Hot deformation characteristics of as-cast high-Cr ultra-super-critical rotor steel with columnar grains

Isothermal hot compression tests of as-cast high-Cr ultra-super-critical (USC) rotor steel with columnar grains perpendicular to the compression direction were carried out in the temperature range from 950 to 1250°C at strain rates ranging from 0.001 to 1 s-1. The softening mechanism was dynamic recovery (DRV) at 950°C and the strain rate of 1 s-1, whereas it was dynamic recrystallization (DRX) under the other conditions. A modified constitutive equation based on the Arrhenius model with strain compensation reasonably predicted the flow stress under various deformation conditions, and the activation energy was calculated to be 643.92 kJ·mol-1. The critical stresses of dynamic recrystallization under different conditions were determined from the work-hardening rate (θ)–flow stress (σ) and -?θ/?σ–σ curves. The optimum processing parameters via analysis of the processing map and the softening mechanism were determined to be a deformation temperature range from 1100 to 1200°C and a strain-rate range from 0.001 to 0.08 s-1, with a power dissipation efficiency η greater than 31%.     

Hot deformation behavior of Super304H austenitic heat resistant steel

The hot compression tests of Super304H austenitic heat resistant steel were carried out at 800–1200℃ and 0.005–5 s-1 using a Gleeble 3500 thermal-mechanical simulator, and its deformation behavior was analyzed. The results show that the flow stress of Super304H steel decreases with the decrease of strain rate and the increase of deformation temperature; the hot deformation activation energy of the steel is 485 kJ/mol. The hot deformation equation and the relationship between the peak stress and the deformation temperature and strain rate is obtained. The softening caused by deformation heating cannot be neglected when both the deformation temperature and strain rate are higher.     

High-temperature mechanical properties and deformation behavior of high Nb containing TiAl alloys fabricated by spark plasma sintering

A high Nb containing TiAl alloy was prepared from the pre-alloyed powder of Ti-45Al-8.5Nb-0.2B-0.2W-0.02Y (at%) by spark plasma sintering (SPS). Its high-temperature mechanical properties and compressive deformation behavior were investigated in a temperature range of 700 to 1050℃ and a strain rate range of 0.002 to 0.2 s-1. The results show that the high-temperature mechanical properties of the high Nb containing TiAl alloy are sensitive to deformation temperature and strain rate, and the sensitivity to strain rate tends to rise with the deformation temperature increasing. The hot workability of the alloy is good at temperatures higher than 900℃, while fracture occurs at lower temperatures. The flow curves of the samples compressed at or above 900℃ exhibit obvious flow softening after the peak stress. Under the deformation condition of 900-1050℃ and 0.002-0.2 s-1, the interrelations of peak flow stress, strain rate, and deformation temperature follow the Arrhenius' equation modified by a hyperbolic sine function with a stress exponent of 5.99 and an apparent activation energy of 441.2 kJ·mol-1.     

高锰TRIP钢热变形行为研究

通过单轴压缩实验,研究了高锰TRIP钢(Fe15Mn3Si3Al)在800～1050℃温度范围内、应变速率ε.=0.01～5.0s-1条件下的热变形行为和组织变化,讨论了热变形参数对流变应力和显微组织的影响.结果表明:动态再结晶只在较高变形温度和低应变速率下发生.实验钢对温度和应变速率都很敏感,而应变速率对实验钢的热变形行为影响较大.高锰TRIP钢的表观应力指数n=3.909,变形激活能Q=353.167kJ/mol.根据实验数据,建立了高锰TRIP钢高温变形的热加工方程.     

Deformation behavior and microstructure of an Al-Zn-Mg-Cu-Zr alloy during hot deformation

The hot deformation behavior and microstructures of Al-7055 commercial alloy were investigated by axisymmetric hot compression at temperatures ranging from 300℃ to 450℃ and strain rates from 10-2 to 10 s-1, respectively. Microstructures of deformed 7055 alloy were investigated by transmission electron microscopy (TEM). The dependence of peak stress on deformation temperature and strain rate can be expressed by the hyperbolic-sine type equation. The hot deformation activation energy of the alloy is 146 kJ/mol. Moreover, the flow stress curves predicted by the modified constitutive equations are reasonably consistent with the experimental results, which confirms that the proposed deformation constitutive equations can provide evidence for the selection of hot forming parameters. TEM results indicate that dynamic recovery is the main softening mechanism during hot deformation.     

Hot deformation map and its application of GH4706 alloy

The hot deformation behaviors of GH4706 alloy were investigated using compression tests in a deformation temperature range from 900℃ to 1200℃ with a strain rate range of 0.001–1 s?1. Hot processing maps were developed on the basis of the dynamic material model and compression data. A three-dimensional distribution of power dissipation parameter (η) with strain rate and temperature reveals that η decreases in sensitivity with an increase in strain rate and a decrease in temperature. Microstructure studies show that the grain size of GH4706 alloy increases when η is larger than 0.32, and the microstructure exhibits local deformation when η is smaller than 0.23. The hot processing map at the strain of 0.7 exposes a domain peak at η=0.32 for the temperature between 940℃ and 970℃ with the strain rate from 0.015 s?1 to 0.003 s?1, and these are the optimum parameters for hot working.     

Dynamic recrystallization behavior of the Ti–48Al–2Cr–2Nb alloy during isothermal hot deformation

The hot deformation behavior of the as-cast Ti–48Al–2Cr–2Nb alloy was investigated by isothermal compression tests at deformation temperatures ranging from 1000℃ to 1200℃,and strain rates from 0.001 s~(-1)to 0.1 s~(-1).The single peak stress features common to all flow curves indicate that DRX is the dominating softening mechanism.The calculated values of the hot deformation activation energy Q and stress index n are 296.5 kJ mol~(-1)and 3.97,respectively.Based on this,the Arrhenius type constitutive equation was successfully established.The DRX critical condition model and relationship among DRX volume fractions,deformation temperatures and strain rates were obtained to optimize the process.Combined with microstructure analysis,it's concluded that 1200℃/0.01s~(-1)is the optimization parameter.Besides,both DDRX and CDRX were observed in theγphase evolution.The deformation mechanism from the inter-grain dislocation motion to the grain boundary migration and grain rotation was discussed.     

Constitutive behavior and processing maps of low-expansion GH909 superalloy

The hot deformation behavior of GH909 superalloy was studied systematically using isothermal hot compression tests in a temperature range of 960 to 1040℃ and at strain rates from 0.02 to 10 s-1 with a height reduction as large as 70%. The relations considering flow stress, temperature, and strain rate were evaluated via power-law, hyperbolic sine, and exponential constitutive equations under different strain conditions. An exponential equation was found to be the most appropriate for process modeling. The processing maps for the superalloy were constructed for strains of 0.2, 0.4, 0.6, and 0.8 on the basis of the dynamic material model, and a total processing map that includes all the investigated strains was proposed. Metallurgical instabilities in the instability domain mainly located at higher strain rates manifested as adiabatic shear bands and cracking. The stability domain occurred at 960-1040℃ and at strain rates less than 0.2 s-1; these conditions are recommended for optimum hot working of GH909 superalloy.     

Hot deformation behavior of uniform fine-grained GH4720Li alloy based on its processing map

The hot deformation behavior of uniform fine-grained GH4720Li alloy was studied in the temperature range from 1040 to 1130℃ and the strain-rate range from 0.005 to 0.5 s?1 using hot compression testing. Processing maps were constructed on the basis of compression data and a dynamic materials model. Considerable flow softening associated with superplasticity was observed at strain rates of 0.01 s?1 or lower. According to the processing map and observations of the microstructure, the uniform fine-grained microstructure remains intact at 1100℃ or lower because of easily activated dynamic recrystallization (DRX), whereas obvious grain growth is observed at 1130℃. Metallurgical instabilities in the form of non-uniform microstructures under higher and lower Zener–Hollomon parameters are induced by local plastic flow and primary γ′ local faster dissolution, respectively. The optimum processing conditions at all of the investigated strains are proposed as 1090–1130℃ with 0.08–0.5 s?1 and 0.005–0.008 s?1 and 1040–1085℃ with 0.005–0.06 s?1.     

S32750超级双相不锈钢的热变形及组织分析

利用MMS-200热模拟实验机,对S32750超级双相不锈钢在温度为1 000～1 150℃,应变速率为0.01～10 s-1的条件下进行了单道次压缩实验,测定了真应力-真应变曲线,对热变形组织进行了分析.实验结果表明:当变形温度一定时,峰值应力随着应变速率的增加而增加.提高热变形温度,降低应变速率,可以促进奥氏体动态再结晶的发生.根据热变形方程计算得到压缩变形时的热变形激活能Q=460 kJ/mol.在相应的变形条件下,获得了S32750超级双相不锈钢热变形过程中峰值应力与Z参数的关系式.     

铜/石墨复合材料热变形行为研究

通过Gleeble-3500热模拟试验机对铜/石墨复合材料进行热压缩试验,研究变形温度为700～850 ℃、应变速率为0.001～1.000 s^-1时该复合材料的热变行为。通过光学显微镜研究复合材料显微组织的演变,根据实验数据构建该复合材料的本构方程和热加工图。使用Zener-Hollomon参数模型对该复合材料的流变应力进行研究。研究发现,铜/石墨复合材料的流变应力随着应变温度的升高而降低,随应变速度的增大而增大。计算得出该复合材料的热变形激活能为463.02 kJ/mol,表明材料具有良好的成形能力。通过构建的本构方程验证了最大应力的吻合性,发现计算值和试验值的误差在9.5%以内,说明该方程对复合材料的流变行为具有指导作用。热加工图表明了该复合材料的适宜加工温度为780～820 ℃,变形速率为0.050～0.100 s^-1;变形温度为830～850 ℃时,变形速率约为0.001 s^-1。     

Hot deformation behaviors of WE71 alloy under plain strain compression at elevated temperature

Hot deformation behaviors of WE71 (Mg–7Y-1Nd-0.5Zr) alloy was investigated by plain strain compression tests conducted at temperatures ranging from 350 °C to 500 °C and strain rates varying from 0.01 s^-1 to 10 s^-1. Results show that the hot deformation of WE71 was accompanied by the precipitation of rich Zr phase with granular shape and block-shaped phase rich in element Y. When deformed at low temperature and high strain rate, the softening behavior of the alloy was synergically determined by shear bands propagation, adiabatic heating, twinning formation and dynamic recrystallization (DRX). For the conditions of high temperature and high strain rate, DRX was the major softening mechanism while the formation and annihilation of extension twinning resulted in a special flow curve characteristic at the strain of around 0.3. According to the microstructural observations, it can be concluded that the irregular flow curves of WE71 alloy during plain strain compression process are mainly ascribed to shear bands propagation, adiabatic heating, twinning formation and DRX.     

Microstructural evolution of a superaustenitic stainless steel during a two-step deformation process

Single- and two-step hot compression experiments were carried out on 16Cr25Ni6Mo superaustenitic stainless steel in the temperature range from 950 to 1150℃ and at a strain rate of 0.1 s-1. In the two-step tests, the first pass was interrupted at a strain of 0.2; after an interpass time of 5, 20, 40, 60, or 80 s, the test was resumed. The progress of dynamic recrystallization at the interruption strain was less than 10%. The static softening in the interpass period increased with increasing deformation temperature and increasing interpass time. The static recrystallization was found to be responsible for fast static softening in the temperature range from 950 to 1050℃. However, the gentle static softening at 1100 and 1150℃ was attributed to the combination of static and metadynamic recrystallizations. The correlation between calculated fractional softening and microstructural observations showed that approximately 30% of interpass softening could be attributed to the static recovery. The microstructural observations illustrated the formation of fine recrystallized grains at the grain boundaries at longer interpass time. The Avrami kinetics equation was used to establish a relationship between the fractional softening and the interpass period. The activation energy for static softening was determined as 276 kJ/mol.     

Effect of high temperature and high strain rate on the dynamic mechanical properties of Fe-30Mn-3Si-4Al TWIP steel

The dynamic mechanical properties of Fe-30Mn-3Si-4Al twinning induced plasticity (TWIP) steel were studied by the split-Hopkinson pressure bar (SHPB) at temperatures of 298–1073 K and strain rates of 700, 2500, and 5000 s?1. The TWIP steel indicates strain rate hardening effect between 700 and 2500 s?1, but it shows strain rate softening effect between 2500 and 5000 s?1. In addition, the strain rate softening effect enhances with an increase in deformation temperature. After deformation, the microstructures were studied by optical microscopy (OM). It is shown that the deformation bands become more convergence, a part of which become interwoven with an increase in strain rate, and the dynamic recovery and recrystallization are enhanced with an increase in both temperature and strain rate.     

Hot deformation behavior of microstructural constituents in a duplex stainless steel during high-temperature straining

The hot deformation characteristics of 1.4462 duplex stainless steel (DSS) were analyzed by considering strain partitioning between austenite and ferrite constituents. The individual behavior of ferrite and austenite in microstructure was studied in an iso-stress condition. Hot compression tests were performed at temperatures of 800–1100℃ and strain rates of 0.001–1 s?1. The flow stress was modeled by a hyperbolic sine constitutive equation, the corresponding constants and apparent activation energies were determined for the studied alloys. The constitutive equation and law of mixture were used to measure the contribution factor of each phase at any given strain. It is found that the contribution factor of ferrite exponentially declines as the Zener-Hollomon parameter (Z) increases. On the contrary, the austenite contribution polynomially increases with the increase of Z. At low Z values below 2.6.×1015 (lnZ=35.5), a negative contribution factor is determined for austenite that is attributed to dynamic recrystallization. At high Z values, the contribution factor of austenite is about two orders of magnitude greater than that of ferrite, and therefore, austenite can accommodate more strain. Microstructural characterization via electron back-scattered diffraction (EBSD) confirms the mechanical results and shows that austenite recrystallization is possible only at high temperature and low strain rate.     

Peculiarities of the rheological behavior and structure formation of aluminum under deformation at near-solidus temperatures

This paper deals with a peculiar rheological behavior of aluminum at near-solidus temperatures. It has been experimentally established that there is an inverse strain rate dependence of strain resistance at temperatures ranging between 560 and 640°С and strain rates ranging from 0.06 to 1.2 s-1. Electron backscatter diffraction analysis has shown that at temperatures ranging between 540 and 640°С and strain rates ranging from 0.06 to 0.1 s-1, the main process of softening is dynamic polygonization, resulting in in situ recrystallization. At higher strain rates, ranging between 0.8 and 1.2 s-1, and temperatures ranging between 560 and 640°С, the recovery is dynamic. This unusual behavior of the mechanism of softening and the presence of the inverse strain rate dependence of strain resistance can be explained by blocking the motion of free dislocations by foreign atoms, which occurs at strain rates ranging between 0.06 and 0.1 s-1. This process results in dislocation pile-up, thereby causing in situ recrystallization. At strain rates exceeding 0.16 s-1, there is no intensive blocking of dislocations, leading to a direct strain rate dependence of strain resistance.     

800H合金热变形行为研究

通过高温单道次压缩实验,研究800H合金在变形温度850～1 050℃和应变速率0.01～10 s-1条件下的热变形行为和微观组织变化.根据单道次压缩实验数据,绘制了不同变形条件下的800H合金真应力-真应变曲线,通过非线性回归建立了流变应力数学模型;通过线性回归建立了不同温度区间内热变形本构方程.分析了热变形条件对合金微观组织的影响,结果表明:动态再结晶更有可能发生在低应变速率和高变形温度的变形条件下;当变形温度低于950℃时,沿晶界析出的Cr23C6粒子对动态再结晶的发生有一定的抑制作用.     

Hot deformation behavior andfl ow stress modeling of annealed AZ61 Mg alloys

In this study, the hyperbolic-sine type constitutive equation was used to model the flow stress of annealed AZ61 magnesium(Mg) alloys. Hot compression tests were conducted at the temperatures ranging from 250 1C to 450 1C and at the strain rates ranging from 1 10–3s 1to 1 s 1on a Gleeble-3500 thermo-simulation machine. Constitutive equations as a function of strain were established through a simple extension of the hyperbolic sine constitutive relation. The effects of annealing heat treatments on the variations in constitutive parameters with strain were discussed. The hot compressive flow curves exhibited typical features of dynamic recrystallization. Multiple peak flow curves were observed in the annealed specimens upon testing at a strain rate of 1 10 1s–1and at various temperatures. Variations in constitutive parameters with strain were related to flow behavior and dependent on the initial conditions of the test specimens. The flow stresses of annealed AZ61 Mg alloys were predicted well by the strain-dependent constitutive equations of the hyperbolic sine function under the deformation conditions employed in this study.     

Kinetic analysis and strain-compensated constitutive models of Ti-42.9Al-4.6Nb–2Cr during isothermal compression

The hot deformation behavior of Ti-42.9Al-4.6Nb–2Cr (at. %) was investigated by isothermal compression tests at the deformation temperature range of 1373–1573 K, strain rate range of 0.001–1.0 s⁻¹, up to the strain of 0.69. The flow stress test results of Ti-42.9Al-4.6Nb–2Cr showed negative temperature and positive strain rate sensitivity. Besides, strain had a great effect on the hot deformation behavior of Ti-42.9Al-4.6Nb–2Cr. Kinetic analysis was adopted to assess the hot workability of Ti-42.9Al-4.6Nb–2Cr via apparent activation energy (Q) of hot deformation, strain-rate sensitivity index (m) and strain hardening index (n). The Q value varied from 607.1 ± 0.7 kJ·mol⁻¹ to 512.6 ± 10.8 kJ mol⁻¹ with the increasing of strain from 0.1 to 0.6. The effect of strain on the Q value at the deformation temperatures below 1473 K was mainly related to dynamic recrystallization of γ phase and kinking of γ lamellae, while the Q value at the deformation temperature above 1473 K might be linked to γ→α phase transformation and DRV of α phase. Based on the kinetic analysis, strain-compensated Arrhenius model and Hensel-Spittel model were successfully established to predict the hot workability (flow stress). Average absolute relative errors of established strain-compensated Arrhenius model and Hensel-Spittel model were 7.52% and 11.95%, respectively. Moreover, both established constitutive models can be extrapolated for predicting the flow stress of Ti-42.9Al-4.6Nb–2Cr to larger strain levels.     

20Mn2SiV非调质钢热变形流变应力模型

利用MMS-300热模拟试验机,对20Mn2SiV非调质钢在变形温度为900~1 100℃及应变速率为0.01~10s-1条件下的流变应力进行了研究,讨论了Z参数与动态再结晶之间的关系,并建立了该钢的热变形流变应力模型.结果表明:采用Z参数可以判断动态再结晶发生与否,当lnZ≤32.76时,20Mn2SiV非调质钢发生动态再结晶;根据动态再结晶发生与否以及应变是否达到动态再结晶临界应变值,分别建立了不同情况下的流变应力模型,模型拟合效果良好.