烧结铁矿中FeO含量对其在富氢高炉中还原行为的影响

Japan started the national project “COURSE 50” for CO₂ reduction in the 2000s. This project aimed to establish novel technologies to reduce CO₂ emissions with partially utilization of hydrogen in blast furnace-based ironmaking by 30% by around 2030 and use it for practical applications by 2050. The idea is that instead of coke, hydrogen is used as the reducing agent, leading to lower fossil fuel consumption in the process. It has been reported that the reduction behavior of hematite, magnetite, calcium ferrite, and slag in the sinter is different, and it is also considerably influenced by the sinter morphology. This study aimed to investigate the reduction behavior of sinters in hydrogen enriched blast furnace with different mineral morphologies in CO–CO₂–H₂ mixed gas. As an experimental sample, two sinter samples with significantly different hematite and magnetite ratios were prepared to compare their reduction behaviors. The reduction of wustite to iron was carried out at 1000, 900, and 800°C in a CO–CO₂–H₂ atmosphere for the mineral morphology-controlled sinter, and the following findings were obtained. The reduction rate of smaller amount of FeO led to faster increase of the reduction rate curve at the initial stage of reduction. Macro-observations of reduced samples showed that the reaction proceeded from the outer periphery of the sample toward the inside, and a reaction interface was observed where reduced iron and wustite coexisted. Micro-observations revealed three layers, namely, wustite single phase in the center zone of the sample, iron single phase in the outer periphery zone of the sample, and iron oxide-derived wustite FeO and iron, or calcium ferrite-derived wustite 'FeO' and iron in the reaction interface zone. A two-interface unreacted core model was successfully applied for the kinetic analysis of the reduction reaction, and obtained temperature dependent expressions of the chemical reaction coefficients from each mineral phases.     

Mg和La对Ca–Ti 处理钢中夹杂物演变和组织的影响

The evolution of inclusions and the formation of acicular ferrite (AF) in Ca–Ti treated steel was systematically investigated after Mg and La addition. The inclusions in the molten steel were Ca–Al–O, Ca–Al–Mg–O, and La–Mg–Ca–Al–O after Ca, Mg, and La addition, respectively. The type of oxide inclusion in the final quenched samples was the same as that in the molten steel. However, unlike those in molten steel, the inclusions were Ca–Al–Ti–O + MnS, Ca–Mg–Al–Ti–O + MnS, and La–Ca–Mg–Al–Ti–O + MnS in Mg-free, Mg-containing, and La-containing samples, respectively. The inclusions distributed dispersedly in the La-containing sample. In addition, the average size of the inclusions in the La-containing sample was the smallest, while the number density of inclusions was the highest. The size of effective inclusions (nucleus of AF formation) was mainly in the range of 1–3 μm. In addition, the content of ferrite side plates (FSP) decreased, while the percentage of AF increased by 16.2% due to the increase in the number of effective inclusions in the La-containing sample in this study.     

摩擦焊接碳钢（EN24）和镍基高温合金（IN718）的显微组织和力学性能

Continuous-drive rotary friction welding was performed to join cylindrical specimens of carbon steel (EN24) and nickel-based superalloy (IN718), and the microstructures of three distinct weld zones—the weld interface (WI)/thermo-mechanically affected zone (TMAZ), the heat-affected zone (HAZ), and the base metal—were examined. The joint was observed to be free of defects but featured uneven flash formation. Electron backscatter diffraction (EBSD) analysis showed substantial changes in high-angle grain boundaries, low-angle grain boundaries, and twin boundaries in the TMAZ and HAZ. Moreover, significant refinement in grain size (2–5 μm) was observed at the WI/TMAZ with reference to the base metal. The possible causes of these are discussed. The microhardness profile across the welded joint shows variation in hardness. The changes in hardness are ascribed to grain refinement, phase transformation, and the dissolution of strengthening precipitates. The tensile test results reveal that a joint efficiency of 100% can be achieved using this method.     

人工闪锌矿氧压酸浸过程中Cu2+的催化机理研究

The potential autoclave was used to study the catalytic mechanism of Cu2+ during the oxygen pressure leaching process of artificial sphalerite. By studying the potential change of the system at different temperatures and the SEM–EDS difference of the leaching residues, it was found that in the temperature range of 363–423 K, the internal Cu2+ formed a CuS deposit on the surface of sphalerite, which hindered the leaching reaction, resulting in a zinc leaching rate of only 51.04%. When the temperature exceeds 463 K, the system potential increases steadily. The increase in temperature leads to the dissolution of the CuS, which is beneficial to the circulation catalysis of Cu2+. At this time, the leaching rate of Zn exceeds 95%. In addition, the leaching kinetics equations at 363–423 and 423–483 K were established. The activation energy of zinc leaching at 363–423 and 423–483 K is 38.66 and 36.25 kJ/mol, respectively, and the leaching process is controlled by surface chemical reactions.     

汽车暴露面板带有表面条状缺陷的夹杂物分布特征分析:一种定量电解方法

The specific distribution characteristics of inclusions along with the sliver defect were analyzed in detail to explain the formation mechanism of the sliver defect on the automobile exposed panel surface. A quantitative electrolysis method was used to compare and evaluate the three-dimensional morphology, size, composition, quantity, and distribution of inclusions in the defect and non-defect zone of automobile exposed panel. The Al₂O₃ inclusions were observed to be aggregated or chain-like shape along with the sliver defect of about 3–10 μm. The aggregation sections of the Al₂O₃ inclusions are distributed discretely along the rolling direction, with a spacing of 3–7 mm, a length of 6–7 mm, and a width of about 3 mm. The inclusion area part is 0.04%–0.16% with an average value of 0.08%, the inclusion number density is 40 mm?2 and the inclusion average spacing is 25.13 μm. The inclusion spacing is approximately 40–160 μm, with an average value of 68.76 μm in chain-like inclusion parts. The average area fraction and number density of inclusions in the non-defect region were reduced to about 0.002% and 1–2 mm?2, respectively, with the inclusion spacing of 400 μm and the size of Al₂O₃ being 1–3 μm.     

超声振动辅助钨极惰性气体焊接异种金属 316L 和 L415

Ultrasonic vibration assisted tungsten inert gas welding was applied to joining stainless steel 316L and low alloy high strength steel L415. The effect of ultrasonic vibration on the microstructure and mechanical properties of a dissimilar metal welded joint of 316L and L415 was systematically investigated. The microstructures of both heat affected zones of L415 and weld metal were substantially refined, and the clusters of δ ferrite in traditional tungsten inert gas (TIG) weld were changed to a dispersive distribution via the ultrasonic vibration. The ultrasonic vibration promoted the uniform distribution of elements and decreased the micro-segregation tendency in the weld. With the application of ultrasonic vibration, the average tensile strength and elongation of the joint was improved from 613 to 650 MPa and from 16.15% to 31.54%, respectively. The content of Σ3 grain boundaries around the fusion line zone is higher and the distribution is more uniform in the ultrasonic vibration assisted welded joint compared with the traditional one, indicating an excellent weld metal crack resistance.     

在酸性溶液中加压氧化三价砷离子和二价铁离子

The co-oxidation of As(III) and Fe(II) in acidic solutions by pressured oxygen was studied under an oxygen pressure between 0.5 and 2.0 MPa at a temperature of 150°C. It was confirmed that without Fe(II) ions, As(III) ions in the solutions are virtually non-oxidizable by pressured oxygen even at a temperature as high as 200°C and an oxygen pressure up to 2.0 MPa. Fe(II) ions in the solutions did have a catalysis effect on the oxidation of As(III), possibly attributable to the production of such strong oxidants as hydroxyl free radicals (OH·) and Fe(IV) in the oxidation process of Fe(II). The effects of such factors as the initial molar ratio of Fe(II)/As(III), initial pH value of the solution, oxygen pressure, and the addition of radical scavengers on the oxidation efficiencies of As(III) and Fe(II) were studied. It was found that the oxidation of As(III) was limited in the co-oxidation process due to the accumulation of the As(III) oxidation product, As(V), in the solutions.     

采用超声组装与滚压工艺制备铝–碳纳米管复合材料

This study introduced a novel fabrication of aluminum–carbon nanotube (CNT) composites by employing bulk acoustic waves and accumulative roll bonding (ARB). In this method, CNT particles were aligned using ultrasonic standing wave in an aqueous media, and the arrayed particles were precipitated on the aluminum plate substrate. Then, the plates rolled on each other through the ARB process with four passes. Optical and scanning electron micrographs demonstrated the effective aligning of CNTs on the aluminum substrate with a negligible deviation of arrayed CNTs through the ARB process. The X-ray diffraction pattern of the developed composites showed no peaks for carbon and aluminum carbide. In addition, tensile tests showed that the longitudinal strength of the specimens processed with aligned CNTs was significantly greater than that of the specimens with common randomly dispersed particles. The proposed technique is beneficial for the fabrication of Al–CNT composites with directional mechanical strength.     

海南岛地体及其毗邻陆缘晚中生代—新生代古地磁研究和构造演化

本文叙述了对海南岛及其毗邻大陆边缘白垩纪到第四纪地层岩石进行古地磁研究的全部工作过程。通过分析岩石中剩余磁矢量的磁偏角及磁倾角的变化,提出海南岛白垩纪以来经历的构造演化模式如下:早期伴随顺时针旋转而向南迁移,后期伴随逆时针转动并向北运移。联系该地区及邻区的地质、地球物理资料,对海南岛上述的构造地体运动提出以下认识:北部湾内早期有一拉张作用,主要是该作用使湾内地壳显著伸长减薄,形成北部湾盆地。从而导致了海南岛的早期构造运动,而海南岛后期的构造运动则主要是受南海海底扩张的影响。海南地体运动规律的阐明对于了解北部湾油气盆地的形成演化有重要的理论和实际意义。     

Characterization of Ordovician carbonate reservoirs, southeastern Saskatchewan, Canada

The discovery of the prolific Ordovician Red River reservoirs in 1995 in southeastern Saskatchewan was the catalyst for extensive exploration activity which resulted in the discovery of more than 15 new Red River pools. The best yields of Red River production to date have been from dolomite reservoirs. Understanding the processes of dolomitization is, therefore, crucial for the prediction of the connectivity, spatial distribution and heterogeneity of dolomite reservoirs.The Red River reservoirs in the Midale area consist of 3～4 thin dolomitized zones, with a total thickness of about 20 m, which occur at the top of the Yeoman Formation. Two types of replacement dolomite were recognized in the Red River reservoir: dolomitized burrow infills and dolomitized host matrix. The spatial distribution of dolomite suggests that burrowing organisms played an important role in facilitating the fluid flow in the backfilled sediments. This resulted in penecontemporaneous dolomitization of burrow infills by normal seawater. The dolomite in the host matrix is interpreted as having occurred at shallow burial by evaporitic seawater during precipitation of Lake Almar anhydrite that immediately overlies the Yeoman Formation. However, the low δ18O values of dolomited burrow infills (-5.9‰～ -7.8‰, PDB) and matrix dolomites (-6.6‰～ -8.1‰, avg. -7.4‰ PDB) compared to the estimated values for the late Ordovician marine dolomite could be attributed to modification and alteration of dolomite at higher temperatures during deeper burial, which could also be responsible for its 87Sr/86Sr ratios (0.7084～0.7088) that are higher than suggested for the late Ordovician seawaters (0.7078～0.7080). The trace amounts of saddle dolomite cement in the Red River carbonates are probably related to "cannibalization" of earlier replacement dolomite during the chemical compaction.     

试论如何为计算机系统提速

1　问题的提出计算机自诞生之日起 ,就以其快速、高效而深受人们的青睐 ,如今更是迅速普及至世界范围各行各业 ,我国的个人计算机占有率直线上升 .挑战极限的ＣＰＵ、内存、加速卡等硬件设施 ,使人们驰聘于“高速”的信息快车道上 .可由于计算机更新换代的速度很快 ,人们买回家的计算机转眼间就失去了速度的优势 .受各种因素影响 ,人们不可能随时更换自己的计算机 ,但我们完全可以通过自身的努力 ,通过系统的软设置为自己的计算机提速 .众所周知 ,计算机是由软件和硬件配合进行工作的 ,在硬件规格已经确定的情况下往往可以通过特定的软件对…     

普通话朗读中的停延

学习普通话的重要环节是在语流中模仿普通话的节律。停延作为节律的基础,确定了语流中的音步组合,进而关系到协同发音、连续变调等一系列语音现泉。停延的研究对于普通话的朗读教学具有重要的现实意义。该文以《普通话水平测试实施纲要》提供的60篇短文为语料,对于文中的停顿做出了定量、定性的分析：普通话的音步组合层的平均长度为5—7个音节,影响各篇短文音步组合层长度的主要因素是文体风格。该文根据60篇短文的语音资料,提出了设置句中无标点停顿的语义原则、语法原则、语用原则。根据语义原则,只能在有助于语义表达的地方停顿。根据语法原则,只能在构成语法结构的地方停顿。如果在某种情况下构成了非语法停顿,那是为了满足节律的需要。根据语用原则,人们通过对语境的分析,以停顿为手段,实现表情达意的最佳效果和节奏的匀称感。文中以大量例句,对各种语法结构中的语音停顿现泉进行比较说明,做出了令人信服的阐释。     

《麦克白》语言的诗性特征

莎士比亚不仅有独到的社会观察力和剖析力，而且还有强大的艺术构建力。在悲剧《麦克白》中，莎翁以诗人的激情和想象，用确切的措辞、优奏的诗句以及生动的意象为我们营造了一个奇特的世赛。本文通过对《麦克白》语言的诗性特征分析，从音韵、比喻、意象、对照以及用典上向读者展示此剧的精妙和震撼。     

基于组合充电法的蓄电池激活硬件电路研究

基于一种新的组合充电法（正脉冲恒流充电、负脉冲去极化、PWM均衡放电）,研究蓄电池修复仪控制系统的硬件结构和软件设计的思想。通过系统调试,对大量数据的分析及对参数的不断调整,排除干扰因素,实现了对蓄电池不同充放电工作方式的控制,并获得了比较满意的修复效果。     

建构中国古代文学审美理论:动因和方法

从提高“”的审美能力、“史”的认知能力、“论”的理解能力等方面阐述了建构中国古代学审美理论体系的动因，从注重古人创作和审美的实际、用今人的观点来透视、把定向观照和多向思维结合起来等方面探讨了建构这种理论的方法。目的在于使中国古代学理论的研究既有传统性又有现代性，既有本土性又有世界性。     

重氮氨基类试剂的合成其及分析应用

本文对已报道过的重氮氨基类试剂分类进行了综述;介绍了这类试剂的合成及纯化方法;列举了几个应用广泛的试剂和一些新试剂的典型分光光度分析的应用实例。初步讨论了络合物的组成、结构,以及取代基对试剂灵敏度的影响。提出了值得重视的研究内容。     

试论二胡演奏的呼吸规律及运用

本主要对呼吸的几种规律及运用进行初步探讨，并对二胡演奏时呼吸存在哪些内在联系，它对表达乐曲的思想感情是否存在直接或间接的影响；在二胡演奏过程中，如何将呼吸的运用与演奏配合默契，使二胡演奏达到较好的表现效果，进行了一些初步的探索。     

两种干燥方式对土壤中多环芳烃回收率及同分异构体比值的影响

通过实验室模拟向泥炭土和农田土添加不同量的外源多环芳烃单体标准物质,  经冷冻干燥和自然风干处理后,  用气相色谱-质谱法（GC-MS）对土壤中16种外源多环芳烃单体进行测定,  分析两种干燥方式对土壤外源多环芳烃回收率和同分异构体比值的影响,  以反映不同干燥方式下土壤中多环芳烃测定的准确度及自然土壤多环芳烃来源判定的差异. 实验结果表明：  泥炭土随外源多环芳烃添加量的增加,  多环芳烃总量回收率呈先降低后增加的趋势,  在相同添加量下， 风干处理的多环芳烃总量回收率（56.29%~80.15%）均高于冻干处理的回收率（52.82%~78.31%）,  泥炭土单体多环芳烃低环组分风干处理高于冻干处理的回收率,  高环组分冻干处理高于风干处理的回收率;  不同干燥方式处理下农田土中多环芳烃总量回收率差异显著（P<0.05）,  经冻干处理后的总量回收率为64.40%~73.81%,  经风干处理后的总量回收率为40.88%~57.01%,  其单体多环芳烃冻干处理均高于风干处理的回收率； 两种土壤的有机质质量比和含水率不同可能是导致多环芳烃总量和单体回收率差异的主要因素；  在两种干燥方式处理下,  泥炭土中不同多环芳烃同分异构体比值无显著差异,  农田土中多环芳烃同分异构体比值受干燥方式影响显著.