Research and Trial Production of X80 Pipeline Steel with High Toughness Using Acicular Ferrite

Keywords:pipelinesteel;X80;acicularferrite;coil1Introduction Itisaneconomicalwaytotransportoilandgasthrough longdistancebyusingpipelinewithhighpressureandlarge diameter.Inthiscase,isusuallyrequiredthehigh grade,highperformancepipelinesteeltoguaranteeasafeand reliableserviceatsuchhighpressure,aswellastoreduce thecostofconstructionandoperationforapipelineproject.NowX70pipelinesteelhasbecomethemostusedsteelgrade inlongdistancepipelineprojectsovertheworld.SomeX80pipelinetrialprojectshavebeencons…     

对配电网中性点接地方式的分析和选择

对中压配电网中采用的各种中性点接地方式进行了技术分析比较,并就城乡配电网改造中的中性点接地方式的选择进行了简单的探讨。     

用于非圆截面车削的动圈电机伺服刀架系统的设计

设计了一种新型的由动圈直线电机驱动可用于可凸变椭圆活塞车削的伺服刀架系统，给出了新型刀架机械系统的数学模型及其闭合控制系统的组成，分析了动圈中温升较高的原因，提出了降低动圈铜损、限制温升的措施。     

螺旋管簧的可靠性鲁棒设计

在可靠性优化设计理论与可靠性灵敏度分析方法的基础上，讨论了螺旋管簧的可靠性鲁棒设计问题，提出了可靠性鲁棒设计的数值计算方法，把可靠性灵敏度溶入可靠性优化设计模型之中，将可靠性鲁棒设计归结为满足可靠性要求的多目标优化问题。     

停车场智能管理系统

为解决传统的停车场人工管理在停车效率、安全、性能及管理上的不足，应用集散控制原理设计了停车场智能管理系统，并进一步研究了如何针对不同场所的停车场设计相应的自动识别装置、入口处读卡与发卡装置及通道管理装置等．该智能管理系统也可用于公路收费站．     

板坯电磁制动器的设计

阐述了电磁制动的原理,设计了电磁制动的基本结构,冷却系统以及装配方案.改进了线圈的结构设计,增强了电磁制动效果和节约了电能的消耗.对板坯电磁制动与冶金效果的关系进行了研究.结果表明,在恒稳电磁场作用下,钢液内形成的与钢液流动相反的电磁力可有效地控制钢液流动,稳定液面波动,有利于夹杂物的去除,减少气隙,改善板坯钢材的结晶组织的形成,提高板坯的质量.     

自身磁场对载流线圈受力的影响

本文讨论了载流线圈在外磁场中受力与自身磁场无关。阐明了普物为什么不谈自身场的原因。     

交流电阻焊动态功率因数的实时解析算法

基于对交流电阻焊焊接变压器初级回路电压、电流信号的建模分析,提出电流过零导数比法测量电阻焊动态功率因数.采用微型Rogowski线圈直接检测电流过零导数,并在以DSP为核心的点焊质量实时监控系统中实现了动态功率因数的实时计算.电流导数信号实时检测技术和数学模型的简洁解析表达形式同时保证了该算法良好的实时性.试验结果证明,该算法是有效的.     

Simulation of g factor for size optimization and coupling in phased array coil design

The effect of geometric parameters of the coil element in an array on signal-to-noise ratio (SNR) and g factor of parallel imaging are analyzed, and the optimal parameters for the maximal SNR and minimal g factor are also given in this paper. In addition, the effects of coupling on SNR and g factor have been analyzed. The test results indicate that g factor for parallel imaging is greatly increased and SNR is decreased for coupling. According to the optimization, a six-channel parallel coil has been designed for torso imaging.     

A new simulated annealing method of designing NMR biplanar shim coils

A new SA (simulated annealing) method is presented for the design of longitudinal shim coils for NMR (nuclear magnetic resonance) equipment. First, AGL (adaptive Gauss-Lobatto) quadrature used by the traditional SA method is analyzed. Two kinds of complete elliptic integrals are introduced to integrate the spatial magnetic field, which increases the computing speed by 13.3 times. Then, the system energy calculation is extended to the field of the z-axis. The results illustrate that the coil-set efficiency designed by the new SA method is 15% higher than that of the traditional one, and the field inhomogeneity is reduced from 1.20% to 0.49%. Finally, a prototype of coil assembly for NMR rock-core analyzer is built, and the experimental results are in good agreement with the theoretically calculated results.