced coatings. Two powder coating compositions, namely, Ni22Cr10Al1Y alloy powder and Ni22Cr10Al1Y (80wt%; micro-sized)–silicon carbide (SiC) (20wt%; nano (N)) powder, were deposited on a T-22 boiler tube steel. The hot corrosion behavior of bare and coated steels was tested at 900°C for 50 cycles in Na₂SO₄–60wt%V₂O₅ molten-salt environment. The kinetics of corrosion was established with weight change measurements after each cycle. The microporosity and microhardness of the as-coated samples have been reported. The X-ray diffraction, field emission-scanning electron microscopy/energy dispersive spectroscopy, and X-ray mapping characterization techniques have been utilized for structural analysis of the as-coated and hot-corroded samples. The results showed that both coatings were deposited with a porosity less than 2%. Both coated samples revealed the development of harder surfaces than the substrate. During hot corrosion testing, the bare T22 steel showed an accelerated corrosion in comparison with its coated counterparts. The HVOF-sprayed coatings were befitted effectively by maintaining their adherence during testing. The Ni22Cr10Al1Y–20wt%SiC (N) composite coating was more effective than the Ni–22Cr–10Al–1Y coating against corrosion in the high-temperature fluxing process.     

Microstructure characteristics of Ni/WC composite cladding coatings

A multilayer tungsten carbide particle (WCp)-reinforced Ni-based alloy coating was fabricated on a steel substrate using vacuum cladding technology. The morphology, microstructure, and formation mechanism of the coating were studied and discussed in different zones. The microstructure morphology and phase composition were investigated by scanning electron microscopy, optical microscopy, X-ray diffraction, and energy-dispersive X-ray spectroscopy. In the results, the coating presents a dense and homogeneous microstructure with few pores and is free from cracks. The whole coating shows a multilayer structure, including composite, transition, fusion, and diffusion-affected layers. Metallurgical bonding was achieved between the coating and substrate because of the formation of the fusion and diffusion-affected layers. The Ni-based alloy is mainly composed of γ-Ni solid solution with finely dispersed Cr₇C₃/Cr₂₃C₆, CrB, and Ni+Ni₃Si. WC particles in the composite layer distribute evenly in areas among initial Ni-based alloying particles, forming a special three-dimensional reticular microstructure. The macrohardness of the coating is HRC 55, which is remarkably improved compared to that of the substrate. The microhardness increases gradually from the substrate to the composite zone, whereas the microhardness remains almost unchanged in the transition and composite zones.     

Microstructural analysis and hot corrosion behavior of HVOF-sprayed Ni–22Cr–10Al–1Y and Ni–22Cr–10Al–1Y–SiC(N) coatings on ASTM-SA213-T22 steel

The present paper deals with the investigation of microstructure and high-temperature hot corrosion behavior of high-velocity oxy fuel(HVOF)-produced coatings. Two powder coating compositions, namely, Ni22Cr10Al1Y alloy powder and Ni22Cr10Al1Y(80 wt%; microsized)–silicon carbide(SiC)(20 wt%; nano(N)) powder, were deposited on a T-22 boiler tube steel. The hot corrosion behavior of bare and coated steels was tested at 900°C for 50 cycles in Na_2SO_4–60 wt%V_2O_5 molten-salt environment. The kinetics of corrosion was established with weight change measurements after each cycle. The microporosity and microhardness of the as-coated samples have been reported. The X-ray diffraction,field emission-scanning electron microscopy/energy dispersive spectroscopy, and X-ray mapping characterization techniques have been utilized for structural analysis of the as-coated and hot-corroded samples. The results showed that both coatings were deposited with a porosity less than2%. Both coated samples revealed the development of harder surfaces than the substrate. During hot corrosion testing, the bare T22 steel showed an accelerated corrosion in comparison with its coated counterparts. The HVOF-sprayed coatings were befitted effectively by maintaining their adherence during testing. The Ni22Cr10Al1Y–20 wt%SiC(N) composite coating was more effective than the Ni–22Cr–10Al–1Y coating against corrosion in the high-temperature fluxing process.     

Effect of Ni content on the wear behavior of Al–Si–Cu–Mg–Ni/SiC particles composites

In recent years, the addition of Ni has been widely acknowledged to be capable of enhancing the mechanical properties of Al–Si alloys. However, the effect of Ni on the wear behaviors of Al–Si alloys and Al matrix composites, particularly at elevated temperatures, remains an understudied area. In this study, Al–Si–Cu–Mg–Ni/20wt% SiC particles(SiCp) composites with varying Ni contents were prepared by using a semisolid stir casting method. The effect of Ni content on the dry sliding wear behavior ...     

Fabrication and character ization of electrospun TiO2/CuS micro–nano-scaled composite fibers

A process to fabricate a kind of novel micro–nano scaled TiO2/CuS composite fibers by electrospinning technique and chemical precipitation method was developed in the present study. The microstructures and photoelectronic properties of the fibers were characterize d using SEM, FT-IR, UV–vis and fluorescence spectroscopy. The results revealed that the TiO2 portion in the composite fibers was a mixture rutile and anatase phases while TiO2 and CuS had been fully composite. The fibers had smooth surface with a diameter of 50–300 nm. Comparing with pure TiO2 fiber, the TiO2/CuS micro–nano-scaled composite fibers exhibited a strong absorption in the visible light region and the efficiency of photo-induced charge separation were enhanced. This composite system is of widely potential applications in the areas such as solar cells, supercapacity, photocatalysis, etc.     

Effect of heat treatment on the microstructure of a Ni–Fe based superalloy for advanced ultra-supercritical power plant applications

The effect of heat treatment on the microstructure and microhardness of a Ni–Fe based superalloy for700 °C advanced ultra-supercritical coalfi red power plants was investigated. Results showed that the main phases in the alloy were γ, γ′, MC and M_23C_6, and no harmful phase was observed in the alloy.M_23C_6-type carbides discretely distributed nearby grain boundaries as the alloy was aged at above840 °C. The microhardness decreased with increasing aging temperature. The coarsening of γ′ led to the increment of microhardness at 780 °C and 810 °C for a short aging time, and a signi fi cant decrease in microhardness after aging at 840 °C. The aging temperature had more signi fi cant role on the microstructure than holding time. Therefore, to obtain optimum strengthening effect for this alloy, the aging temperature should not exceed 810 °C.