| 微型直齿沟槽铜管充液旋压-多级拉拔复合成形 |
| |
| 引用本文： | 欧栋生,汤勇,万珍平,陆龙生,练彬.微型直齿沟槽铜管充液旋压-多级拉拔复合成形[J].华南理工大学学报(自然科学版),2010,38(12). |
| |
| 作者姓名： | 欧栋生 汤勇 万珍平 陆龙生 练彬 |
| |
| 作者单位： | 华南理工大学机械与汽车工程学院; |
| |
| 基金项目： | 国家自然科学基金-广东省联合基金重点资助项目，华南理工大学自然科学青年基金资助项目 |
| |
| 摘 要： | 采用高速充液旋压-多级拉拔复合成形方法加工出了直径在6mm以下的、质量稳定的微型直齿沟槽铜管.在分析其加工成形机理的基础上,研究了加工参数对沟槽铜管质量的影响.结果表明:微型直齿沟槽铜管成形过程中,过大的拉拔级次压缩率会导致微型直齿沟槽铜管的轴向沟槽产生断裂或折叠,过大的圆度误差会导致微型直齿沟槽铜管表面产生皱折和凹陷;而拉拔模具入口锥角采用16°、定径区长度取4mm、出口锥角取30°、润滑条件良好及残余应力较小时,拉拔沟槽铜管表面质量更高.通过控制拉拔工艺参数和圆度误差,可获得直径在6mm以下的、质量稳定的微型直齿沟槽铜管,且内部沟槽趋于封闭,呈燕尾槽特征,有利于提高微型直齿沟槽铜管的毛细力.
|
| 关 键 词： | 微沟槽 充液旋压 多级拉拔 拉拔参数 热管 |
Composite Machining of Copper Tube with Micro Straight Grooves via Oil-Filled Spinning and Multi-Pass Drawing |
| |
| Ou Dong-sheng,Tang Yong,Wan Zhen-ping,Lu Long-sheng,Lian Bin.Composite Machining of Copper Tube with Micro Straight Grooves via Oil-Filled Spinning and Multi-Pass Drawing[J].Journal of South China University of Technology(Natural Science Edition),2010,38(12). |
| |
| Authors: | Ou Dong-sheng Tang Yong Wan Zhen-ping Lu Long-sheng Lian Bin |
| |
| Institution: | Ou Dong-sheng Tang Yong Wan Zhen-ping Lu Long-sheng Lian Bin(School of Mechanical and Automotive Engineering,South China University of Technology,Guangzhou 510640,Guangdong,China) |
| |
| Abstract: | High-quality copper tube with micro straight grooves,which is less than 6mm in outer diameter,was fabricated via the composite process of high-speed oil-filled spinning and multi-pass drawing.Then,the corresponding machining mechanism was analyzed,and the influences of machining parameters on the quality of the product were investigated.The results indicate that,during the machining,excessive drawing reduction may result in groove folding and crack,and excessive roundness error may lead to crinkle even depr... |
| |
| Keywords: | micro groove oil-filled spinning multi-pass drawing drawing parameter heat pipe |
| 本文献已被 CNKI 万方数据 等数据库收录！ |
|
