Microwave quantum logic gates for trapped ions

Control over physical systems at the quantum level is important in fields as diverse as metrology, information processing, simulation and chemistry. For trapped atomic ions, the quantized motional and internal degrees of freedom can be coherently manipulated with laser light. Similar control is difficult to achieve with radio-frequency or microwave radiation: the essential coupling between internal degrees of freedom and motion requires significant field changes over the extent of the atoms' motion, but such changes are negligible at these frequencies for freely propagating fields. An exception is in the near field of microwave currents in structures smaller than the free-space wavelength, where stronger gradients can be generated. Here we first manipulate coherently (on timescales of 20 nanoseconds) the internal quantum states of ions held in a microfabricated trap. The controlling magnetic fields are generated by microwave currents in electrodes that are integrated into the trap structure. We also generate entanglement between the internal degrees of freedom of two atoms with a gate operation suitable for general quantum computation; the entangled state has a fidelity of 0.76(3), where the uncertainty denotes standard error of the mean. Our approach, which involves integrating the quantum control mechanism into the trapping device in a scalable manner, could be applied to quantum information processing, simulation and spectroscopy.     

Effect of deep cryogenic treatment on the formation of nano-sized carbides and the wear behavior of D2 tool steel

The effect of deep cryogenic treatment on the microstructure, hardness, and wear behavior of D2 tool steel was studied by scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), hardness test, pin-on-disk wear test, and the reciprocating pin-on-flat wear test. The results show that deep cryogenic treatment eliminates retained austenite, makes a better carbide distribution, and increases the carbide content. Furthermore, some new nano-sized carbides form during the deep cryogenic treatment, thereby increasing the hardness and improving the wear behavior of the samples.     

Effect of deep cryogenic treatment on the properties of 80CrMo12 5 tool steel

The effect of deep cryogenic treatment on the mechanical properties of 80CrMo12 5 tool steel was investigated. Moreover, the effects of stabilization (holding at room temperature for some periods before deep cryogenic treatment) and tempering before deep cryogenic treatment were studied. The results show that deep cryogenic treatment can eliminate the retained austenite, making a better carbide distribution and a higher carbide amount. As a result, a remarkable improvement in wear resistance of cryogenically treated specimens is observed. Moreover, the ultimate tensile strength increases, and the toughness of the sample decreases. It is also found that both stabilization and tempering before deep cryogenic treatment decrease the wear resistance, hardness, and carbides homogeneity compared to the deep cryogenically treated samples. It is concluded that deep cryogenic treatment should be performed without any delay on samples after quenching to reach the highest wear resistance and hardness.     

Real-time quantum feedback prepares and stabilizes photon number states

Feedback loops are central to most classical control procedures. A controller compares the signal measured by a sensor (system output) with the target value or set-point. It then adjusts an actuator (system input) to stabilize the signal around the target value. Generalizing this scheme to stabilize a micro-system's quantum state relies on quantum feedback, which must overcome a fundamental difficulty: the sensor measurements cause a random back-action on the system. An optimal compromise uses weak measurements, providing partial information with minimal perturbation. The controller should include the effect of this perturbation in the computation of the actuator's operation, which brings the incrementally perturbed state closer to the target. Although some aspects of this scenario have been experimentally demonstrated for the control of quantum or classical micro-system variables, continuous feedback loop operations that permanently stabilize quantum systems around a target state have not yet been realized. Here we have implemented such a real-time stabilizing quantum feedback scheme following a method inspired by ref. 13. It prepares on demand photon number states (Fock states) of a microwave field in a superconducting cavity, and subsequently reverses the effects of decoherence-induced field quantum jumps. The sensor is a beam of atoms crossing the cavity, which repeatedly performs weak quantum non-demolition measurements of the photon number. The controller is implemented in a real-time computer commanding the actuator, which injects adjusted small classical fields into the cavity between measurements. The microwave field is a quantum oscillator usable as a quantum memory or as a quantum bus swapping information between atoms. Our experiment demonstrates that active control can generate non-classical states of this oscillator and combat their decoherence, and is a significant step towards the implementation of complex quantum information operations.     

Investigation of the stress rupture behavior of GTD-111 superalloy melted by VIM/VAR

The effects of vacuum induction melting (VIM) and vacuum arc remelting (VAR) processes on the microstructure and stress rupture properties of Ni-based GTD-111 superalloy were investigated. Samples of GTD-111 master alloy were melted in VIM and VAR furnaces and then poured into a preheated ceramic mold for VIM melt or into a water-cooled copper mold for VAR melt. The as-cast samples were examined radiographically to ensure that no casting defects were present in the final castings; the samples were then heat-treated using a standard heat-treatment cycle. The microstructure of the samples was investigated using optical microscopy and scanning electron microscopy in conjunction with energy-dispersive X-ray spectroscopy for microanalysis. On the basis of standard ASTM-E139, stress rupture tests were carried out at 1000℃ under a stress of 300 MPa. The results showed that a γ matrix, fine γ' precipitates, a γ-γ' eutectic structure, carbide particles, and some harmful phases such as σ and η phases were present in the as-cast samples. The γ' precipitates with cubic morphology appeared in the matrix after the standard heat-treatment process. The extent of segregation and the amount of γ-γ' eutectic structure formed in the VAR-prepared sample were less than in the VIM-prepared sample. The results of stress rupture tests showed that the rupture time for the VAR sample was 43% longer than that for the VIM sample.