一种改进的基于人体静电冲击模型应力的瞬态功率模型

提出一种改进的基于人体静电冲击模型(Human Body Model, HBM)应力的瞬态功率模型。利用HSPICE仿真软件, 模拟MOS管遭受的HBM应力, 得到对应的等效直流电压。HBM电路的预充电电压与MOS管对应的等效直流电压值的散点图表明, 两者保持线性关系, 并通过拉普拉斯变化得到证明。与现有的瞬态功率模型相比, 改进后的模型降低了在HBM应力作用下的计算复杂度, 可以更加简便地从统计学上预测MOS管栅氧击穿的发生, 给HBM冲击作用下MOS管栅氧化层可靠性的评估提供参考。     

Acyl-chloride functionalized graphene oxide chemically grafted with hindered phenol and its application in anti-degradation of polypropylene

In this study,graphene oxide (GO) nanosheets were first functionalized by the acyl-chloride reaction and then reacted with hindered phenol (HP) to obtain HP grafted GO (GO-g-HP).The GO-g-HP prepared under the optimized condition exhibited a high efficiency against both thermal and photo oxidation of isotactic polypropylene (iPP).GO-g-HP exhibited a much better anti-aging efficiency than that of HP and GO used individually or that of their physical mixture.The outstanding anti-aging effect of GO-g-HP was attributed to the excellent synergistic effect produced between the chemically bonded GO and HP,which resulted in an improved oxygen barrier property of GO and excellent utilization of the free radical scavenging capability of GO and HP.Also,thanks to the grafting of HP on GO,the physical loss of HP,which was one of the main shortcomings for traditional small molecular antioxidants,was largely suppressed.It is expected that the GO-g-HP prepared can well meet the requirement of long-term applications of polymers in some harsh service conditions.     

Effect of Yb2O3 doping on the grain boundary of NiFe2O4–10NiO-based cermets after sintering

xYb2O3–15(20Ni–Cu)/(85?x)(NiFe2O4–10NiO) (x=0, 0.25, 0.5, 0.75, 1.0, 2.0, and 10.0) cermets for aluminum electrolysis were prepared to investigate the effect of Yb2O3 doping on the grain boundary of the cermets after sintering. The results showed that each interface was very clear and that with increasing Yb2O3 content, most of the Yb was evenly distributed at the grain boundary. Moreover, according to the phase composition and microstructural analysis by X-ray diffraction (XRD), scanning electron microscopy with energy dispersive X-ray spectroscopy (SEM/EDX), and electron probe microanalysis (EPMA), YbFeO3 was produced along the grain boundary. The YbFeO3 was concluded to not only have formed from the interaction between the NiFe2O4 or Fe2O3 component and Yb2O3 at the grain boundary of the cermets, but also from the decomposition of NiFe2O4 into NiO and Fe2O3 and the subsequent reaction of Fe2O3 with Yb2O3. Thus, the pro-duction of YbFeO3 resulted in a cermet with high relative density, good electrical conductivity, and good corrosion resistance.     

碘化钾催化CO_2与氧化苯乙烯合成苯乙烯环状碳酸酯条件的优化

用碘化钾催化CO2与氧化苯乙烯(SO)合成苯乙烯环状碳酸酯,分别从溶剂、催化剂用量、温度、CO2压力和反应时间进行探讨,得出了最佳条件.结果表明:以无水乙醇为溶剂,催化剂用量r(KI∶SO)=1∶250,在170℃,CO2压力5 MPa,反应时间5 h,苯乙烯环状碳酸酯的产率和选择性均达到100%.     

硼酸钙/氧化石墨烯复合微粒的制备及摩擦学性能研究

以硼砂、硝酸钙和氧化石墨烯为原料利用水热技术制备硼酸钙/氧化石墨烯复合微粒.利用透射电镜(TEM)、X-射线衍射(XRD)和能谱(EDS)对硼酸钙/氧化石墨烯复合微粒形貌、结构及磨痕表面进行表征.将复合微粒用油酸修饰并添加到液体石蜡中,利用四球摩擦试验机分析其摩擦学性能,结果表明:复合微粒添加剂具有良好的减摩抗磨性能.     

氧化钨纳米棒的制备及其形貌控制

报道了一种利用溶胶-凝胶法和水热法相结合制备纳米氧化钨的新方法.首先在丙醇-四丁基溴化铵-环己烷体系中,由钨酸钠和盐酸反应出发制备凝胶状的钨酸,然后将其置于高压反应釜中200℃下处理12 h即可制得氧化钨纳米棒.使用X-射线衍射分析仪(XRD)和扫描电子显微镜(SEM)对产物的结构与形貌进行表征.     

烧结温度对高速压制制备弥散强化铜材料导电率的影响

弥散强化铜材料具有高强度和高导电性的特性,孔洞是影响导电率的重要因素.本文采用高速压制成形技术,对Al2 O3质量分数为0.9%的弥散强化铜粉压制成形,研究了压制速度对生坯的影响.当压制速度为9.4 m·s-1时得到密度为8.46 g·cm-3的生坯.研究了烧结温度对烧结所得Al2 O3弥散强化铜试样导电率的影响.当生坯密度相同时,烧结温度越高,所得试样的导电率也越高.断口与金相分析表明：烧结温度为950℃时,烧结不充分,颗粒边界以及孔洞多而明显,孔洞形状不规则;烧结温度为1080℃时,颗粒边界消失,孔洞圆化,韧窝出现,烧结坯的电导率为71.3%IACS.     

由铁鳞制备纳米氧化铁可见光光催化剂

以铁鳞为原料,采用水热法成功制备不同形貌的纳米Fe2 O3光催化剂。探讨了不同浓度的盐酸、液固比及反应时间对铁鳞浸出规律的影响。系统研究了铁鳞浸出液的纯度对于水热法制备纳米Fe2 O3的微观形貌和光催化性能的影响。结果表明：8 g铁鳞与150 mL浓度为3 mol·L-1的盐酸溶液在100℃回流反应2 h,铁鳞的浸出率达到约93%且浸出液纯度较高。浸出液中的杂质离子改变了纳米Fe2 O3的微观形貌和晶体的择优生长方向。另外,以铁鳞为原料制备出的纳米Fe2 O3可见光光催化性能较好,光降解罗丹明B溶液60 min后,其降解率可达87%左右。