首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到18条相似文献,搜索用时 125 毫秒
1.
Mathematical Programming Solution for the Frictional Contact Muitipole BEM   总被引:1,自引:0,他引:1  
This paper presents a new mathematical model for the highly nonlinear problem of frictional contact. A programming model, multipole boundary element method (BEM), was developed for 3-D elastic contact with friction to replace the Monte Carlo method. A numerical example shows that the optimization programming model for the point-to-surface contact with friction and the fast optimization generalized minimal residual algorithm (GMRES(m)) significantly improve the analysis of such problems relative to the conventional BEM.  相似文献   

2.
A fast multipole boundary element method (FM-BEM) was applied for the analysis of microcracked solids. Both the computational complexity and memory requirement are reduced to O(N), where N is the number of degrees of freedom. The effective elastic moduli of a 2-D solid containing thousands of randomly distributed microcracks were evaluated using the FM-BEM. The results prove that both the differential method and the method proposed by Feng and Yu provide satisfactory estimates to such problems. The effect of a non-uniform distribution of microcracks has been studied using a novel model. The numerical results show that the non-uniform distribution induces a small increase in the global stiffness.  相似文献   

3.
Multipole BEM for 3-D Elasto-Plastic Contact with Friction   总被引:3,自引:0,他引:3  
The analysis of 3-D elasto-plastic contact with friction is a highly nonlinear problem. The elements in the contact and plastic zones should be refined to obtain accurate information about the real size,displacement, and traction in the contact zone. However, the increase in the number of degrees of freedom is limited when traditional boundary element method (BEM) is used with the larger memory size and long CPU time required for the solution procedure. This paper describes the additional mathematical friction model to the 3-D elastic multipole BEM to develop a 3-D elasto-plastic contact multipole BEM. Numerical tests show that with this new method, the needed computer memory size is only 2% of the traditional BEM model with friction, which erases large-scale computing with refined meshes and improves the computational accuracy.  相似文献   

4.
The fast multipole method (FMM) has been used to reduce the computing operations and memory requirements in large numerical analysis problems. In this paper, the FMM based on Taylor expansions is combined with the boundary element method (BEM) for three-dimensional elastostatic problems to solve thin plate and shell structures. The fast multipole boundary element method (FM-BEM)requires O(N) operations and memory for problems with N unknowns. The numerical results indicate that for the analysis of thin structures, the FM-BEM is much more efficient than the conventional BEM and the accuracy achieved is sufficient for engineering applications.  相似文献   

5.
6.
A 2-D cyclic variation of integrated backscatter (CVIB) imaging method was established for detecting myocardial ischemia. To demonstrate the feasibility and validity of this method, animal experiments were conducted. Acute myocardial ischemia was induced by occluding left anterior descending coronary artery in 10 anesthetized open-chest dogs. While scanning the normal hearts and the ischemic hearts with a B scanner, digital radiofrequency data were acquired by a real-time acquisition system in synchronism. The offline analysis to the radio-frequency signal with the 2-D CVIB imaging method was performed to verify the consistency between the imaging result and the design of the experiment. In addition, 4 dogs in experiment were treated with the heart pacemaker in order to investigate the influence of changing in heart rate on the detection of ischemic myocardium with the proposed method. The experimental result showed that the 2-D CVIB imaging method succeeded in detecting the ischemic myocardium and is a new non-invasive way for the cardiologists to both quantitatively and visually evaluate the contractile performance of the myocardium.  相似文献   

7.
A new wear-graphy technology was developed, which can simultaneously identify the shape and composition of wear debris, for both metals and non-metals. The fundamental principles of the wear-graphy system and its wear-gram system are discussed here. A method was developed to distribute wear debris on a slide uniformly to reduce overlapping of wear debris while smearing. The composition identification analyzes the wear debris using the scanning electron microscope (SEM) energy spectrum, infrared-thermal imaging and X-ray imaging technology. A wear debris analysis system based on database techniques is demonstrated, and a visible digitized wear-gram is acquired based on the information of wear debris with image collection and processing of the wear debris. The method gives the morphological characteristics of the wear debris, material composition identification of the wear debris, intelligent recognition of the wear debris,and storage and management of wear debris information.  相似文献   

8.
Fiber-reinforced composites are commonly used in various engineering applications. The mechanical properties of such composites depend strongly on micro-structural parameters. This paper presents a new boundary element method (BEM) for numerical analysis of the mechanical properties of 3-D fiber-reinforced composites. Acceleration of the BEM is achieved by means of a fast multipole method (FMM), in allowing large scale simulations of a finite elastic domain containing up to 100 elastic fibers to be performed on one personal computer. The maximum number of degrees of freedom can reach a value of over 250 000. The effects of several key micro-structural parameters on the local stress fields and on the effective elastic moduli of fiber-reinforced composites are evaluated. The numerical results are compared with analytical predictions and good agreement is observed. The results show that the fast multipole BEM could be a prom- ising tool for further understanding of the mechanical behavior of such composites.  相似文献   

9.
An analytical method has been developed to determine hisphenoi A and five degradation products of alkyiphenoi ethoxylates in sewage and sludge. The parameters of accelerated solvent extraction (ASE) were optimized. C18 cartridge was used to clean up the sewage and the extract of sludge. The sensitivity of the mass detector was improved by adjusting the voltage of the lens manually. The instrumental detection limit was 3.2-17.8pg. The method detection limits were 2.5-11.4 ng/L and 0.3-2.1ng/g for sewage and sludge analysis respectively. The recovery and relative standard deviation for sewage analysis were 79.2%-111.4% and 6.9% - 12.6%; for sludge analysis were 68.5% - 114.0% and 8.9%-16.0%. Finally this method was applied to determining the phenolic endocrine disrupting chemicals in sewage and sludge from a sewage treatment plant in Beijing.  相似文献   

10.
A new analysis method was developed to simulate the dynamic process of a frictional heatstress coupled field. The relationship between the frictional heat and the thermal stress was investigated for concave cylinder contact conditions. The results show that, as a nonlinear contact problem, the frictional heat at the contact areas changes with moving velocity in both value and distribution, and that the transient frictional heat at the dynamic condition has a peak within a cycle. The dynamic process of friction heat and thermal stresses affects diffusion of the frictional effects. The result can be helpful for dynamic simulation of diffusion lubrication of elements at elevated temperatures.  相似文献   

11.
快速多极边界元法在薄板结构中的应用   总被引:2,自引:0,他引:2  
基于Taylor级数多极展开研究了边界元快速多极算法(FM—BEM),并将它应用于薄板结构。算例分析表明FM—BEM的计算时间和存储空间明显少于常规边界元迭代解法。随着问题规模的增大,这种优势将更加突出。  相似文献   

12.
多层快速多极子分析三维复杂目标的谐振区电磁散射特性   总被引:1,自引:0,他引:1  
用多层快速多极子方法(MLFMA)和预优的广义最小残差法(GMRES)计算了三维复杂目标的谐振区电磁散射特性.对于在谐振区中5~10个波长目标的电磁散射体,MLMFA比矩量法(MOM)和快速多极子法(FMM)占用内存少很多,计算速度也更快;本文讨论了MLFMA中重要参数多极子数L的优化选取,同时采用了预优的GMRES方法求解MLFMA大规模矩阵方程,这比采用传统的共轭梯度(CG)法具有更大的优越性.最后对某导弹模型和典型隐身飞机模型进行了谐振区散射特性的高效求解分析.  相似文献   

13.
将快速多极算法和广义极小残值法(GMRES)结合于虚边界元法的方程求解,形成了快速多极虚边界元法的求解思想.本方法采用了"源点"多极展开和"场点"局部展开的组合处理方案,使得原问题方程组求解的计算耗时量和储存量均降至与所求问题的计算自由度数成线性比例.文中分析了含随机分布多圆孔板的有效弹性模量,并与其它数值方法的结果进行了比较,同时数值验证了本方法的可行性、计算精度及计算效率.  相似文献   

14.
Mathematical Programming Solution for the Frictional Contact Multipole BEM   总被引:4,自引:0,他引:4  
IntroductionElastic friction contact problems require accuratetracking of the movement of objects before and aftercontact and the interaction during contacts and correctsimulation of the frictional behavior between the con-tact surfaces. The boundary element method (BEM)[1,2]is well suited to accurately describe the variation of thefrictional contact conditions since the highly nonlineareffects only occur on the contact surface. For nonlinear frictional contact, various approacheshave been …  相似文献   

15.
将快速多极展开法(FMM)和广义极小残值法(GMRES)结合于三维位势问题的虚边界元最小二乘法,使求解方程的计算量和储存量与所求问题的计算自由度数成线性比例;欲达到数值模拟大规模自由度问题的目的.基于位势问题虚边界元最小二乘法的数值求解格式,将对角化和指数展开系数的概念引入到常规的快速多极展开法中,将三维位势问题的基本解推导为更适合于快速多极算法的展开格式,并用广义极小残值法求解方程组,旨在达到进一步提高效率且仍保证较高计算精度的目的.数值算例说明了该方法的可行性,及计算效率和计算精度.  相似文献   

16.
通过基本解的多极展开与边界元线性方程组的隐式求解方法(GMRES)相结合,开发出了快速多极边界元法。Taylor级数多极边界元法更新了传统边界元法的求解模式,大大提高了计算效率,扩大了边界元法的求解规模。介绍了Taylor级数多极边界元法的发展历史和现状,给出了Taylor级数多极边界元法的基本思想、基本原理和分类,给出了基本解的Taylor展开方法和边界积分的基本实现步骤。将该方法应用于轧制工程中,通过轧辊弹性变形和HC轧机辊系接触和变形的数值解析,说明了Taylor级数多极边界元法适合于大规模轧制工程  相似文献   

17.
为了求解开域电磁场问题,提出一种区域映射有限元方法。该方法把待求解的无限大区域划分为内部有限区域和外部无限区域。对内部区域,形成传统的有限元方程;对外部区域,引入几何中的Kelvin变换,对变换后的场域形成另一个有限元方程。内外区域的方程在公共边界上耦合。结果表明,该方法使用1/9甚至更少的单元即可达到传统有限元法的精度。与传统有限元法相比,该方法大量减少生成的网格单元数、计算所需的内存和时间。已在二维和三维开域问题计算中实现了该方法。  相似文献   

18.
三维快速多极边界元高性能并行计算   总被引:2,自引:0,他引:2  
该文实现了快速多极边界元法的一种高性能并行计算。其并行求解器基于自适应新版本快速多极边界元算法,采用三维二次等参元和等精度积分格式,并通过实测的任务量进行分布式并行环境下的合理负载划分。数值算例表明,该求解器在保持高次边界元高精度优点的基础上,对于几何形状不规则的结构仍能保持较好的并行效率,和传统边界元法相比使解题规模有了数量级的提高。这种并行计算为边界元法在大规模复杂工程问题中的应用提供了有效方案。  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号