一类多孔介质型扩散互惠模型的共存态和渐近性

研究了一类具有多孔介质型扩散的3种群互惠模型Dirichlet边值问题.在适当的条件下,证明了该时变问题存在唯一有界整体解,且除了平凡解和半平凡解之外,相应的平衡态问题还存在正的最大解和最小解.此外,该时变解在一些初值函数下收敛到最大平衡解,而在另一些初值函数下收敛到最小平衡解.这种收敛性对反应函数的任意系数都成立.该结果意味着带多孔介质型扩散的互惠模型的动力学性态不同于带常数扩散项的.     

电化学合成重铬酸钾阳极的制备和电催化性能

针对电化学合成重铬酸钾绿色新技术,采用涂层自组装方法制备了钛基铱氧化物中间层钌铱钛氧化物复合电极(Ti/IrO_2/RuO_2-IrO_2-TiO_2).利用扫描电镜、X射线衍射分析了电极的微观结构和表面形貌,并采用循环伏安法研究了电极的电催化性能.结果表明,电极表面RuO_2-IrO_2-TiO_2柱状结晶规则均匀,并有明显空隙.电极在阳极液中析氧过电位较低,并具有稳定的较高的电催化活性.     

Tussah Silk Fibroin Porous Scaffolds Prepared with a Mild Self-assembly Process for Controlled Drug Release

Besides excellent biodegradability and biocompatibility,a useful tissue engineering scaffold should provide favorable surface properties,outstanding mechanical strength and controlled drug release property. In this paper,a mild process to prepare porous tussah silk fibroin（ TSF） scaffolds from aqueous solution was described. The n-butanol was used to control the self-assembly of tussah silk. The scaffolds with different TSF concentrations and the same volume showed differences in pore size and distribution. The maximum porosity of the poprepared porous scaffolds was 80% in this paper. And the pore size of the prepared porous scaffolds with different concentrations was between 10μm and 230 μm. X-ray diffraction（ XRD） analysis revealed that amorphous TSF was crystallized to β-sheet secondary structure upon gelatin. The TSF scaffolds for controlled drug release was studied and the result showed that the time of drug release was significantly longer. The produced TSF scaffolds with sustained drug release have potential application in tissue engineering.     

Electrorheological effect of Ti-bearing blast furnace slag with different TiC contents at 1500℃

The electrorheological properties of CaO–SiO2–Al2O3–MgO–TiO2–TiC slags were investigated to enhance understanding of the effect of TiC addition on the viscosity, yield stress, and fluid pattern of Ti-bearing slags in a direct-current electric field. The viscosities and shear stresses of 4wt% and 8wt% TiC slags were found to increase substantially with increasing electric field intensity, whereas virtually no rheological changes were observed in the 0wt% TiC slag. The Herschel–Bulkley model was applied to demonstrate that the fluid pattern of the 4wt% TiC slag was converted from that of a Newtonian fluid to that of a Bingham fluid in response to the applied electric field; and the static yield stress increased linearly with the square of the electric field intensity.     

核电站凝汽器用钛焊管蒸汽腐蚀疲劳性能研究

测定了国产和进口核电站凝汽器用钛焊管在室温大气和人工海水100 ℃水蒸汽介质中的疲劳性能，同时采用扫描电子显微镜对疲劳断口进行了观察，探讨了钛焊管的蒸汽腐蚀疲劳机理。研究结果表明：国产钛焊管与进口钛焊管的疲劳寿命较为接近，水蒸汽氛围大幅度降低了钛焊管的疲劳寿命；疲劳试样的裂纹均萌生于钛焊管焊缝区域的外表面，多为多源萌生，裂纹扩展均以条纹机理为主；断口处有少量二次裂纹，未发现沿晶断裂及周期解理断裂特征，静断区断口形貌为韧窝；从蒸汽腐蚀疲劳试样中，未能观察到明显的腐蚀产物；钛焊管的蒸汽疲劳腐蚀是交变应力和电化学腐蚀交互作用的结果。     

阳极氧化铝模板高有序孔的形成机理综述

阳极氧化铝模板法是合成纳米阵列材料的最常用的方法,然而有关氧化铝纳米孔的形成机理却没有达到统一的认识.利用26篇文献综述了氧化铝膜的理想结构和电场辅助的溶解模型、体积膨胀的应力模型、稳态孔的生长模型、临界电流的密度模型和梅花结构模型等5种不同的氧化铝纳米孔形成机理,最后对氧化铝模板的应用和发展前景提出了展望.     

高钛球团焙烧行为及其强化技术

研究了高钛球团的焙烧特征和固结行为.随着TiO2含量的增加,球团焙烧难度增大,当TiO2质量分数由10%增加至21%时,高钛球团所需预热时间由12 min延长至26 min以上,焙烧球强度由每个2486 N降低至每个1728 N.高钛球团由于FeTiO3含量高,导致氧化速度慢、预热球氧化程度低,不利于焙烧固结时钛赤铁矿固溶体晶粒的长大,使得球团固结强度差.通过添加NaOH结合润磨工艺增大颗粒表面能和反应活性,促进了固相扩散,并生成少量低熔点化合物,有利于再结晶过程的扩散迁移,使Ti富集在Fe2 TiO5中并促进钛赤铁矿晶粒长大,强化了高钛球团焙烧固结,可使预热时间缩短至16 min,球团强度提高至每个2141 N.     

Transient pressure analysis for the reactor core and containment of a HTGR after a primary loop pressure boundary break accident

The pressure variances in the reactor core and containment of a High Temperature Gas-cooled Reactor (HTGR) after a primary loop pressure boundary break accident determine the structural integrity and safety of the reactor. Based on mass conservation, energy conservation and state equations, explicit formulae for the transient pressure and temperature variances in the pressure vessels were deduced, and a set of differential equations for the transient pressure and temperature variances in the containment were developed. Numerical simulation was also conducted to investigate the transient pressure and temperature variances in the pressure vessels and containment. The results show that energy transformation due to expansion work cannot be neglected. The maximum pressure in the containment could increase by 40 percent due to blockage caused by air in the containment. Detailed numerical simulations of the transient pressure and temperature variance in the reactor core flow passages were also conducted. The results show that the pressures acting on the reactor core and containment are below acceptable values.     

Fabrication of an r-Al2Ti intermetallic matrix composite reinforced with α-Al2O3 ceramic by discontinuous mechanical milling for thermite reaction

In this study, a powder mixture with an Al/TiO2 molar ratio of 10/3 was used to form an r-Al2Ti intermetallic matrix composite (IMC) reinforced withα-Al2O3 ceramic by a novel milling technique, called ...     

硫酸钛为钛源制备二氧化钛的实验条件研究

实验以硫酸钛为钛源、尿素为沉淀剂、聚乙二醇600为分散剂,采用均匀沉淀法制备二氧化钛粉末。主要讨论了影响沉淀形成时间的主要因素:尿素的用量及加入方法、聚乙二醇的用量、以及水浴的温度等。实验结果表明,以硫酸钛为钛源、尿素为沉淀剂、聚乙二醇600为分散剂,采用均匀沉淀法制备二氧化钛粉末最佳反应条件为:在水浴加热343 K条件下,将尿素缓慢滴加到硫酸钛和聚乙二醇600的混合液中,硫酸钛和聚乙二醇600的混合液在磁力搅拌器搅拌时滴加尿素,用硫酸调节pH在1.5~2,保持硫酸钛、尿素和聚乙二醇600的摩尔比1∶12∶0.01。