堆焊切粒刀技术初探

介绍堆焊切粒刀的优点 ,着重探讨了采用靠模法加工堆焊切粒刀螺旋槽的原理 ,论证了所介绍加工工艺的合理性 .事实证明 ,采用介绍的加工工艺生产的堆焊切粒刀 ,可满足设计的技术性能 ,质量可达到国外同类产品的水平     

Experimental Study on the Milling of a Ti Beta 21S

Ti Beta 21S (Ti-15Mo-2.7Nb-3Al-0.2Si) was devel op ed by TIMET in 1989. It is a metastable beta titanium alloy that offers subs tantial weight reductions over other engineering materials. Compared with common beta Ti alloys, it offers the high specific strength, good cold formability, im proved oxidation resistance, elevated temperature strength, creep resistance, an d thermal stability. Besides the common characters of titanium alloy, such as po or heat diffusivity, low elastic modulus, Ti Beta 21S has ...     

The Extraction Method of Cutting Engagement in Ball-end Milling Simulation

Ball-end mill is widely used in workpiece processi ng with free-form surfaces. Such models that can predict processing character istics precisely are very necessary to the aim of cost reducing, quality improvi ng and productivity progressing, the cutting force prediction is the most import ant among these models. To explore the physical essence of metal cutting, model researchers commonly simplify the geometric conditions in cutting process, and a ssume that the geometric parameters that are needed to s...     

BM-20Д2型排粉机轴封漏粉改造

阐述了漳泽发电厂二期BM-20Д2型排粉机轴封漏粉原因、轴封结构及改造方法。     

步进电机细分技术在经济型数控机床中的应用

本文叙述了步进电机细分原理及微机控制系统，并将其应用于经济型数控铣床的横向进给伺服系统，有效提高了开环数控系统的定位精度。     

Study on End Milling Generation Surface Model and Simulation in View of Main Axle s Tolerance

In accordance with the relative movement between end-milling cutter and workpiece surface, a theoretical generation model for milled surface was established with the movement error of principal axle considered. Then the milled surfaces under various cutting condition were simulated, the results of which showed that end milled surfaces were of “vaulted profile“, heights of surface irregularty at various points to be different with maximum value in the middle and smaller at both sides, the difference were ...     

WO3粉在高速层间剪切条件下的颗粒破碎特征

研究了WO3粉和W粉的剪切破碎时间对WO3粉和W粉的沉降曲线、平均粒度、BET比表面及松装密度的影响.用TEM和SEM对剪切破碎前后的粉末进行了直接观察.结果表明:新型剪切破碎机能有效地粉碎微米级WO3等脆性粉末,同时可以破坏超细W粉中的桥接团粒,使W粉和WO3粉的松装密度增加1倍以上,但对比表面积影响不大.     

PCBN铣刀硬加工时切削用量的选择

通过试验分析研究,介绍了PCBN铣刀硬加工Cr12MoV等淬火钢材料时切削用量对刀具寿命的影响,给出了PCBN刀具铣削淬火钢时切削用量及刀具磨钝标准的选用原则和范围.     

Mg-Ni合金在球磨过程中温度变化的理论及实验研究

通过计算磨球运动的最大速度估算了Mg-Ni粉末在球磨过程中可能达到的最高温度,并采用X-射线衍射仪(XRD)、扫描电子显微镜(SEM)、能谱分析仪研究了样品经400 r/min球磨不同时间后的相结构、形貌及微区成分的变化规律.结果表明:当球磨速度为400r/min时,可使落入两个直径为20mm的碰撞磨球之间、质量为0.033 3 g的粉末温度从298 K升到932 K.利用实验得出的片状金属的质量(0.015～0.025 g)推算出样品在400r/min球磨时的温度变化范围为845.6～1 409.4 K,使镁粉熔化的最小球磨速度为269 r/min,经400r/min球磨15 h后,Mg-Ni样品由成分不均的晶体相组成,球磨35 h后则转变为成分均匀的非晶体.图4,表2,参5.     

超高速铣削刀具的磨损机理

应用有限元法分析了超高速铣削刀具刀齿的受力和应力，并分析了超高速铣削刀具的热传导特点，根据刀具的受力和热作用分析表明，超高速铣削时最大主应力产生在刀具内周边处，且刀齿的受热过程为一个持续时间极短的热脉冲过程。在此基础上，讨论了超高速铣削刀具的磨损形式和过程．刀具的磨损形式主要有由机械摩擦引起的磨粒磨损、热脉冲应力和力脉冲应力引起的疲劳断裂及粘结磨损，并在刀齿根部产生最终断裂。