Photoluminescence and cathodoluminescence properties of a novel CaLaGa307：Dy3＋ phosphor

A single host white emitting phosphor, CaLaGa3O7:Dy3+, was synthesized by chemical co-precipitation. Field emission scanning electron microscopy, X-ray diffraction, laser particle size analysis, and photoluminescence and cathodoluminescence spectra were used to investigate the structural and optical properties of the phosphor. The phosphor particles were composed of microspheres with a slight tendency to agglomerate, and an average diameter was of about 1.0 μm. The Dy3+ ions acted as luminescent centers, and substituted La3+ ions in the single crystal lattice of CaLaGa3O7 where they were located in Cs sites. Under excitation with ultraviolet light and a low voltage electron beam, the CaLaGa3O7:Dy3+ phosphor exhibited the characteristic emission of Dy3+ (4F9/2-6H15/2 and 4F9/2-6H13/2 transitions) with intense yellow emission at about 573 nm. The chromaticity coordinates for the phosphor were in the white region. The relevant luminescence mechanisms of the phosphor are investigated. This phosphor may be applied in both field emission displays and white light-emitting diodes.     

Synthesis and modification of well-ordered layered cathode oxide LiNi<Subscript>2/3</Subscript>Mn<Subscript>1/3</Subscript>O<Subscript>2</Subscript>

Oxalic-acid-based co-precipitation method was employed to prepare LiNi_2/3Mn_1/3O₂ sample with a high-ordered structure. Li⁺, Ni²⁺ and Mn²⁺ acetates were used as starting materials. The influence of the amount of lithium source in the starting materials on Li⁺ content, disorder of Li⁺-Ni²⁺ ions, and electrochemical performance has been investigated. Rietveld refinement shows that the sample prepared with 20% excess Li-source in the starting materials exhibits a perfect ordered structure. A specific discharge capacity is as high as 172 mAh/g at C/20 in the voltage range of 4.35–2.7 V. However, the cyclability is not satisfactory: about 25.3% fade in capacity was observed over 50 cycles. Chemically stable SiO2 was coated on the surface of LiNi_2/3Mn_1/3O₂ particles. A significant improvement in cyclability was attained with 3 wt% SiO2 coating, which is ascribable to the protection of LiNi_2/3Mn_1/3O₂ particles from being dissolved into the electrolyte.     

Up-conversion luminescence of Er^3＋ doped and Er^3＋/Yb^3＋ co-doped YTaO4

The synthesis and up-conversion luminescent properties of YTaO4：Er^3＋ and YTaO4：Er^3＋/Yb^3＋ are reported for the first time. According to the measurement results of up-conversion spectra, Yb^3＋ co-doping can remarkably enhance the green （^2H11/2/^4S3/2→^4I15/2） and red （^4F9/2→^4I15/2） emissions, but depress the infrared emission （^4I9/2→^4I15/2）. With the increase of the Yb^3＋ concentration, the intensity of green emission increases, after that, when the Yb^3＋ concentration increases continuously, the intensity of green emission decreases, while those of the red and infrared emissions increase and decrease alternately. In addition, the up-conversion mechanisms of Er^3＋ doped and Er^3＋/Yb^3＋ co-doped YTaO4 are also discussed. It is found that the transform of up-conversion mechanism from two-step energy transfer to cooperating sensitization takes place when Yb^3＋ concentration is increased up to 12 mol%. With the further increase of Yb^3＋ concentration, the energy-back-transfer gradually becomes the dominant up-conversion mechanism, which results in the quenching of the green emission and slight increasing of the red and infrared emissions.     

Photoluminescence and cathodoluminescence properties of CaLaGa<Subscript>3</Subscript>O<Subscript>7</Subscript>:Eu<Superscript>3+</Superscript> phosphors

The CaLaGa₃O₇:Eu³⁺ phosphor was prepared by a chemical co-precipitation method. Field emission scanning electron microscopy (FE-SEM), laser particle size analysis, X-ray diffraction (XRD), photoluminescence (PL), and cathodoluminescence (CL) spectra were utilized to characterize the synthesized phosphor. The results revealed that the phosphor was composed of microspheres with a slight agglomerate phenomenon and was spherically shaped. The average grain size was about 1.0 μm. Eu³⁺ ions, as luminescent centers, substituted La³⁺ ions into the single crystal lattice of CaLaGa₃O₇ with the sites of C_s. Although the CL spectrum was greatly different from the PL spectrum, it had the strongest red emission corresponding to the ⁵D₀ →⁷F₂ transition of Eu³⁺. Under the excitation of UV light (287 nm) and electron beams (1.0–7.0 kV), the chromaticity coordinates of the phosphor were found to be in the nearly red and orange light regions, respectively.     

Effects of Yb^3＋ codoping on visible and near infrared emissions of Er^3＋-Yb^3＋ codoped Al2O3 powders by the sol-gel method

The 0.1 mol% Er^3＋ and 0-2 mol% Yb^3＋ codoped Al2O3 powders were prepared by the sol-gel method, and the phase structure, including only two crystalline types of doped Al2O3 phase, γ-（Al,Er, Yb）2O3 and θ-（Al,Er, Yb）2O3, was detected at the sintering temperature of 1000℃. The visible and near infrared emissions properties depended strongly on the Yb^3＋ codoping, and the corresponding maximal peak intensities centered at about 523, 545, 660 and 1533 nm were obtained respectively for the 0.1 mol% Er^3＋ and 0.5 mol% Yb^3＋ codoped Al2O3 powders, which were composed of θ-（Al,Er,Yb）2O3 and a small amount of γ-（Al,Er, Yb）2O3 phases. The two-photon absorption process was responsible for the visible up-conversion emissions, and the one-photon absorption process was involved in the near infrared emissions of the Er^3＋-yb^3＋ codoped Al2O3 powders.     

Molecular simulation study of the binding mechanism of [α-PTi<Subscript>2</Subscript>W<Subscript>10</Subscript>O<Subscript>40</Subscript>]<Superscript>7−</Superscript> for its promising broad-spectrum inhibitory activity to FluV-A neuraminidase

Polyoxometalate (POM) has promising antiviral activities. It shows broad-spectrum inhibiting ability, high efficiency, and low tox-icity. Experimental assays show that titanium containing polyoxotungstates have anti-influenza-virus activity. In this paper, the bind-ing mechanisms of five isomers of di-Ti-substituted polyoxotungstate, [α-1,2-PTi₂W₁₀O₄₀]^7– (α-1,2), [α-1,6-PTi₂W₁₀O₄₀]^7– (α-1,6), [α-1,5-PTi₂W₁₀O₄₀]^7– (α-1,5), [α-1,4-PTi₂W₁₀O₄₀]^7– (α-1,4) and [α-1,11-PTi₂W₁₀O₄₀]^7– (α-1,11), to five subtypes of influenza virus A neuraminidase (FluV-A NA) were investigated in the context of aqueous solution by using molecular docking and molecular dynamics studies. The results show that the isomer α-1,2 is superior to other isomers as a potential inhibitor to neuraminidase. The positively charged arginine residues around the active site of NA could be induced by negatively charged POM to adapt themselves and could form salt bridge interactions and hydrogen bond interactions with POM. The binding free energies of POM/NA complexes range from –5.36 to –8.31 kcal mol^–1. The electrostatic interactions are found to be the driving force during the binding process of POM to NA. The conformational analysis shows that POM tends to bind primarily with N1 and N8 at the edge of the active pocket, which causes the conformational change of the pincers structure comprising residue 347 and loop 150. Whereas, the active pockets of N2, N9 and N4 are found to be more spacious, which allows POM to enter into the active pockets directly and anchor there firmly. This study shows that negatively charged ligand as POM could induce the reorganization of the active site of NA and highlights POM as a promising inhibitor to NA despite the ever increasing mutants of NA.     

Preparation and luminescence characteristics of Sr3SiO5：Eu^2＋ phosphor for white LED

The Sr3SiO5：Eu^2＋ phosphor was synthesized by high temperature solid-state reaction. The emission spectrum of Sr3SiO5：Eu^2＋ shows two bands centered at 487 and 575 nm, which well agree with the theoretic values of emission spectrum. The excitation spectrum for 575 nm emission center has several excitation bands at 365, 418, 458 and 473 nm. And the results show that the emission spectrum of Sr3SiO5：Eu^2＋ is influenced by the Eu^2＋ concentration. The relative emission spectra of the white-emitting InGaN-based YAG：Ce^3＋ LED and Sr3SiO5：Eu^2＋ LED were investigated. The results show that the color development of InGaN-based Sr3SiO5：Eu^2＋ is better than that of InGaN-based YAG：Ce^3＋, and the CIE chromaticity of InGaN-based Sr3SiO5：Eu^2＋ is （x=0.348, y=0.326）.     

CO<Subscript>2</Subscript> gas emplacement age in the Songliao Basin: Insight from volcanic quartz <Superscript>40</Superscript>Ar-<Superscript>39</Superscript>Ar stepwise crushing

Due to a lack of suitable minerals, the gas/oil emplacement ages have never been accurately obtained before. CH₄-CO₂-saline- bearing secondary inclusions are found in quartz from the volcanic rocks of the Yingcheng Formation, the container rocks of the deep CO₂ gas reservoir in the Songliao Basin. The inclusion fluid was trapped into microcracks in quartz during the gas emplacement and accumulation, providing an optimal target for the ⁴⁰Ar-³⁹Ar stepwise crushing technique to determine the CO₂ gas emplacement age. ⁴⁰Ar-³⁹Ar dating results of a quartz sample by stepwise crushing yield a highly linear-regression isochron with an age of 78.4±1.3 Ma, indicating that the accumulation of the deep CO₂ gas reservoir in the Songliao Basin occurred in the late Cretaceous. This is the first time to report an exact isotopic age for a CO₂ gas reservoir, which indicates that the ⁴⁰Ar-³⁹Ar dating can serve as a new technique to date the oil/gas emplacement ages.     

Near-infrared to visible up-conversion emissions of Er^3＋ doped Al2O3 powders derived from the sol-gel method

The Er3 doped Al2O3 powders were prepared by the sol-gel method using the aluminium isopropoxide [Al(OC3H7)3]-derived Al2O3 sols with addition of the erbium nitrate [Er(NO3)3.5H2O]. The different phase structure, including three crystalline types of (Al,Er)2O3 phases, γ, θ, α, and two Er-Al-O phases, ErAlO3 and Al10Er6O24, was obtained with the 1 mol% Er3 doped Al2O3 powders at the different sintering temperatures of 600―1200℃. The green and red up-conversion emissions centered at about 523, 545 and 660 nm, corresponding respectively to the 2H11/2, 4S3/2→4I15/2 and 4F9/2→4I15/2 transitions of Er3 , were detected by a 978 nm semiconductor laser diodes excitation. The phase structure and OH content had evident influence on the up-conversion emissions intensity. The maximum intensities of both the green and red emissions were obtained respectively for the Er3 doped Al2O3 powders sintered at 1200 ℃, which was composed mainly of α-(Al,Er)2O3, less of ErAlO3 and Al10Er6O24 phases, and with the least OH content. The two-photon absorption up-conversion process was involved in the green and red up-conversion emissions of the Er3 doped Al2O3 powders.     

Theoretical investigations of ESR and optical spectra of crystalline KHSO4：Mn^2＋

Calculations of d-d transitions and the axial zero-field splitting parameter D in crystalline KHSO4:Mn2+ have been undertaken, with consideration of the ninth O2– ligand. Energy level values calculated in a tetragonal field are in good agreement with experimentally observed values. Occasionally degenerate energy levels of 4A1(4Eg(G)) and 4A1(4A1g(G)) were found in the tetragonal crystal field. The calculated value of D is in good agreement with experimental value for KHSO4:Mn2+.     

Electrochemical performance of a nickel-rich LiNi<Subscript>0.6</Subscript>Co<Subscript>0.2</Subscript>Mn<Subscript>0.2</Subscript>O<Subscript>2</Subscript> cathode material for lithium-ion batteries under different cut-off voltages

A spherical-like Ni_0.6Co_0.2Mn_0.2(OH)₂ precursor was tuned homogeneously to synthesize LiNi_0.6Co_0.2Mn_0.2O₂ as a cathode material for lithium-ion batteries. The effects of calcination temperature on the crystal structure, morphology, and the electrochemical performance of the as-prepared LiNi_0.6Co_0.2Mn_0.2O₂ were investigated in detail. The as-prepared material was characterized by X-ray diffraction, scanning electron microscopy, laser particle size analysis, charge-discharge tests, and cyclic voltammetry measurements. The results show that the spherical-like LiNi_0.6Co_0.2Mn_0.2O₂ material obtained by calcination at 900℃ displayed the most significant layered structure among samples calcined at various temperatures, with a particle size of approximately 10 μm. It delivered an initial discharge capacity of 189.2 mAh·g-1 at 0.2C with a capacity retention of 94.0% after 100 cycles between 2.7 and 4.3 V. The as-prepared cathode material also exhibited good rate performance, with a discharge capacity of 119.6 mAh·g-1 at 5C. Furthermore, within the cut-off voltage ranges from 2.7 to 4.3, 4.4, and 4.5 V, the initial discharge capacities of the calcined samples were 170.7, 180.9, and 192.8 mAh·g-1, respectively, at a rate of 1C. The corresponding retentions were 86.8%, 80.3%, and 74.4% after 200 cycles, respectively.     

Heterobimetallic clusters of Na<Subscript>8</Subscript>Ln(O<Superscript>t</Superscript>Bu)<Subscript>10</Subscript>(OH) as homogeneous catalysts for amidation of aldehydes with amines

Heterobimetallic clusters of Na8Ln(O^tBu)₁₀(OH) (Ln = ytterbium, europium, samarium and neodymium) are found to be useful catalysts for amidation of aldehydes with amines under mild conditions. The catalytic activity depends on the central metal ion in the cluster, and the order activity is ytterbium < europium < samarium ≈ neodymium. The catalysts show a wide range of scope in their activity towards amines including aliphatic amines and secondary cyclic amines such as pyrrolidine and piperidine.     

Preparation and upconversion luminescence of YVO<Subscript>4</Subscript>:Er<Subscript>3+</Subscript>, Yb<Subscript>3+</Subscript>

YVO₄:Er³⁺, Yb³⁺ with varying Yb³⁺ concentrations were prepared by a precipitation method. The results of X-ray diffraction (XRD) show that all the samples have a tetragonal zircon structure; the calculated average crystallite sizes are in the range of 14–22 nm. The lattice constants and cell volume of the samples decrease slightly with the increase in Yb³⁺ concentration. The upconversion luminescence spectra of all the samples were studied under 980 nm laser excitation. The strong green emission is observed, which is attributed to the ²H_11/2 → ⁴I_15/2 and ⁴S_3/2→⁴I_15/2 transitions of Er³⁺, and the red emission peaks in 650–675 nm can be ignored. The emission intensity for the sample depends on the Yb³⁺ concentration. These results reveal that the upconversion processes of YVO₄:Er³⁺, Yb³⁺ are related to the structure and the doping Yb³⁺ concentration of the sample.     

Electrochemical properties of LiNi<Subscript>0.5</Subscript>Mn<Subscript>1.3</Subscript>Ti<Subscript>0.2</Subscript>O<Subscript>4</Subscript>/Li<Subscript>4</Subscript>Ti<Subscript>5</Subscript>O<Subscript>12</Subscript> cells

Spinel compounds LiNi_0.5Mn_1.3Ti_0.2O₄ (LNMTO) and Li₄Ti₅O₁₂ (LTO) were synthesized by different methods. The particle sizes of LNMTO and LTO are 0.5–2 and 0.5–0.8 μm, respectively. The LNMTO/LTO cell exhibits better electrochemical properties at both a low current rate of 0.2C and a high current rate of 1C. When the specific capacity was determined based on the mass of the LNMTO cathode, the LNMTO/LTO cell delivered 137 mA·h·g⁻¹ at 0.2C and 118.2 mA·h·g⁻¹ at 1C, and the corresponding capacity retentions after 30 cycles are 88.5% and 92.4%, respectively.     

Effect of CO<Subscript>2</Subscript> and H<Subscript>2</Subscript>O on gasification dissolution and deep reaction of coke

To more comprehensively analyze the effect of CO₂ and H₂O on the gasification dissolution reaction and deep reaction of coke, the reactions of coke with CO₂ and H₂O using high temperature gas-solid reaction apparatus over the range of 950-1250℃ were studied, and the thermodynamic and kinetic analyses were also performed. The results show that the average reaction rate of coke with H₂O is about 1.3-6.5 times that with CO₂ in the experimental temperature range. At the same temperature, the endothermic effect of coke with H₂O is less than that with CO₂. As the pressure increases, the gasification dissolution reaction of coke shifts to the high-temperature zone. The use of hydrogen-rich fuels is conducive to decreasing the energy consumed inside the blast furnace, and a corresponding high-pressure operation will help to suppress the gasification dissolution reaction of coke and reduce its deterioration. The interfacial chemical reaction is the main rate-limiting step over the experimental temperature range. The activation energies of the reaction of coke with CO₂ and H₂O are 169.23 kJ·mol-1 and 87.13 kJ·mol-1, respectively. Additionally, water vapor is more likely to diffuse into the coke interior at a lower temperature and thus aggravates the deterioration of coke in the middle upper part of blast furnace.     

Preparation and radar-absorbing properties of Al<Subscript>2</Subscript>O<Subscript>3</Subscript>/TiO<Subscript>2</Subscript>/Fe<Subscript>2</Subscript>O<Subscript>3</Subscript>/Yb<Subscript>2</Subscript>O<Subscript>3</Subscript> composite powder

Al₂O₃/TiO₂/Fe₂O₃/Yb₂O₃ composite powder was synthesized via the sol-gel method. The structure, morphology, and radar-absorption properties of the composite powder were characterized by transmission electron microscopy, X-ray diffraction analysis and RF impedance analysis. The results show that two types of particles exist in the composite powder. One is irregular flakes (100-200 nm) and the other is spherical Al₂O₃ particles (smaller than 80 nm). Electromagnetic wave attenuation is mostly achieved by dielectric loss. The maximum value of the dissipation factor reaches 0.76 (at 15.68 GHz) in the frequency range of 2-18 GHz. The electromagnetic absorption of waves covers 2-18 GHz with the matching thicknesses of 1.5-4.5 mm. The absorption peak shifts to the lower-frequency area with increasing matching thickness. The effective absorption band covers the frequency range of 2.16-9.76 GHz, and the maximum absorption peak reaches -20.18 dB with a matching thickness of 3.5 mm at a frequency of 3.52 GHz.     

Structural investigation and luminescent properties of BaZr(BO<Subscript>3</Subscript>)2:Eu<Superscript>3+</Superscript> phosphors containing Si

Si⁴⁺-doped BaZr(BO₃)₂:Eu³⁺ phosphors are prepared by a conventional solid-state reaction. The influence of Si⁴⁺ addition on the charge transfer state of Eu³⁺-O^2– and photoluminescence (PL) properties of BaZr(BO₃)₂:Eu³⁺ are discussed. Room temperature PL spectra indicated that efficient emission is obtained by Si doping. Increased values for the peak-peak ratio (PPR) of BaZr(BO₃)₂:Eu³⁺ at higher Si doping concentrations implied that the Eu³⁺ ion is located in a more asymmetric environment in BaZr_0.8Si_0.2(BO₃)₂:Eu³⁺ than in the undoped samples. The Judd-Ofelt parameters Ω_λ (λ=2,4) were calculated from the PL data, giving results that were consistent with those from the PPR. The maximum radiative quantum efficiency was achieved at a Si doping concentration of 20 mol%.     

Structure and magnetic properties of [FePt／Ag]10 multilayer films

[FePt/Ag]10 multilayers were deposited on glass substrates by magnetron sputtering. After being annealed at 550℃ for 30 rain, the coercivities of [FePt/Ag]10 multilayer films were observably improved. Magnetic properties of[FePt/Ag]10 multilayer films are influenced by the Ag content. The highest coercivity is obtained for those multilayer films that the Ag content is about 25%. The analysis for the remanence curves shows that the lower FePt layer thickness is favorable for decreasing the intergranular interaction. Result of XRD shows that a thick Ag layer can enhance the intensity of FePt(001) peak. A magnetic activation volume of the order of 10^-24 m^3 is obtained by the measurement of magnetic viscosity, showing that it is promising to be ultrahigh density recording media.     

ISEA reversed event in the Cretaceous Normal Super-chron （CNS）： ^40Ar／^39Ar dating and paleomagnetic results

ThegeomagneticfieldwasfoundtobeofnormalpolarityforalongtimeduringtheCretaceousbyHelsleyandSteiner[1]andthiswaslaternamedasCretaceousNormalSuperchron(CNS)[2].TheCNSlastedalmost37Ma(120—83Ma).Severalabnormalgeologicalevents,suchasanoceanicanoxicevent,alargenumberofvol-canismandglobalclimaticwarmingduringtheCNShavebeenreported[3—11].Thishasledtomanyquestionsbeingraised.IsittruethattheEarthsmagneticfielddidnotreverseatallintheCNS?Ifitdidreverse,howmanytimesandwhendidthishappen?Istherea…     

Different climatic controls of soil δ 13Corg in three mid-latitude regions of the Northern Hemisphere since the Last Glacial period

Paleoecological records of soil δ^13Corg from three regions in the middle latitudes of the Northern Hemisphere, including the Chinese Loess Plateau （CLP）, the Great Plains and adjacent areas of North America and northwestern Europe, showed different variations since the Last Glacial period. An attempt was made to evaluate the causes for the difference in δ^13Corg on the basis of the modern climatic data collected in these regions and of the modern C3 and C4 plant distributions. The analysis indicates that temperature, especially the growing season temperature, has a dominant control on the growth of C4 plants. When the mean annual or growing season temperatures are below the ＂threshold value＂, the growth of C4 plants is limited. When the temperature is above the ＂threshold value＂, C4 plants can grow under a wide range of precipitation. However, when the precipitation is high enough to favor the growth of trees, the proportions of C4 plants in local biomass will decline. The implicit control factor recovered by sedimentary records is consistent with the control factor on modern C3/C4 distribution. Pure C3 plants have been dominating the local biomass since the Last Glacial period in European loess region, mainly owing to the low local temperature. The increases in C4 plants from the late Pleistocene to the Holocene in the Chinese Loess Plateau, the Great Plains and adjacent areas, mainly reflect the influence of increasing temperature.