ZrO2添加量对等离子放电烧结制备WC-6Co组织和性能的影响

以WC-6Co为主体原料，通过添加不同含量的ZrO₂作为烧结助剂，采用SPS烧结技术制备出性能出众的WC-6Co硬质合金，研究了ZrO₂烧结助剂对硬质合金显微组织及力学性能的影响规律.结果表明:随着ZrO₂添加量的增加，试样的显微组织更加致密，相对密度更大，硬度和断裂韧性也有一定程度的增加.并且，当添加ZrO₂的质量分数为3%时，试样的相对密度达到96.7%，维氏硬度增加到20.28kN·mm^-2，断裂韧性增长到12.7MPa·mm^1/2，综合性能最优.研究发现，ZrO₂可以通过促进离子的扩散和颗粒的重排促进烧结，最终使得材料的相对密度和性能均得到提升.     

辅助离子束对孪生磁场中频反应溅射等离子体特性的影响

 在自行研制的离子束辅助孪生磁场中频反应溅射设备中制备光学氧化钛薄膜，利用郎缪尔静电探针研究等离子特性变化，同时测定基片表面的伏安（I-V）特性。结果表明，随离子束功率密度不断提高，等离子体电子密度不断增加，悬浮负电位绝对值减小，溅射阴极电压下降；基片表面经历从富电子向富阳离子转变，基片正电位不断提高；辅助离子束为109 W时，基片表面处于电中性等离子体平衡态。     

A TEM study on the microstructure of spark plasma sintered ZrB_2-based composite with nano-sized SiC dopant

Sintering behavior of ZrB_2 ceramic with nano-sized SiC dopant was studied. ZrB_2-25 vol% nano-sized SiC was selected as the starting mixture to fabricate the composite. The manufacturing process was accomplished at 1800℃ for 5 min under 25 MPa via spark plasma sintering(SPS). The as-sintered sample reached a relative density of 99%. Besides the initial phases, namely ZrB_2 and SiC, the high-resolution X-ray diffraction(HRXRD) was used to study the formation of an in-situ ZrC phase. The possible chemical interactions during the ZrC phase formation were scrutinized. The microstructure of the composite was studied by the field emission scanning electron microscopy(FESEM) and transmission electron microscopy(TEM). Elemental analysis through FESEM evaluations revealed the formation of amorphous phases, rich in Zr, C, Si, B, and O elements, which was in harmony with the thermodynamical assessments. TEM studies endorsed the formation of such phases, containing a glassy bed of Si–B–O with ZrC and C islands dispersed therein.     

ICP-MS法测定钼矿石中伴生锂、镓和稀土元素

通过比较氢氟酸-硝酸高压罐密闭消解法、 氢氟酸-硝酸-高氯酸-盐酸低压密闭消解法和氢氟酸-硝酸-高氯酸-盐酸敞口消解法对钼矿样品的分解效果， 选用低压密闭消解法制备样品， 用电感耦合等离子体质谱（ICP-MS)法测定伴生稀有元素Li，Ga和15种稀土元素的质量比. 通过对干扰元素的分析， 选择合适同位素， 并确定¹⁵¹Eu，¹⁵⁷Gd，¹⁵⁹Tb质谱干扰的校正系数. 结果表明，  20 μg/L的铑（Rh）标准溶液作为内标可有效抑制溶液中的基体效应和信号动态漂移， 方法检出限为0.001~0.113 μg/g， 相对标准偏差（RSD， n=7）为0.30%~3.92%.  经标准物质和实际样品验证， 该方法可靠， 适合钼矿中伴生Li，Ga和稀土元素的测定.     

Plasma preparation and low-temperature sintering of spherical TiC–Fe composite powder

A spherical Fe matrix composite powder containing a high volume fraction (82vol%) of fine TiC reinforcement was produced us-ing a novel process combining in situ synthesis and plasma techniques. The composite powder exhibited good sphericity and a dense struc-ture, and the fine sub-micron TiC particles were homogeneously distributed in theα-Fe matrix. A TiC–Fe cermet was prepared from the as-prepared spherical composite powder using powder metallurgy at a low sintering temperature;the product exhibited a hardness of HRA 88.5 and a flexural strength of 1360 MPa. The grain size of the fine-grained TiC and special surface structure of the spherical powder played the key roles in the fabrication process.     

电镜成像方式对数字散斑相关方法结果的影响

研究了扫描电镜成像方式对数字散斑相关方法计算结果的影响,在此基础上对等离子喷涂铜涂层的变形场进行分析。结果表明二次电子成像和背散射电子成像的机理不同,应用时需要以相关系数及其标准差为标准,选取更为合适的成像方式。通过数字散斑相关方法显化了等离子喷涂铜涂层在加载过程中的应变场,结果表明随加载力增加,裂纹尖端应变场逐渐由蝴蝶状区域转为圆形钝化区。     

助滤剂对电解锰渣的助滤作用研究

针对锰渣滤饼含水率高的问题,通过在酸性浸出液中加入助滤剂来解决.通过酸性浸出液中锰渣的粒度,润湿性分析,发现锰渣粒度细和表面呈亲水性导致含水率高.根据锰渣的主要成分SiO₂和接触角试验,最后确定油酸酰胺、十八胺和十二胺作为助滤剂进行抽滤试验.结果表明:油酸酰胺对降低锰渣滤饼的含水率效果不佳,十八胺和十二胺效果显著.建立十八胺和十二胺用量对含水率作用的回归方程,确定十八胺用量为2514.47 g·m^-3时,含水率最低为36.10%,十二胺用量为1894.57 g·m^-3时,含水率最低为34.09%.因此,确定十二胺为锰渣的助滤剂.     

血浆sST2联合NT-proBNP对急诊心衰患者生存状况的预测价值

目的探讨血浆sST2联合NT-proBNP对急诊心衰患者生存状况的预测价值.方法选择急诊心衰患者130例,分为心功能Ⅱ级组、心功能Ⅲ~Ⅳ级组,对照组选择健康的体检者60例.对3组NT-proBNP及血浆sST2水平进行观察对比,对心功能不同分级患者NT-proBNP及血浆sST2水平进行比较,比较NT-proBNP,sST2,NTproBNP联合血浆sST2对心衰患者死亡状况的预测价值.结果随心功能分级递增,NT-proBNP水平逐渐升高,sST2曲线下面积(0.776)及NT-proBNP对死亡判定的ROC曲线与NT-proBNP曲线下面积(0.775)相比较没有明显差异,但二者联合曲线下面积为0.813,与NT-proBNP及sST2曲线下面积相比较差异显著.sST2联合NTproBNP进行心衰患者死亡状况预测时的敏感度为99.0%,特异度为93.2%.结论作为急诊心衰患者诊断、预后和风险评估的主要标志物,sST2联合NT-proBNP对患者生存状况进行评估可以很好地预测患者的生存状况,提高准确度和敏感度,值得在临床上推广应用.     

化学平衡化的夸克-胶子等离子体中产生的双轻子的横向质量谱

研究了s=200 GeV能量下^197Au＋^197Au的对心碰撞,并在化学平衡化的夸克-胶子等离子体中计算了双轻子的横向不变质量谱,从中提取斜率即温度,发现其对双轻子的不变质量有近似线性的增函数关系.这种增函数关系不仅是系统径向流影响的结果,还包含了双轻子的不变质量与其产生源温度之间的增函数关系的影响.     

Bluff body flow-induced noise control with sliding plasma actuators

Sliding plasma actuators were used to control the flow-induced broadband noise radiating from a bluff body. The structure consisted of a cylinder and a torque link that was installed on the lee side of the cylinder. The objective was to reduce the noise generated during the cylinder wake impinging on the torque link. By manipulating cylinder wake with the externally-imposed body force generated by the plasma actuators, the flow-structure interaction was reduced, leading to an attenuation of the broadband noise up to 3 dB in overall sound pressure level at a free stream speed of 30 m/s.