| 工艺参数对铝合金微齿轮热挤压成形的影响 |
| |
| 引用本文： | 陈泽中,程志龙,李雪源,赵娜.工艺参数对铝合金微齿轮热挤压成形的影响[J].上海理工大学学报,2018,39(2):12-17. |
| |
| 作者姓名： | 陈泽中 程志龙 李雪源 赵娜 |
| |
| 作者单位： | 上海理工大学 材料科学与工程学院, 上海 200093,上海理工大学 材料科学与工程学院, 上海 200093,上海理工大学 材料科学与工程学院, 上海 200093,上海理工大学 材料科学与工程学院, 上海 200093 |
| |
| 摘 要： | 针对7075铝合金微齿轮挤压过程中出现的微尺度效应问题，将退火后的7075铝合金进行等温微压缩试验，获得材料的真实应力应变曲线，导入DEFORM软件，并模拟微挤压成形过程。定义挤出端凸度来评定微挤压件的成形性能，挤出端凸度越小，则成形性越好。设计正交试验，研究入模角、坯料直径、挤压温度、挤压速度和摩擦因数等对微齿轮热挤压成形过程中最大成形载荷和成形性能的影响规律。分析结果表明：坯料直径对最大成形载荷和挤出端凸度的影响均最大；挤压速度对成形载荷的影响较大，挤压温度的影响次之；挤压温度对挤出端凸度的影响较大，挤压速度的影响次之；入模角和摩擦因数对成形载荷和挤出端凸度影响均较小。通过优化工艺参数模拟挤压得到质量良好的微齿轮。
|
| 关 键 词： | 微齿轮 热挤压 数值模拟 成形载荷 挤出端凸度 |
| 收稿时间： | 2017/9/14 0:00:00 |
Effect of Process Parameters on Hot Extrusion Forming of Aluminum Alloy Micro-gear |
| |
| CHEN Zezhong,CHENG Zhilong,LI Xueyuan and ZHAO Na.Effect of Process Parameters on Hot Extrusion Forming of Aluminum Alloy Micro-gear[J].Journal of University of Shanghai For Science and Technology,2018,39(2):12-17. |
| |
| Authors: | CHEN Zezhong CHENG Zhilong LI Xueyuan and ZHAO Na |
| |
| Institution: | School of Materials Science and Engineering, University of Shanghai for Science and Technology, Shanghai 200093, China,School of Materials Science and Engineering, University of Shanghai for Science and Technology, Shanghai 200093, China,School of Materials Science and Engineering, University of Shanghai for Science and Technology, Shanghai 200093, China and School of Materials Science and Engineering, University of Shanghai for Science and Technology, Shanghai 200093, China |
| |
| Abstract: | Aiming at microscale effect in micro-extrusion process for 7075 aluminum alloy gear,the true stress-strain curve of 7075 aluminum alloy were obtained by isothermal and micro compression experiment.Numerical simulation for forming process of micro-gear extrusion was studied by using DEFORM software with the true stress-strain data.The standard of convexity of extruding parts is initialized to evaluate the formability of micro-extrusion parts.The effect of die angle,blank diameter,extrusion temperature,extrusion velocity and friction coefficient on the maximum forming load and convexity of extruding was investigated by using orthogonal array method.The results showed that the blank diameter had the greatest influence on both the maximum forming load and convexity of extruding parts.And die angle and friction coefficient had little influence on the experiment indicators.The extrusion velocity had greater influence on forming load while that of the extrusion temperature is inferior.The extrusion temperature had greater influence on convexity of extruding while that of extrusion velocity is inferior.The micro-gear with good dimensional accuracy and surface quality was obtained by optimizing the process parameters. |
| |
| Keywords: | micro-gear hot extrusion numerical simulation forming load convexity of extruding |
|
| 点击此处可从《上海理工大学学报》浏览原始摘要信息 |
| 点击此处可从《上海理工大学学报》下载免费的PDF全文 |
|
