Effect of heat treatment on microstructures and properties of a novel Al-Zn-Mg-Cu alloy for oil drilling

In view of the special requirements for strength, heat resistance and corrosion resistance of Al-Zn-Mg-Cu alloy for oil drilling, the Al-6.2 Zn-2.5 Mg-1.6 Cu alloy was prepared by increasing Cu content on basis of Russian Series 1953 alloy. The effect of heat treatment on the microstructures and properties of the alloy was characterized by optical microscope(OM), scanning electron microscope(SEM) and transmission electron microscope(TEM), and investigated by tensile test at room temperature, thermal exposure test and corrosion test. The results show that the strength after T6 aging treatment exhibit a decrease trend as an increase of the solution temperature from465 °C to 480 °C. After the solution treated by the rate of 470 °C/1 h, second phases dissolve into the matrix very well and the strength property reaches optimum. The alloy has better comprehensive properties treated by a solution treatment of 470 °C/1 h and then followed by an aging treatment of 120 °C/24 h + 170 °C/1 h + 120 °C/24 h. Under the aging state, the precipitated phases inside the grains are suitable in size, while on the grain boundary distribute discontinuously and the precipitate-free zone is obvious. Besides, the alloy still maintain high tensile properties. The yield strength, tensile strength and elongation are 650 MPa, 686 MPa,12.0%, respectively. The yield strength retention after heat exposure is 92%. The alloy has good corrosion resistance and the exfoliation corrosion degree. The average corrosion rate in the H_2S and CO_2 environment is 0.0024 mm/a, which is far less than the required 0.12 mm/a. It is insensitive to H_2S and CO_2 environments.     

对摩擦力作功与摩擦生热的量度的认识

本文通过对摩擦力作功与不擦生热的讨论，给出摩擦生热的量度方法．     

DA_1-100型多级自吸离心泵的研制

阐述了多级自吸泵在节能与操作简便方面的实用意义,并且利用外混式自吸原理,将一台普通节段式多级离心泵改造成一台多级自吸离心泵,同时保持了原有的性能和安装尺寸。还分析了两端轴封漏气的原因,并提出了解决的方法。     

双门电冰箱的热传导问题

本文将根据热传导方程,对电冰箱达定态过程进行理论推导,以及定态后电冰箱单位时间吸收的热量,并由此计算出由于冰箱箱体的热量泄漏而消耗的能量。     

金属工件内部残余应力的振动消除研究

本文针对传统的消除金属工作内部残余应力的热时效处理法的不足，从激振角度，运用材料力学、动力学中的振动理论等知识，并通过大量试验验证，研究了振动消除应力的方法－－振动时效法的原理及其有关问题。说明这种新的方法具有节能、高效等一系列优点。     

变量泵电液比例恒压调节器的开发研制

本文利用一种结构新颖的径向柱塞变量汞为基泵,将电液比例技术应用于恒压变量泵的控制上,开发了一种电-液一体化节能液压元件。该电液比例恒压调节器采用“压力直接检测反馈”和“级问动压反馈”两项新原理,改善了泵的非线性度、滞环、恒压误差及其稳定性。文中不仅在理论上分析了泵的结构参数对调节系统的影响,并且实验研究了恒压调节器的三个结构参数对恒压泵动态特性的影响。结果表明,该泵具有优良的静动态性能,可作为恒压源应用于液压系统中,有着显著的节能意义。     

n维空间简谐势阱中理想费米气体的化学势与热容量

采用Ｔｈｏｍａｓ－Ｆｅｒｍｉ的半经典近似方法,得到处于ｎ维空间简谐势阱中的理想费米气体的化学势和热容量等物理量的通用表示式,并讨论了空间维数和外势对这些物理量的影响     

轴流式强制循环泵的选型设计

分析系流量太小的原因，提出选型设计参数的确定方法，并介绍了吸入室流道的改进设计方案及密封型式的选择．     

稳态热流计法导热仪测试人造板导热系数

叙述了稳态热流计法导热仪测试人造板导热系数的原理和方法，讨论分析和比较了两种人造板的测试结果。结果表明：稳态热流计法导热仪具有稳定时间短、测试方便等优点，可用于测定固体材料、纤维材料和多孔隙材料的导热系数。