双通道多感知卷积神经网络图像超分辨率重建

基于深度卷积神经网络的单幅图像超分辨率重建取得了显著研究成果.但随着深度卷积神经网络规模的不断扩大，如何降低网络构建难度和计算成本成为一个难点.为此，提出了一种双通道多感知卷积神经网络(DMCN)模型.该模型在两条具有不同卷积核的通道上建立了稠密连接，并构建了带有动态调节能力的层间融合结构.这种结构的设计使得小规模卷积神经网络便能获得图片特征信息的全面感知能力.实验结果表明，DMCN重建效果优于目前多数具有代表性的重建算法.     

准苏吉花斑岩型钼铜矿床岩体特征及成矿机制研究

通过对辉钼矿的Re-Os及锆石U-Pb同位素年代学研究, 得到辉钼矿的Re-Os等时线年龄为297.2±4.3 Ma, 赋矿花岗斑岩的锆石U-Pb年龄为 301.1±4.0 Ma, 确定准苏吉花斑岩型钼铜(Mo-Cu)矿床的成岩成矿时代为晚石炭世至早二叠世。准苏吉花矿区不含矿花岗闪长岩的锆石U-Pb 年龄为301.2±2.2 Ma, 与花岗斑岩成岩时代一致。发育角闪石和黑云母的矿物学特征以及高Rb, Th和Ba, 低P和Ti的岩石地球化学特征表明, 花岗斑岩和花岗闪长岩同属于I型花岗岩。较低的Re含量、Mg#值、Nb/Ta值和Zr/Hf值以及低ISr值和正ε_Nd(t)值的全岩Sr-Nd同位素特征表明, 准苏吉花花岗岩的源区为新生下地壳的部分熔融, 岩浆演化过程中, 花岗斑岩和花岗闪长岩均经历较强烈的分离结晶作用, 有利于Mo进一步在残余熔体中富集。通过锆石的Ce⁴⁺/Ce³⁺值计算获得岩浆结晶分异时的氧逸度, 发现花岗斑岩岩浆的氧逸度相对较高(ΔFMQ平均值为+4.8), 花岗闪长岩岩浆氧逸度相对较低(ΔFMQ平均值为+2.2), 表明高氧逸度的岩浆更有利于Mo和Cu富集成矿。     

Processing and characterization of the microstructure and mechanical properties of Al6061–TiB2 composite

In the present research, aluminum metal matrix composites were processed by the stir casting technique. The effects of TiB2 rein-forcement particles, severe plastic deformation through accumulative roll bonding (ARB), and aging treatment on the microstructural charac-teristics and mechanical properties were also evaluated. Uniaxial tensile tests and microhardness measurements were conducted, and the micro-structural characteristics were investigated. Notably, the important problems associated with cast samples, including nonuniformity of the rein-forcement particles and high porosity content, were solved through the ARB process. At the initial stage, particle-free zones, as well as particle clusters, were observed on the microstructure of the composite. However, after the ARB process, fracturing phenomena occurred in brittle ceramic particles, followed by breaking down of the fragments into fine particles as the number of rolling cycles increased. Subsequently, com-posites with a uniform distribution of particles were produced. Moreover, the tensile strength and microhardness of the ARB-processed com-posites increased with the increase in the reinforcement mass fraction. However, their ductility exhibited a different trend. With post-deforma-tion aging treatment (T6), the mechanical properties of composites were improved because of the formation of fine Mg2Si precipitates.     

基于40Cr高温动态力学性能的磨削表面动态再结晶行为

通过分离式霍普金森压杆(SHPB)实验得到了40Cr合金钢在高温高应变率下真应力-真应变曲线，据此确定了材料发生动态再结晶的临界条件.采用解析法和实验法分别求解了磨削强化层的温度场和塑性应变场分布.结果表明，磨削强化层在磨削深度方向具有较大的温度和塑性应变梯度;150μm强化层内会发生奥氏体转变;磨削表面最高温度可达1060℃.在磨削亚表面60μm内会产生剧烈的塑性变形，达到了再结晶的临界条件.较大的磨削深度使磨削强化层塑性应变增大，再结晶现象越充分，微观组织细化程度越高.     

可控变胞码垛机器人控制系统设计及实验

为了提高变胞式工业机器人在实际工业生产中的效率以及稳定性,基于可控变胞码垛机器人设计了一种新型的码垛路径运行方式,对其进行运动学仿真并设计了相应的控制系统.其中控制系统采用"运动控制卡+工控机"的上下位机控制模式,使用闭环步进电机及驱动器组成机器人的运动系统,使用光电开关、气动插销及电磁离合器等硬件组成变胞动作执行系统,引入电机脉冲补偿值以减少变胞前后的运动误差.提出新型码垛路径的实现方法,并搭建机器人控制系统,以6 kg负载进行实验,测试结果显示理论位移与实测位移之间的误差不超过0.6 mm.研究表明该控制系统运行安全可靠,能够满足可控变胞码垛机器人的控制要求,同时也为变胞式工业机器人的控制系统设计提供了参考.     

基于成像算子优化的微震逆时定位方法

针对目前微震逆时定位成像存在的问题,提出一种优化后的成像算子,对模型数据进行抗噪性、误差速度以及检波器分布和数量进行测试,并提出采用峰度值作为定位成像结果的评价标准。结果表明,优化后的成像条件在定位能量聚焦程度和成像分辨率上都得到了提升,对含速度误差和含噪微震数据都有较好的成像结果,并且对检波器的分布和数量有较好的适应性,取得了较为理想的定位效果。     

Mechanical behavior of a near α titanium alloy under dynamic compression: Characterization and modeling

Dynamic compression tests under strain rates from 870 s^?1 to 2100 s^?1 were conducted for a near α Ti–8Al–1Mo–1V titanium alloy with equiaxed microstructure. Compression behavior, adiabatic shearing and band microstructure were investigated via characterization and calculation. The results demonstrate that all dynamic constitutive curves exhibited obvious stress fluctuation phenomenon with double increase-decrease changing stages at the primary stage of compression. The dislocation multiplication theory can be used to explain this phenomenon. After the stress fluctuation period, work hardening coexisted with the thermal softening, resulting in the slow hardening tendency in constitutive curves. J-C model was utilized to quantify the dynamic constitutive curves. The deviations between the predicted and experimental curves under high strain rates may be attributed to the over-consideration of thermal softening effect in J-C model. Adiabatic shearing band (ASB) began to form under the strain rate of 2100 s^?1. A total shearing strain of 8.1 within ASB achieved in 8.9 μs, corresponding to a local strain rate of about 9.1 × 10⁵ s^?1 and is over 430 times of the macro strain rate. Post annealing was conducted on ASB before EBSD characterization. Due to the static recrystallization during annealing, the α phase within ASB generally presented as ultra-fine grains less than 1 μm in diameter.     

大物质分选机在餐厨垃圾预处理中的应用

餐厨垃圾预处理阶段物质分选对整体处理工艺影响较大，如果分选不到位，浆料中杂物多，会导致管道磨损严重、设备故障率高等问题。通过调节进料频率及大物质分选机的运行频率，探究大物质分选机较优的运行参数范围，使分选工作更加有效。试验结果表明：大物质分选机运行频率为70 Hz，进料频率小于17 Hz为较优运行参数，此时设备电流值较低且波动曲线较为平稳，分选料中有机质质量占比在33%~37%，与其他工况相比，有机质质量占比至少低了3%；运行工况的变化不会对浆料的组成成分造成影响，其中剩余物、果皮和骨头质量占比较大，三者占比总和在98%以上，其他杂物质量占比不超过2%。     

柴西北缘花土沟地区新近系油砂山组沉积特征及铀源分析

柴北缘花土沟地区新近系油砂山组含铀岩系为绿灰色碎屑岩沉积建造。区域内主要发育扇三角洲、滨浅湖相。含铀岩系受滨浅湖相沉积体系控制。研究区内铀源具有多源性特点,基底和盖层铀丰度较高。通过野外调查实测剖面和编录铀矿调查钻孔发现油砂山组具有泥-砂-泥结构特征,砂层厚度适宜,倾角较缓,属于宽缓的山前斜坡带,有利于含矿砂体及富氧流体进入层间,形成层间氧化带及铀的富集。     

Characterizations of dissimilar S32205/316L welds using austenitic,super-austenitic and super-duplex filler metals

UNS S32205 duplex stainless steel plates were welded to AISI 316L stainless steel using the pulsed gas tungsten arc welding process with three different filler metals: ER2594, ER312, and ER385. The microstructures of the welds were characterized using optical and scanning electron microscopy, and all of the specimens were evaluated by ferrite measurements. The mechanical properties were studied through hardness, tensile, and impact tests. In addition, the pitting resistance equivalent number was calculated and cyclic polarization tests were performed to evaluate the corrosion resistance of the weld metal. The results showed that chromium nitride was formed in the heat-affected zone of the duplex side, whereas no sigma phase was detected in any of the specimens. The ferrite number increased from the root pass to the final pass. The absorbed energies of the impact test decreased with increasing ferrite number, whereas the tensile strength was enhanced. The fully austenitic microstructure of the specimen welded with ER385 exhibited the highest resistance to pitting corrosion at 25°C, and the super-duplex weld metal presented superior corrosion resistance at 50°C.