全文获取类型
收费全文 | 397篇 |
免费 | 28篇 |
国内免费 | 13篇 |
专业分类
丛书文集 | 15篇 |
现状及发展 | 1篇 |
综合类 | 422篇 |
出版年
2024年 | 1篇 |
2023年 | 5篇 |
2022年 | 3篇 |
2021年 | 6篇 |
2020年 | 7篇 |
2019年 | 5篇 |
2018年 | 5篇 |
2017年 | 11篇 |
2016年 | 16篇 |
2015年 | 16篇 |
2014年 | 13篇 |
2013年 | 16篇 |
2012年 | 25篇 |
2011年 | 25篇 |
2010年 | 17篇 |
2009年 | 14篇 |
2008年 | 16篇 |
2007年 | 19篇 |
2006年 | 11篇 |
2005年 | 18篇 |
2004年 | 20篇 |
2003年 | 12篇 |
2002年 | 13篇 |
2001年 | 14篇 |
2000年 | 16篇 |
1999年 | 18篇 |
1998年 | 11篇 |
1997年 | 17篇 |
1996年 | 9篇 |
1995年 | 6篇 |
1994年 | 14篇 |
1993年 | 6篇 |
1992年 | 5篇 |
1991年 | 10篇 |
1990年 | 5篇 |
1989年 | 3篇 |
1988年 | 4篇 |
1987年 | 2篇 |
1986年 | 3篇 |
1985年 | 1篇 |
排序方式: 共有438条查询结果,搜索用时 15 毫秒
1.
采用JSM-6480扫描电子显微镜(scanning electron microscope,SEM)、Wilson Tukon 1102维氏硬度计研究了时效处理对17-7PH不锈钢微观组织和维氏硬度的影响。结果表明:17-7PH不锈钢经过0 ℃/30 min深冷处理后,在560 ℃进行时效处理,随着时效时间的延长,维氏硬度逐渐降低,未进行时效处理时的维氏硬度最高,为481;-73 ℃/8 h深冷处理后,再510 ℃/30 min时效处理,达到峰值时效硬度,维氏硬度为500,继续延长时效时间,维氏硬度逐渐降低。 相似文献
2.
为了解决ZL205A合金铸件产生偏析缺陷等问题,进一步明确振动对偏析组织及硬度的影响规律,采用电磁式振动台作为振动源,探究了振动频率、振幅、振动时间对合金偏析组织占比及硬度的影响情况。结果表明,振动频率在25~55 Hz内变化时,随着振动频率的增加,偏析组织占比呈现先减小、后增加的趋势,硬度呈现先增大、后减小的趋势;振幅由1 mm增加到4 mm的过程中,偏析组织占比逐渐减少并趋于稳定,硬度呈现先减小、后增大的趋势;振动时间由30 s增加至75 s时,偏析组织占比呈现增加趋势并最终趋于稳定,硬度呈现先减小、后增大的趋势。振动频率对合金偏析组织和硬度的影响最为显著,振动时间和振幅的影响次之,此外,偏析组织的析出也会影响合金硬度。研究结果为明确ZL205A合金在振动条件下凝固组织的变化规律、提高铸件质量提供了理论参考。 相似文献
3.
采用辉光离子渗N技术对奥氏体不锈钢球阀进行表面氮化处理,改变其表面结构,提高表面耐磨性.选取三组离子渗N的温度,分别为400、440、480 ℃,渗N时间设置为12 h.采用扫描电镜、光学显微镜、X射线衍射仪、维氏显微硬度计和材料表面综合测试仪对渗N改性层的表面形貌、截面形貌、显微硬度和耐磨性进行测试.结果表明:离子渗N技术可以大幅提高奥氏体不锈钢的硬度和耐磨性.渗N温度为400 ℃时,渗N改性层最薄,耐磨性最差,480 ℃时渗N改性层最厚、耐磨性最好. 相似文献
4.
5083铝合金表面化学镀Ni-P镀层的力学性能 总被引:1,自引:0,他引:1
采用化学镀方法在5083铝合金基体上制备了Ni-P非晶薄膜,采用纳米压痕技术在不同应变速率下研究Ni-P非晶薄膜的硬度、弹性模量和变形行为.结果表明,Ni-P非晶薄膜硬度不是一个恒定值,与纳米压痕的压入深度有关,而弹性模量基本保持不变;载荷-深度曲线出现跳跃及台阶现象与应变速率有关,应变速率愈慢,曲线出现台阶现象越明显;跳跃台阶源于单个剪切带的开动,而在高的应变速率条件下,由于多个剪切带的开动,曲线上便不出现跳跃台阶. 相似文献
5.
利用弹性模量和硬度的联系,完成了铝合金LY12CZ-M和合金钢30Cr Mn Si A弹性模量随机场相关特性的实验测量及分析。具体工作包括测量试件空间各点的洛氏硬度,并以区域化变量理论中的相关函数为工具对测量数据进行统计分析。分析结果表明:金属材料弹性模量随机场的变异系数在7%左右;随机场的空间连续性较好,不存在块金效应;相关函数模型宜选用单指数型;随机场不同方向上的相关特性几乎相同。 相似文献
6.
基于第一性原理,利用赝势平面波法分析MX型合金化合物的结构性质、弹性性质和力学稳定性。计算得到的MSi/Ge的结构参数和形成焓与实验结果以及其他理论计算结果相吻合,结果表明MSi/Ge具有热力学稳定性且易于合成。计算得到了MX型合金化合物的弹性常数、体积模量、剪切模量、杨氏模量、弹性各向同性指标以及泊松比。基于弹性常数,得到了CoSi/Ge和RhSi/Ge的德拜温度-压强曲线。基于计算硬度的半经验模型,计算了该系列物质的硬度。其中,RhSi、FeGe和CoGe具有较高的弹性模量和较低的泊松比,具有成为超硬材料的潜质。 相似文献
7.
Isothermal fatigue (IF) tests were performed on H13 tool steel subjected to three different mechanical strain amplitudes at a constant temperature to determine the effects of mechanical strain amplitude on the microstructure of the steel samples. The samples' extent of damage after IF tests was compared by observation of their cracks and calculation of their damage parameters. Optical microscopy (OM) and scanning electron microscopy (SEM) were used to observe the microstructure of the samples. Cracks were observed to initiate at the surface because the strains and stresses there were the largest during thermal cycling. Mechanical strain accelerated the damage and softening of the steel. A larger mechanical strain caused greater deformation of the steel, which made the precipitated carbides easier to gather and grow along the deformation direction, possibly resulting in softening of the material or the initiation of cracks. 相似文献
8.
为了分析针状铁素体组织的形貌特点,进行了金相光学显微镜和扫描电子显微镜(SEM)观察.通过金相光学显微组织观察,发现了具有相同生长方向的针状铁素体组织和类似于在夹杂物形核的现象.通过SEM观察到不同晶界处形核的特点不同,在平直晶界处形核长大的针状铁素体组织比大曲率晶界处的组织更具规则性.测量出针状铁素体组织的维氏硬度约为377HV3.并指出维氏硬度值不能准确反映针状铁素体显微组织的本征硬度. 相似文献
9.
10.
Amorphous Al72Ni8Ti8Zr6Nb3Y3 powders were successfully fabricated by mechanical alloying. The microstructure, glass-forming ability, and crystallization behavior of amorphous Al72Ni8Ti8Zr6Nb3Y3 powders were investigated by X-ray diffraction (XRD), transmission electron microscopy (TEM), and differential scanning calorimetry (DSC). The isothermal crystallization kinetics was analyzed by the Johnson–Mehl–Avrami equation. In the results, the supercooled liquid region of the amorphous alloy is as high as 81 K, as determined by non-isothermal DSC curves. The activation energy for crystallization is as high as 312.6 kJ·mol?1 obtained by Kissinger and Ozawa analyses. The values of Avrami exponent (n) imply that the crystallization is dominated by interface-controlled three-dimensional growth in the early stage and the end stage and by diffusion-controlled two- or three-dimensional growth in the middle stage. In addition, the amorphous Al72Ni8Ti8Zr6Nb3Y3 powders were sintered under 2 GPa at temperatures of 673 K and 723 K. The results show that the Vickers hardness of the compacted powders is as high as Hv 1215. 相似文献