Q&P1180高强钢激光焊接头的抗氢脆性能研究

采用激光焊技术对汽车用Q&P1180高强钢进行焊接试验,分析焊接工艺参数对激光焊接头组织演变和性能的影响。选择综合力学性能较好的试样进行低应变速率拉伸试验,研究激光焊接头不同区域的微观组织对Q&P1180高强钢氢脆敏感性的影响。结果表明,当激光功率为2.5～3.5 kW、焊接速度为4.0 m/min(或激光功率为3.0 kW,焊接速度为3.6～4.2 m/min)时,Q&P1180高强钢激光焊获得了全焊透及表面成形良好的接头。不同激光功率和不同焊接速度下,焊缝区和热影响区的硬度均高于母材区的,且在焊缝的两边都存在一个软化区。在激光功率为3.0 kW、焊接速度为4.0 m/min时,激光焊接头的综合性能最佳。在预充氢的慢应变速率拉伸试验中,随着充氢电流密度的增大或充氢时间的延长,其抗拉强度和塑性逐渐下降。其中,当充氢电流密度为2 mA/cm²、充氢时间为5 min时,氢脆敏感性因子为78.0%,具有较高的氢脆敏感性。     

Electromigration in eutectic SnAg solder reaction couples with various ambient temperatures and current densities

The electromigration behavior of eutectic SnAg solder reaction couples was studied at various temperature (25 and 120℃ when the current density was held constant at 104 A/cm2 or 5×103 A/cm2. Under the current density of 104 A/cm2, scallop type Cu₆Sn₅ spalls and migrates towards the direction of electron flow at room ambient temperature (25℃), but transforms to layer type Cu₃Sn and leaves Kirkendall voids in it at high ambient temperature (120℃). Under the current density of 5×103 A/cm2 plus room ambient temperature, no obvious directional migration of metal atoms/ions is found. Instead, the thermal stress induced by mismatch of dissimilar materials causes the formation of superficial valley at both interfaces. However, when the ambient temperature increases to 120℃, the mobility of metal atoms/ions is enhanced, and then the grains rotate due to the anisotropic property of β-Sn.     

电力输电杆塔用Q235钢聚硅氧烷复合涂层的大气腐蚀行为

采用喷涂法在Q235钢表面涂覆聚硅氧烷复合涂层,在重工业污染区、人口密集区、一般工业区、乡村定居区4个220kV变电站大气环境中自然暴露15个月,采用伏安法、交流阻抗法等研究其腐蚀行为。结果表明,重工业污染区变电站的腐蚀电流密度从3.849 5×10~(-12) A/cm~2增加到15个月的2.257 2×10~(-10) A/cm~2;而人口密集区变电站的腐蚀电流密度值先从1.640 1×10~(-10) A/cm~2降低到6个月的5.736 5×10~(-11) A/cm~2,后增加到15个月的3.929 9×10~(-10) A/cm~2。结合自腐蚀电位和涂层阻抗,聚硅氧烷复合涂层在不同环境中耐蚀性顺序为:人口密集区乡村定居区一般工业区重工业污染区。     

Red organic light emitting device with improved performance using a novel fluorescent dye codoped with phosphor-sensitizer

Efficient red organic light-emitting device consisted of a compound fluorescent-phosphor-sensitized emission layer was fabricated. A novel red fluorescent dye, 3-(dicyanomethylene)-5,5-dimethyl-1-(4-dimethylamino-styryl) cyclohexene (DCDDC), and a green phosphorescent dye, fac tris(2-phenylpyridine) iridium [Ir(ppy)3] were codoped into a host material 4,4’-N,N’-dicarbazolebiphenyl (CBP). By adjusting the component ratio of doping system, a series of devices with different concentration proportion of Ir(ppy)3:DCDDC were constructed. The results demonstrated that the device with 0.2 wt% DCDDC had a maximum power efficiency (η_p) of 2.12 lm/W at a current density of 0.1 mA/cm², which was about 38% higher than that of conventional fluorescent device. When at a current density of 4 mA/cm2 (100 cd/m²) and 52 mA/cm² (1000 cd/m²), the η_p percentage was about 160% and 143% higher than that of conventional device, respectively. A stable red light emission at a peak of 615 nm with Commissions Internationale de l’Eclairage coordinates near the region of (0.56, 0.42) in a wide bias range was also obtained. The improved performances were attributed to the efficient multiple-stage energy transfer from the host to the guest and the suppression of loss mechanism.     

High critical current density in powder-in-tube processed MgB2/Ta/Cu wire

The magnetization of dense MgB₂/Ta/Cu wires prepared by the powder-in-tube method is measured by a SQUID magnetometer. The results indicate that the critical temperature of MgB₂/Ta/Cu is around 38.4 K with a sharp transition width of 0.6 K. The MgB₂/Ta/Cu wire shows a strong flux pinning and the critical current density is higher than 10⁵ A/cm² (5 K, self-field) and 10⁴ A/cm² (20 K, 1 T). Also, the irreversibility field of the sample reaches 6.6 T at 5 K.     

二维NiFe-LDH/Mo(OS)x纳米片协同促进电催化析氧反应

过渡族金属基二维纳米材料作为电催化析氧反应（oxygen evolution reaction, OER）催化剂具有巨大的潜力。通过原位电沉积法,在泡沫镍基底表面制备了二维层状镍铁双氢氧化物（NiFe-LDH）和氧硫化钼Mo(OS)_x纳米片异质结构。NiFe LDH/Mo(OS)_x电极在1 M KOH溶液中表现出优异的OER性能和长效稳定性,在10 mA/cm²电流密度下过电势仅为220 mV。在100、500 mA/cm²的高电流密度下,也能达到253、304 mV的低过电势。研究结果表明,NiFe-LDH/Mo(OS)_x电极优异的OER性能归因于Mo(OS)_x和NiFe LDH的协同作用,极大地促进了Fe²⁺向Fe³⁺活性物质的转化,并促进了氧空位的形成。这种协同制备方法为合理构建和设计异质结构电催化剂,实现高效的水分解提供了帮助。     

中温SOFC阴极材料La0.7Sr0.3Co1-xCuxO3-δ的制备及性能

采用固相反应法制备了La_0.7Sr_0.3Co_1-xCu_xO_3-δ系列中温固体氧化物燃料电池（SOFC）阴极材料粉体.对其进行晶体结构表征,高温电导率和热膨胀曲线测试,并选取其中性能较好的样品进行了单电池实验.结果表明,Cu的掺杂降低了（La,Sr）CoO La₃体系阴极材料的热膨胀系数,在x=0.05时电导率略高于未掺Cu的样品.以La_0.7Sr_0.3Co_0.95Cu _0.05O _3-δ为阴极、Ce_0.8Sm_0.2O_1.9为电解质组成的SOFC单电池,在850℃最大短路电流密度达511mA/cm²,最大输出功率密度约为0.106W/cm².     

Carrier transport characteristics of H-terminated diamond films prepared using molecular hydrogen and atomic hydrogen

The H-terminated diamond films, which exhibit high surface conductivity, have been used in high-frequency and high-power electronic devices. In this paper, the surface conductive channel on specimens from the same diamond film was obtained by hydrogen plasma treatment and by heating under a hydrogen atmosphere, respectively, and the surface carrier transport characteristics of both samples were compared and evaluated. The results show that the carrier mobility and carrier density of the sample treated by hydrogen plasma are 15 cm2·V-1·s-1 and greater than 5×1012 cm-2, respectively, and that the carrier mobilities measured at five different areas are similar. Compared to the hydrogen-plasma-treated specimen, the thermally hydrogenated specimen exhibits a lower surface conductivity, a carrier density one order of magnitude lower, and a carrier mobility that varies from 2 to 33 cm2·V-1·s-1. The activated hydrogen atoms restructure the diamond surface, remove the scratches, and passivate the surface states via the etching effect during the hydrogen plasma treatment process, which maintains a higher carrier density and a more stable carrier mobility.     

Simple method to rapidly fabricate chain-like carbon nanotube films and its field emission properties

A simple process to fabricate chain-like carbon nanotube (CNT) films by microwave plasma-enhanced chemical vapor deposition (MPCVD) was developed successfully. Prior to deposition, the Ti/Al₂O₃ substrates were ground with Fe-doped SiO₂ powder. The nano-structure of the deposited films was analyzed by scanning electron microscopy (SEM), transmission electron microscopy (TEM), and Raman spectroscopy. The field electron emission characteristics of the chain-like carbon nanotube films were measured under the vacuum of 10-5 Pa. The low turn-on field of 0.80 V/μm and the emission current density of 8.5 mA/cm2 at the electric field of 3.0 V/μm are obtained. Based on the above results, chain-like carbon nanotube films probably have important applications in cold cathode materials and electrode materials.     

Ohmic contact properties of p-type surface conductive layer on H-terminated diamond films prepared by DC arc jet CVD

With the advantages of high deposition rate and large deposition area, polycrystalline diamond films prepared by direct current (DC) arc jet chemical vapor deposition (CVD) are considered to be one of the most promising materials for high-frequency and high-power electronic devices. In this paper, high-quality self-standing polycrystalline diamond films with the diameter of 100 mm were prepared by DC arc jet CVD, and then, the p-type surface conductive layer with the sheet carrier density of 1011-1013 cm?2 on the H-terminated diamond film was obtained by micro-wave hydrogen plasma treatment for 40 min. Ti/Au and Au films were deposited on the H-terminated diamond surface as the ohmic contact electrode, respectively, afterwards, they were treated by rapid vacuum annealing at different temperatures. The properties of these two types of ohmic contacts were investigated by measuring the specific contact resistance using the transmission line method (TLM). Due to the formation of Ti-related carbide at high temperature, the specific contact resistance of Ti/Au contact gradually decreases to 9.95 × 10?5 Ω·cm2 as the temperature increases to 820℃. However, when the annealing temperature reaches 850℃, the ohmic contact for Ti/Au is degraded significantly due to the strong diffusion and reaction between Ti and Au. As for the as-deposited Au contact, it shows an ohmic contact. After annealing treatment at 550℃, low specific contact resistance was detected for Au contact, which is derived from the enhancement of interdiffusion between Au and diamond films.     

两步法制备性能优良的ZnO纳米线

利用热蒸发和溶液浸泡两步法制备了性能优良的ZnO纳米线,研究了这些ZnO纳米线的光致发光和场发射特性.与直接采用热蒸发方法生长的ZnO纳米线相比,由该方法得到的ZnO纳米线表现出了更好的紫外发光特性,同时发生5 nm的蓝移,场发射测试表明其开启电场和阈值电场分别达到2.3 V/μm和6.8 V/μm.该方法适用于制备光致发光和场发射性能优良的ZnO纳米线.     

NbC纳米析出相对低合金高强钢氢致开裂的影响研究

We investigated the effect of nanosized NbC precipitates on hydrogen-induced cracking (HIC) of high-strength low-alloy steel by conducting slow-strain-rate tensile tests (SSRT) and performing continuous hydrogen charging and fracture analysis. The results reveal that the HIC resistance of Nb-bearing steel is obviously superior to that of Nb-free steel, with the fractured Nb-bearing steel in the SSRT exhibiting a smaller ratio of elongation reduction (I_δ). However, as the hydrogen traps induced by NbC precipitates approach hydrogen saturation, the effect of the precipitates on the HIC resistance attenuate. We speculate that the highly dispersed nanosized NbC precipitates act as irreversible hydrogen traps that hinder the accumulation of hydrogen at potential crack nucleation sites. In addition, much like Nb-free steel, the Nb-bearing steel exhibits both H-solution strengthening and the resistance to HIC.     

泡沫镍上原位生长CoMn2O4多级空心纳米球作为超级电容器电极材料的电化学性能研究

采用水热法结合空气气氛中的热处理过程,在泡沫镍（NF）表面生长了锰酸钴（CoMn₂O₄）多级空心纳米球,通过X射线衍射仪（XRD）、场发射扫描电镜（FE-SEM）和X射线光电子能谱（XPS）等测试手段对纳米球进行了表征.在三电极电化学测量系统中,0.1Co²⁺-250电极材料在5 mA·cm^-2时的面积比电容高达6 184 mF·cm^-2.以0.1Co²⁺-250为正极,商用活性炭（AC）为负极组装而成的混合超级电容器,在1.6 mW·cm^-2时的最大能量密度为0.112 mWh·cm^-2.即使在功率密度为16 mW·cm^-2时,能量密度仍达到0.064 mWh·cm^-2.在2 mA·cm^-2的电流密度下,经过10 000次充放电循环后,电容保持了初始值的93%.因其优越的电化学性能和低成本的便捷合成方法,CoMn₂O₄多级空心纳米球作为电极材料具有重要的应用前景.     

Influences of fluorine auxochrome in fluorene molecular electroluminescent material on optoelectronic property

The UV-Vis absorption and photoluminescence （PL） spectra of 2,3-bis（9,9-dihexyl-9H-fluoren-2-yl） quinoxaline （Py）, 2,3-bis（9,9-dihexyl-9H-fluoren-2-yl）-6,7-difluoroquinoxaline （F2Py） and 2,3-bis（9,9- dihexyl-9H-fluoren-2-yl）-5,6,7,8-tetrafluoroquinoxaline （F4Py）, which are fluorene molecular derivatives with conjugated structure, were investigated. For further investigation of the influences of fluorine suxochrome in fluorene molecular electroluminescent material on optoelectronic property, the electroluminescence （EL） characteristics of materials were studied by double-layer organic light-emitting diodes （OLEDs） using N,N＇-Di-[（1-naphthalenyl）-N,N＇-diphenyl]-（1,1＇-biphenyl）-4,4＇-diamine （NPB） as a hole transporting layer （HTL） with the conventional vacuum deposition method. The results showed that the absorption and PL spectra of materials in film state red shifted with fluorine substituenta increased in molecule configuration. The performance of OLEDs is as follows： at a bias voltage of 5 V, Py emitted a blue-green light at 508 nm with the Commission Internationale d＇Eclairage （ClE） coordinates of （0.23, 0.43） and full width at half maximum （FWHM） of 100 nm. The device had a turn-on voltage （defined as the drive voltage at the luminance of 1 cd/m^2） of 4.8 V, a luminance of 129 cd/m^2 with a current density of 59 mA/cm^2 at 10 V, and a maximum luminous efficiency of 0.18 lm/W at 5.4 V. F2Py and F4Py emitted a green light peaking at 544 nm and a yellow light at 570 nm at 5 V, with the CIE coordinates of （0.38, 0.56） and （0.44, 0.49）, and FWHM of 103 and 117 nm, respectively. The F2Py and F4Py devices had a turn-on voltage of 4 and 2 V, a luminance of 557 and 3300 cd/m^2 with a current density of 100 and 880 mA/cm^2 at 10 V, and a maximum luminous efficiency of 0.22 lm/W at 7.6 V and 0.53 lm/W at 2 V, respectively.     

Luminescent and photovoltaic properties of poly（9,9-dioctylfluorene- co-bithiophene） in organic electronic devices

We studied the luminescent and photovoltaic properties of poly(9,9-dioctylfluorene-co-bithiophene)(F8T2) based on ITO/PEDOT:PSS/F8T2/Bphen/LiF(0 or 1 nm)/Al and ITO/PEDOT:PSS/F8T2:PCBM/Bphen/Al.A stable and bright yellow emission was obtained from polymer F8T2,and the electroluminescence power reached 45 ?W at a 15 V driving voltage.Polymer F8T2 shows a broad absorption band from 400 to 500 nm,and has a shorter absorption edge at about 560 nm compared to that of the typical electron donor P3HT(650 nm).The photoluminescence quenching of F8T2 occurs with only a small fraction of blended PCBM due to the effective exciton dissociation at the interface between F8T2 and PCBM.Polymer solar cells(PSCs) using F8T2:PCBM as the active layer show a low power conversion efficiency(PCE) of 0.10% with an open circuit voltage(Voc) of 0.91 V and short circuit current density(Jsc) of 0.23 mA/cm2.The PSCs using F8T2:P3HT:PCBM as the active layer have a Voc of 0.85 V and Jsc of 3.02 mA/cm2,improving the PCE by about 0.90%.We attribute the improved cell performance to the higher number of photons harvested by P3HT molecules.     

Preparation of mesoporous MgO-templated carbons from phenolic resin and their applications for electric double-layer capacitors

Mesoporous carbons were synthesized using thermoplastic phenolic resin (PF) as carbonaceous precursor and magnesium citrate as template precursor. Pore structure was determined as ink-bottle-like geometry through TEM, N2 adsorption analysis combined with TG curves. The porous carbons prepared were then applied as electrode material for electric double-layer capacitors. The capacitor performance was examined in 30 wt% KOH aqueous solution by cyclic voltammetry and galvanostatic charge/discharge measurements. The carbon prepared with MgO/PF mass ratio of 8/2 had a BET surface area of 1920 m² g^?1 and exhibited a capacitance of 220 F g^?1 at a current density of 50 mA g^?1. Besides, the carbon with the ratio of 4/6 had the optimize proportion of mesopores, which ensures its good rate performance that up to 98.3%, expressed as the ratio of the capacitance measured at 1000 mA g^?1 against that at 50 mA g^?1.     

钒电池充放电测试系统及测试方法研究

为了检测钒电池的充放电性能,根据全钒液流电池的特点,标称出钒电池的额定参数。在不同电流密度下对单体钒电池进行充放电容量测试实验。比较了不同电流密度下的充电曲线,从理论上分析充电差异的原因,总结充电电流与钒电池容量的关系。实验表明,对钒电池进行充放电时采用的电流密度为60~80 m A/cm2之间的值,钒电池电学性能参数最佳。     

Near infrared polymer light-emitting diodes

High efficiency of near infrared polymer light-emitting diodes with bilayer structure was obtained. The diode structure is ITO/PEDOT/LI/L2/Ba/Al, where L1 is phenyl-substituted poly [p-phenylphenylene vinylene] derivative (P-PPV), L2 is 9,9-dioctylfluorene (DOF) and 4,7-bis(3-hexylthiophen)-2-yl-2,1,3-naphthothiadiazole (HDNT) copolymer (PFHDNTI0). The electroluminescence (EL) spectrum of diodes from PFHDNTI0 is at 750 nm located inthe range of near infrared. The maximum external quantum efficiency is up to 2.1% at the current density of 35 mA/m^2. The improvement of the diode‘s performances was considered to be the irradiative excitons confined in the interface between L1 and L2 layers.     

Field Emission Characterization of 1D-Nanostructural ZnO Grown at Low Temperature

Ondeu-ctdio rmse nhsaivoen aaltt rwaicdteed b aan gdr-egaatp d neaaln oosft uartctteunrtialon se bmeiccaounse-of their remarkable physical and chemical properties[1 ,2].Amongthose properties ,the highaspect ratio of these materi-als makes them genuine can…     

Effect of shot peening on hydrogen embrittlement of high strength steel

The effect of shot peening (SP) on hydrogen embrittlement of high strength steel was investigated by electrochemical hydrogen charging, slow strain rate tensile tests, and hydrogen permeation tests. Microstructure observation, microhardness, and X-ray diffraction residual stress studies were also conducted on the steel. The results show that the shot peening specimens exhibit a higher resistance to hydrogen embrittlement in comparison with the no shot peening (NSP) specimens under the same hydrogen-charging current density. In addition, SP treatment sharply decreases the apparent hydrogen diffusivity and increases the subsurface hydrogen concentration. These findings are attributed to the changes in microstructure and compressive residual stress in the surface layer by SP. Scanning electron microscope fractographs reveal that the fracture surface of the NSP specimen exhibits the intergranular and quasi-cleavage mixed fracture modes, whereas the SP specimen shows only the quasi-cleavage fractures under the same hydrogen charging conditions, implying that the SP treatment delays the onset of intergranular fracture.