分布式声传感器井中背景噪声统计特性分析

分布式声传感器技术(DAS: Distributed Acoustic Sensor)是一种新近提出的高精度勘探数据采集方法,受制于复杂背景噪声的影响,DAS记录处理水平有待进一步提高.针对上述问题,采用基于替代序列的时间序列平稳性检验方法和Lilliefors检验法对DAS记录中复杂背景噪声的平稳性和高斯性进行研究.用以分析的实际地震数据是按照勘探工业要求采集的井中DAS记录.研究结果表明,DAS背景噪声是非平稳、非高斯随机过程且噪声特性随记录时长发生变化.相关研究成果实现了针对DAS背景噪声特性的可靠认知,对提高DAS记录处理水平具有重要参考价值.     

四川盆地碳酸盐岩源岩气地质特征与勘探前景

充分利用露头、岩芯、岩屑等原始样品，通过薄片观察、物性分析、扫描电镜、X射线衍射及同位素分析等实验方法，结合测井资料、地震剖面解释等进行研究，从碳酸盐岩源岩气地球化学评价参数和指标厘定入手，以南川区带高产稳产气藏为实例，深入解剖四川盆地茅口组一段碳酸盐岩源岩的岩矿、物性、电性、含气性及生烃潜力，探讨了表生沉积环境、早期成岩作用等因素对碳酸盐岩源岩气储层的影响，尤其是富镁黏土矿物黑滑石在碳酸盐岩中有机质富集、碳酸盐岩气成生和聚集的积极作用，进一步明确气藏高产稳产的主控因素，落实“甜点段”的特征和分布，指明了该领域勘探开发的前景。     

水热法制备不同形貌纳米片状MoS_2的光催化性能

二硫化钼是类似于石墨烯的二维层状材料,其优异的磁学性能、电学性能、催化性能和光学性能受到了科研人员的广泛关注.通过水热法制备出4种不同形貌的二硫化钼纳米片.对二硫化钼样品进行扫描电子显微镜测试,以200 W钨丝灯为光源,在暗箱中进行甲基橙溶液的降解测试.通过紫外可见光分光光度计对测试样品溶液进行吸光度测试,得出纳米片状的二硫化钼光催化降解甲基橙溶液降解率最高.     

w(Co)对CB2钢显微组织和力学性能的影响

为研究w(Co)对CB2钢微观组织和力学性能的影响，调整CB2钢中w(Co)为0.5%，1.0%，1.5%，2.0%和3.0%.利用光学显微镜(OM)、扫描电镜(SEM)、室温拉伸等检测方法研究w(Co)对试验钢微观组织和力学性能的影响规律，结合Thermo-Calc和JMatpro-7.0模拟结果解释其影响机理.研究发现:w(Co)增加提高铬当量的值，使试验钢中δ铁素体含量减少，当w(Co)增加到1.5%时，δ铁素体基本消失;材料的抗拉强度随w(Co)的增加而增加，而延长率则先增加后降低;结果表明，w(Co)为1.5%时综合性能较好，即抗拉强度达到805.13MPa，延长率达到20.4%，布氏硬度为260.     

多主元FeNiMnCr0.75Alx高熵合金微观结构和力学性能的研究

研究了合金中Al含量的增加对铸态FeNiMnCr_0.75Al_x（x=0.25，0.5，0.75，原子分数）高熵合金晶体结构及力学性能的影响。采用X射线衍射仪（XRD）和透射电子显微镜（TEM）对合金的微观结构及形貌进行分析，采用维氏硬度计和MTS万能试验机测试合金的硬度和室温压缩性能。试验结果表明，铸态下，FeNiMnCr_0.75Al_x高熵合金均由bcc和fcc两种晶体结构的相构成。随着Al含量的增加，合金中bcc结构的相的相对含量逐渐增加，导致硬度和压缩屈服强度也随之升高，应变量降低；且Al含量的增加最终也促使合金中无序bcc结构的相逐渐转变为Ni：（Mn+Al）=1：1（原子分数比）型有序bcc结构的相。     

Ti-1300钛合金挤压管材组织性能研究

通过室温拉伸测试和显微组织观察，研究了挤压温度和热处理工艺对Ti-1300钛合金挤压管材显微组织和力学性能的影响，讨论了热加工工艺、显微组织和力学性能之间的关系。结果表明：Ti-1300钛合金在两相区挤压后的横向组织均匀细小，纵向组织沿挤压加工流线破碎均匀；其拉伸强度高达1 445 MPa。管材在相变点以上的高温固溶组织主要由等轴β相晶粒组成，具有较好的塑性。合金两相区挤压后具有较好的强度和塑性的匹配，两相区挤压的塑性明显优于β单相区挤压，尤其面缩。试样经过固溶时效处理后显微组织明显细化，强度大幅度提高，可达1 300 MPa以上。     

循环作用对马蹄寺石窟群岩体性能的影响

马蹄寺石窟群地处河西走廊中部,气候条件十分恶劣。由于常年受到温度、湿度、酸碱盐等作用的影响,石窟岩体性能出现了不同程度的劣化现象。通过开展室内模拟试验,研究以上多种恶劣环境的循环作用对于岩体抗压强度、波速、质量的影响规律,同时使用X射线衍射仪(X-ray diffraction,XRD)、X射线荧光光谱(X-ray fluorescence,XRF)和扫描电子显微镜(scanning electron microscope,SEM)对循环作用过程中样品的矿物组分、元素含量和微观形貌进行分析研究。研究结果表明,循环作用使样品中的长石类矿物和方解石含量降低,黏土类矿物含量增加,胶结程度下降,孔隙逐渐发展成为横向微裂隙,导致样品的性能出现不同程度的劣化现象。循环作用对岩体性能的影响程度从大到小依次为冻融循环、耐盐循环、耐碱循环、耐酸循环和温湿循环。     

Effect of heat treatment on microstructures and properties of a novel Al-Zn-Mg-Cu alloy for oil drilling

In view of the special requirements for strength, heat resistance and corrosion resistance of Al-Zn-Mg-Cu alloy for oil drilling, the Al-6.2 Zn-2.5 Mg-1.6 Cu alloy was prepared by increasing Cu content on basis of Russian Series 1953 alloy. The effect of heat treatment on the microstructures and properties of the alloy was characterized by optical microscope(OM), scanning electron microscope(SEM) and transmission electron microscope(TEM), and investigated by tensile test at room temperature, thermal exposure test and corrosion test. The results show that the strength after T6 aging treatment exhibit a decrease trend as an increase of the solution temperature from465 °C to 480 °C. After the solution treated by the rate of 470 °C/1 h, second phases dissolve into the matrix very well and the strength property reaches optimum. The alloy has better comprehensive properties treated by a solution treatment of 470 °C/1 h and then followed by an aging treatment of 120 °C/24 h + 170 °C/1 h + 120 °C/24 h. Under the aging state, the precipitated phases inside the grains are suitable in size, while on the grain boundary distribute discontinuously and the precipitate-free zone is obvious. Besides, the alloy still maintain high tensile properties. The yield strength, tensile strength and elongation are 650 MPa, 686 MPa,12.0%, respectively. The yield strength retention after heat exposure is 92%. The alloy has good corrosion resistance and the exfoliation corrosion degree. The average corrosion rate in the H_2S and CO_2 environment is 0.0024 mm/a, which is far less than the required 0.12 mm/a. It is insensitive to H_2S and CO_2 environments.     

Processing and characterization of the microstructure and mechanical properties of Al6061–TiB2 composite

In the present research, aluminum metal matrix composites were processed by the stir casting technique. The effects of TiB2 rein-forcement particles, severe plastic deformation through accumulative roll bonding (ARB), and aging treatment on the microstructural charac-teristics and mechanical properties were also evaluated. Uniaxial tensile tests and microhardness measurements were conducted, and the micro-structural characteristics were investigated. Notably, the important problems associated with cast samples, including nonuniformity of the rein-forcement particles and high porosity content, were solved through the ARB process. At the initial stage, particle-free zones, as well as particle clusters, were observed on the microstructure of the composite. However, after the ARB process, fracturing phenomena occurred in brittle ceramic particles, followed by breaking down of the fragments into fine particles as the number of rolling cycles increased. Subsequently, com-posites with a uniform distribution of particles were produced. Moreover, the tensile strength and microhardness of the ARB-processed com-posites increased with the increase in the reinforcement mass fraction. However, their ductility exhibited a different trend. With post-deforma-tion aging treatment (T6), the mechanical properties of composites were improved because of the formation of fine Mg2Si precipitates.     

准噶尔盆地乌伦古坳陷中南部石炭系烃源岩生烃潜力分析

目前已在准噶尔盆地乌伦古坳陷石炭系、二叠系、三叠系和侏罗系等发现了工业油气流或油气显示，这些油气主要来源于石炭系烃源岩。但目前研究区石炭系有效烃源岩分布及生烃演化特征不清楚。笔者对比分析了研究区石炭系不同层段、不同岩性类型烃源岩的生烃潜力和热演化特征。结果表明：巴塔玛依内山组凝灰质泥岩、泥岩和姜巴斯套组炭质泥岩有机质丰度较高，有机质类型以Ⅱ2—Ⅲ型为主，处于成熟—过成熟演化阶段，具有倾气性特征。综合应用地球化学实验数据得出姜巴斯套组烃源岩都是有效气源岩，而目前钻井揭示巴塔玛依内山组烃源岩成熟度偏低，未能达到有效气源岩的标准。通过系统对比研究区与滴水泉凹陷石炭系烃源岩地球化学参数，认识到两地区具有高度相似性。可见准噶尔盆地乌伦古坳陷中南部石炭系姜巴斯套组是一套极具潜力的烃源岩，为下一步油气勘探指明方向。