Dielectric relaxation and conduction mechanism in Aurivillius ceramic Bi5Ti3FeO15

For this study, we synthesized Aurivillius Bi5Ti3FeO15 ceramic using the generic solid-state reaction route and then performed room-temperature X-ray diffraction to confirm that the compound had a single phase with no impurities. The surface morphology of the prepared sample was observed to contain microstructural grains approximately 0.2–2 μm in size. The dielectric properties of the sample were determ-ined as a function of frequency in a range of approximately 100 Hz to 1 MHz at various temperatures (303 K ≤ T ≤ 773 K). Nyquist plots of the impedance data were found to exhibit a semi-circular arc in the high-temperature region, which is explained by the equivalent electrical circuit (R1C1)(R2QC2), where R1 and R2 represent the resistances associated with the grains and grain boundaries, respectively, C1 and C2 are the re-spective capacitances, and Q is the constant phase element (CPE), which accounts for non-Debye type of behavior. Our results indicate that both the resistance and capacitance of the grain boundaries are more prominent than those of the grains. The alternating current (ac) conductiv-ity data were analyzed based on the Jonscher universal power law, which indicated that the conduction process is dominated by the hopping mechanism. The calculated activation energies of the relaxation and conduction processes were very similar (0.32 to 0.53 eV), from which we conclude that the same type of charge carriers are involved in both processes.     

氟掺杂氧化锡薄膜电活性缺陷密度的太赫兹谱探测

从理论上分析了电场应力前后氟掺杂氧化锡（FTO）薄膜的能带结构和传导机理，提取了应力前后FTO薄膜的太赫兹电导率。采用Drude模型对应力前的FTO薄膜太赫兹（THz）电导进行了仿真；采用了Hopping模型对应力后的THz电导进行了仿真，实验与仿真结果一致。结果表明，应力后FTO的电导率提高了3个数量级，源于电场作用下的粒子内作用电导和粒子间作用（陷阱辅助隧穿）电导。通过适合的电导仿真模型，可以清楚地区分出陷阱辅助隧穿电导，从而提取FTO薄膜的陷阱密度。研究结果为利用太赫兹光谱提取半导体薄膜缺陷密度提供了一种便捷的新方法。     

Predicting Initial Formation Temperature for Deep Well Engineering with a New Method

With the progress of science and technology, human beings explore the energy under-ground with thousands of meters. As a thermophysical parameter, initial formation temperature (IFT) plays an essential...     

Acyl-chloride functionalized graphene oxide chemically grafted with hindered phenol and its application in anti-degradation of polypropylene

In this study,graphene oxide (GO) nanosheets were first functionalized by the acyl-chloride reaction and then reacted with hindered phenol (HP) to obtain HP grafted GO (GO-g-HP).The GO-g-HP prepared under the optimized condition exhibited a high efficiency against both thermal and photo oxidation of isotactic polypropylene (iPP).GO-g-HP exhibited a much better anti-aging efficiency than that of HP and GO used individually or that of their physical mixture.The outstanding anti-aging effect of GO-g-HP was attributed to the excellent synergistic effect produced between the chemically bonded GO and HP,which resulted in an improved oxygen barrier property of GO and excellent utilization of the free radical scavenging capability of GO and HP.Also,thanks to the grafting of HP on GO,the physical loss of HP,which was one of the main shortcomings for traditional small molecular antioxidants,was largely suppressed.It is expected that the GO-g-HP prepared can well meet the requirement of long-term applications of polymers in some harsh service conditions.     

基于正交设计的陶瓷再生混凝土配合比试验

为提高废旧陶瓷的再生利用率,将陶瓷颗粒与陶瓷粉作为再生混凝土骨料与掺合料进行再生利用.运用正交设计的试验方法,以陶瓷粉、陶瓷颗粒、再生细骨料、粉煤灰、硅灰为5因素,每个因素设置4个水平,共设计16组配合比方案,进行抗压、导热等试验,得到陶瓷再生混凝土的强度、导热系数等物理力学参数,并寻找出最优配合比.试验结果表明最佳配合比为:陶瓷粉的质量分数为10%,陶瓷颗粒的质量分数为20%,再生细骨料的质量分数为40%,粉煤灰的质量分数为15%,硅灰的质量分数为5%.     

“Fe（OH）3溶胶的制备及电泳”实验的探讨

探讨溶胶浓度、溶胶电导率、非电解质脲素加入量对Fe(OH)3溶胶ζ电位的影响,为"Fe(OH)3溶胶制备及电泳"实验提供参考。     

烧结温度对高速压制制备弥散强化铜材料导电率的影响

弥散强化铜材料具有高强度和高导电性的特性,孔洞是影响导电率的重要因素.本文采用高速压制成形技术,对Al2 O3质量分数为0.9%的弥散强化铜粉压制成形,研究了压制速度对生坯的影响.当压制速度为9.4 m·s-1时得到密度为8.46 g·cm-3的生坯.研究了烧结温度对烧结所得Al2 O3弥散强化铜试样导电率的影响.当生坯密度相同时,烧结温度越高,所得试样的导电率也越高.断口与金相分析表明：烧结温度为950℃时,烧结不充分,颗粒边界以及孔洞多而明显,孔洞形状不规则;烧结温度为1080℃时,颗粒边界消失,孔洞圆化,韧窝出现,烧结坯的电导率为71.3%IACS.     

Improving thermal insulation of TC4 using YSZ-based coating and SiO2 aerogel

In this paper, air plasmas spray(APS) was used to prepare YSZ and Sc2O3–YSZ(Sc YSZ) coating in order to improve the thermal insulation ability of TC4 alloy. Si O2 aerogel was also synthesized and affixed on TC4 titanium alloy to inhabit thermal flow. The microstructures, phase compositions and thermal insulation performance of three coatings were analyzed in detail. The results of thermal diffusivity test by a laser flash method showed that the thermal diffusivities of YSZ, Sc2O3–YSZ and Si O2 aerogel are 0.553, 0.539 and 0.2097 10 6m2/s, respectively. Then,the thermal insulation performances of three kinds of coating were investigated from 20 1C to 400 1C using high infrared radiation heat flux technology. The experimental results indicated that the corresponding temperature difference between the top TC4 alloy(400 1C) and the bottom surface of YSZ is 41.5 1C for 0.6 mm thickness coating. For 1 mm thickness coating, the corresponding temperature difference between the top TC4 alloys(400 1C) and the bottom surface of YSZ, Sc YSZ, Si O2 aerogel three specimens is 54, 54.6 and 208 1C, respectively. The coating thickness and species were found to influence the heat insulation ability. In these materials, YSZ and Sc YSZ exhibited a little difference for heat insulation behavior. However, Si O2 aerogel was the best one among them and it can be taken as protection material on TC4 alloys. In outer space,Si O2 aerogel can meet the need of thermal insulation of TC4 of high-speed aircraft.     

Influence of thermal-decomposition temperatures on structures and properties of V2O5 as cathode materials for lithium ion battery

Submicron spherical V2O5 particles with a uniform size and a lower crystallinity were successfully synthesized by a chemical precipitationthermal decomposition technique using the commercial V2O5 powders as starting material. The crystal structure and grain morphology of samples were characterized by X-ray diffraction(XRD) and scanning electron microscopy(SEM), respectively. Electrochemical testing such as discharge–charge cycling(CD) and cyclic voltammetry(CV) were employed in evaluating their electrochemical properties as cathode materials for lithium ion battery. Results reveal that the crystallinity and crystalline size of V2O5 particles increased when the thermal-decomposition temperature increased from 400 ℃ to 500 ℃, and their adhesiveness was also synchronously increased. This indicate that the thermaldecomposition temperature palyed a significant influence on electrochemical properties of V2O5 cathodes. The V2O5 sample obtained at 400 ℃ delivered not only a high initial discharge capacity of 330 m A h g-1and also the good cycle stability during 50 cycles due to its higher values ofα in crystal structure and better dispersity in grain morphology.     

高温高压碳酸盐岩地层酸蚀裂缝长期导流能力实验研究

酸蚀裂缝导流能力是评价酸化压裂效果的重要因素;而酸蚀裂缝在高闭合压力下闭合严重,导流能力很低,并且短期导流能力并不能代表生产时的导流能力,所以需要进行裂缝长期导流能力研究。结合托甫台奥陶系高温高压碳酸盐岩油藏的特征,运用高温高压酸化流动仪、FCES—100裂缝导流仪,进行了酸蚀裂缝、加砂水力裂缝、加砂酸蚀裂缝长期导流能力实验,考察了不同闭合压力下三种裂缝的长期导流能力的变化规律。实验所用酸液类型、酸岩接触时间、支撑剂尺寸和铺砂浓度都是通过前期实验优选得到,分别为稠化酸、60 min、40/70目陶粒及3.0 kg/m2。对实验数据进行分析对比,发现在高闭合压力下酸蚀加砂裂缝比酸蚀裂缝导流能力高,水力加砂裂缝比酸蚀加砂裂缝略高。