Influence of Te doping on the dielectric and optical properties of InBi crystals grown by directional freezing

Stoichiometric pure and tellurium (Te) doped indium bismuthide (InBi) were grown using the directional freezing technique in a fabricated furnace. The X-ray diffraction profiles identified the crystallinity and phase composition. The surface topographical features were observed by scanning electron microscopy and atomic force microscopy. The energy dispersive analysis by X-rays was performed to identify the atomic proportion of elements. Studies on the temperature dependence of dielectric constant (?), loss tangent (tanδ), and AC conductivity (σ_ac) reveal the existence of a ferroelectric phase transition in the doped material at 403 K. When InBi is doped with tellurium (4.04 at%), a band gap of 0.20 eV can be achieved, and this is confirmed using Fourier transform infrared studies. The results thus show the conversion of semimetallic InBi to a semiconductor with the optical properties suitable for use in infrared detectors.     

Subsurface macro-inclusions and solidified hook character in aluminum-killed deep-drawing steel slabs

Subsurface macro-inclusions and hooks are detrimental to the surface quality of deep-drawing steel sheets. However, little is known about the relationship between macro-inclusions and hooks. Thus, in this work, two ultralow carbon (ULC) steel slabs and two low carbon (LC) aluminum-killed steel slabs were sampled to study the relationship between hooks and subsurface macro-inclusions, which were detected on the cross-sections of steel samples with an area of 56058 mm2 using an automated scanning electron microscopy/energy-dispersive X-ray spectroscopy system. Results show that subsurface inclusions larger than 200 μm were almost entrapped by hook structures, whereas the location of other inclusions smaller than 200 μm had no obvious dependence on the location of solidified hooks. Furthermore, the number density (ND) of subsurface inclusions larger than 200 μm decreased from 0.02 to 0 cm-2 in ULC steel as the mean hook depth decreased from 1.57 to 1.01 mm. Similar trends were also observed in LC steel. In addition, the detected inclusions larger than 200 μm were concentrated in the region near the slab center (3/8 width-5/8 width), where hook depths were also larger than those at any other locations. Therefore, minimizing the hook depth is an effective way to reduce inclusion-induced sliver defects in deep-drawing steels.     

Effects of basicity and MgO content on the viscosity of the SiO2-CaO-MgO-9wt%Al2O3 slag system

The effects of basicity and MgO content on the viscosity of SiO2-CaO-MgO-9wt%Al2O3 slags with basicity from 0.4 to 1.0 and MgO content from 13wt%to 19wt%were investigated using the rotating cylinder method. A correlation between the viscosity and the slag structure was determined by Fourier transform infrared （FTIR） spectroscopy. It is indicated that the complex network structure of the slag melt is depolymerized into simpler network units with increasing basicity or MgO content, resulting in a continuous decrease in viscosity of the slag. The viscosity is strongly dependent on the combined action of basic oxide components in the slag. Under the present experimental conditions, increasing the basicity is found to be more effective than increasing the MgO content in decreasing the viscosity of the slag. At higher temperatures, the increase of basicity or MgO content does not appreciably decrease the viscosity of the slag, as it does at lower tem-peratures. The calculated activation energy of viscous flow is between 154 and 200 kJ＆#183;mol-1, which decreases with an increase in basicity from 0.4 to 1.0 at a fixed MgO content in the range of 13wt%to 19wt%.     

Microstructure, crystallography and nucleation mechanism of NANOBAIN steel

The microstructure of bainite ferrite in NANOBAIN steel transformed at different temperatures was investigated by scanning electron microscopy, transmission electron microscopy, electron back-scattered diffraction, and vickers hardness tester in detail. It is found that the average width of bainitic ferrite (BF) plates can be refined to be thinner with the reduction of temperature (473–573 K), and the bainitic ferrite plates can reach up to 20–74 nm at 473 K. Crystallographic analysis reveals that the bainitic ferrite laths are close to the Nishiyama-Wasserman orientation relationship with their parent austenite. Temperature shows a significant effect on the variant selection, and a decrease in temperature generally weakens the variant selection. Thermodynamic analyses indicates that the Lacher, Fowler and Guggenheim (LFG) model is more suitable than the Kaufman, Radcliffe and Cohen (KRC) model dealing with NANOBAIN steel at a low temperature range. The free energy change ΔGγ→BF is about ?1500 J·mol?1 at 473 K, which indicates that nucleation in NANOBAIN steel is the shear mechanism. Finally, the formation of carbon poor regions is thermodynamically possible, and the existence of carbon poor regions can greatly increase the possibility of the shear mechanism.     

A dynamic programming algorithm for network selection in 3G/WLAN

An essential characteristic of the 4th Generation （4G） wireless networks is integrating various heterogeneous wireless access networks.This paper considers the network selection for both admission and handoff strategy problems in heterogeneous network of 3G/WLAN.A novel dynamic programming algorithm is proposed by taking heterogeneous network characteristics,user mobility and different service types into account.The specificity of our approach is that it puts the situations in a new model and makes decisions in stages of different states.Simulation results validate that the proposed scheme can obtain better new call blocking and handoff dropping probability performance than traditional schemes while ensuring quality-of-services （QoS） for both real-time and data connections.     

Load compensation research on twicetension for loop anchor cable of inner lining in Yellow River-crossing tunnel

The load compensation equipment for anchor cable named low retraction prestressed anchorage system with twice-tension （referred to as twice-tension anchorage system） is proposed in the paper. Calculation results of loop anchorage prestressing loss （PL） values of inner lining （IL）in Yellow River-crossing tunnel under two anchorage systems, including twice-tension anchorage system and HM （Chinese transliteration is huanmao） anchorage system, are introduced. The software ANSYS is selected to realize the three-dimensional （3D） finite element modeling to accomplish simulation and calculation works under the two anchorage systems, respectively. Stress processes of IL under the two working conditions, of which one is completed cable tensioning （CCT） and the other is water in the tunnel with the designed water pressure （DWP）, are contrasted and analyzed. Impacts of prestressing forces of anchor cables on structural safety under the two anchorage systems are contrasted. The calculation results show that the twice-tension anchorage system can reduce PL effectively and then increase prestresses of wall concrete （WC）. Meanwhile, the anchorage system has the advantages of improving security and stability of tunnel structure, reducing project costs and saving steel consumption. The research work is available to related design and construction of anchor cable, and is worthy of promotion and application.     

Recovery of iron from copper slag by deep reduction and magnetic beneficiation

Aiming at recovering iron from high-iron-content copper slag, this article introduced a combination technology of deep reduction and magnetic beneficiation, investigated the iron recovery efficiency and optimized the technical conditions. When coke powder with 86wt% fixed carbon was used as a reductant, iron was successfully extracted from the copper slag. Under the optimized condition of the coke powder content of 14wt%, the calcium-to-silicon mass ratio (Ca/Si) of 0.2, the roasting temperature of 1300℃, the roasting time of 3 h, the grinding time of 20 min, and the magnetic field intensity of 61 kA·m?1, the iron recovery rate of the copper slag can reach 91.82%, and the extracted iron powder has an iron grade of 96.21%. With the characteristics of high iron grade and low impurity content, the extracted iron powder can be used as high-quality raw materials of weathering steel.     

Effect of light response on the photocatalytic activity of BiOCl x Br1−x in the removal of Rhodamine B from water

BiOClxBr1-x catalysts were synthesized through an alcoholysis method and characterized by X-ray diffraction （XRD）, transmission electron microscopy （TEM）, high-resolution transmission electron microscopy （HRTEM）, and diffuse reflectance spectroscopy （DRS）. The as-prepared photocatalysts were found to be tetragonal crystal structure and lamellar plate morphology. Their band gaps were between 3.44 and 2.83 eV. The effect of light response on the photocatalytic activity of BiOClxBrl-x was investigated by degradation of Rhodamine B （RhB）. Complete removal of RhB from water was realized under simulated sunlight irradiation for 50 min with BiOC10.5Br0.5. Mechanism studies showed that photo- generated holes and superoxide anion radicals played important roles in RhB photodegradation. The results of chemical oxygen demand （COD） confirmed RhB mineralization. The effect of light response on the activity of BiOClxBr1-x was further investigated under monochromatic light irradiation, and BiOCl0.5Br0.5 catalyst exhibited the highest activity. Furthermore, BiOC10.5Br0.5 exhibited high stability, suggesting its practical application for the removal of RhB pollutant from water.     

Design and evaluation of a Laval-type supersonic atomizer for low-pressure gas atomization of molten metals

A Laval-type supersonic gas atomizer was designed for low-pressure gas atomization of molten metals. The principal design objectives were to produce small-particle uniform powders at lower operating pressures by improving the gas inlet and outlet structures and optimizing structural parameters. A computational fluid flow model was developed to study the flow field characteristics of the designed atomizer. Simulation results show that the maximum gas velocity in the atomization zone can reach 440 m·s?1; this value is independent of the atomization gas pressure P₀ when P₀ > 0.7 MPa. When P₀ = 1.1 MPa, the aspiration pressure at the tip of the delivery tube reaches a minimum, indicating that the atomizer can attain the best atomization efficiency at a relatively low atomization pressure. In addition, atomization experiments with pure tin at P₀ = 1.0 MPa and with 7055Al alloy at P₀ = 0.8 and 0.4 MPa were conducted to evaluate the atomization capability of the designed atomizer. Nearly spherical powders were obtained with the mass median diameters of 28.6, 43.4, and 63.5 μm, respectively. Compared with commonly used atomizers, the designed Laval-type atomizer has a better low-pressure gas atomization capability.     

Preparation of composite abrasives by electrostatic self-assembly method and its polishing properties in Cu CMP

The adsorption characteristics of cationic polyelectrolyte poly dimethyl diallyl ammonium chloride （PDADMAC） and anionic polyelectrolyte poly （sodium-p-styrenesulfonate） （PSS） on benzoguanamine formal- dehyde （BGF） particles are investigated. The charging characteristics of BGF particles are changed and con- trolled using electrostatic self-assembly method. A variety of PE,-BGF/SiO2 composite abrasives are obtained. The as-prepared samples are analyzed by zeta potential analysis, transmission electron microscope （TEM） and thermogravimetric （TG） analysis. The composite abrasive slurries are prepared for copper polishing. The poli- shing results indicate that it is SiO2 abrasives, not only coated SiO2 abrasive on polymer particles but also free SiO2 abrasive in slurry, that offer the polishing action. The material removal rates of copper polishing are 264 nm/min, 348 nm/min and 476 nm/min using single SiO2 abrasive slurry, PE0-BGF/SiO2 mixed abrasive slur- ry and PE3-BGF/SiO2 composite abrasive slurry, respectively. The surface roughness Ra of copper wafer （with 5μm×5μm district） is decreased from 0.166 μm to 3.7 nm, 2.6 nm and 1.5 nm, and the surface peak-valley values Rrv are less than 20 nm, 14 nm and 10 nm using these kinds of slurries, respectively. Key words ： chemico-mechanical polishing; polishing slurry; composite abrasives ; polyelectrolyte ; copper     

Exploration on ecological regulation of the reservoirs

Reservoir regulation process in the Yangtze River basin is mainly divided into two types of flood regulation and initiating benefit regulation. The present reservoir management system and operation mode are mainly for dealing with or coordinating of flood control and benefit initiation as well as benefit distribution among various beneficial functions. From the view point of river ecosystem protection, the current regulation mode has two kinds of problems ： firstly, most of the reservoir regulation plans do not consider ecosystem protection at downstream of dams and needs of environment protection in reservoir areas; secondly, integrated regulation or management of water resources is ignored. It is very necessary to improve reservoir regulation mode, bearing problems faced by regulation of the Three Gorges reservoir and issues related to cascade development and regulation in Tuojiang and Minjiang River basins in mind. In accordance with the concept of scientific development, and the philosophy of ＂ensuring a healthy Yangtze River and promoting the harmony between human and water＂, taking flood control, benefit initiation and eco-system as a whole, this paper put forward the basic consideration to improve reservoir regulation as follows ： on the basis of requirements of ecosystem protection at downstream of dams and needs of environment protection in reservoir areas, we should bring the functions of reservoir such as flood control and benefit initiation into full play, control the negative influence to the ecosystem at downstream of dams and the environment in reservoir areas in an endurable scope, and restore the ecosystem and the environment step by step. This paper put forward the relevant regulation process aiming at the idiographic problems such as protection of ecosystem at downstream of dams and environment in reservoir areas, protection of aquatic wildlife species and fish species, regulation of sediment and protection of wetland.     

Effect of dietary supplementation on improvement of growth and immune function of broilers

The purpose of this investigation was to evaluate the effect of a dietary supplement （Mirigen TM）, a fungal cell wall derivative product, as a new generation alternative to antibiotics, on the growth and the innate and adaptive immune functions in broilers from birth to 45 d of age. Newborn chicken were randomly assigned to one of three groups： G 1 （n=150） controls no supplement fed; G2 （n=150） is fed with dietary supplement at a designed regular dose （0.5 %, weight of additive to food）; G3 （n= 150） is fed with dietary supplement at double doses （1%）. All three groups were housed in the same conditions. Body weight and blood were taken on day 1, 14, 28 and 45. Medications used and costs/treatment were recorded for each group. The whole blood was used to purify heterophils for reactive oxygen species （ROS） generation and E coli killing abilities examination assays, and the serum samples were preserved in freezer for enzyme linked immunosorbent assays （ELISAs） to determine concentration of macrophage inflammatory protein-1β （MIP-1β）, CD4/CD8, interferon-y （IFN-y）, and titers of antibody against Newcastle disease virus （NDV）. Group differences were analyzed using analysis of variance （ANOVA） algorithm （S-Plus）. There was no significant birth weight difference in three groups. After 45 d growth, the dietary supplement treated groups had significantly higher body weight gain （BWG） with lower mortality rate if compared to the untreated control group （P〈0.05）. Their BWG and mortality rate were 2.23 kg and 10 % in GI （control group）, 2.89 kg and 2 % in G2 （experimental group, 0.5 % dose）, and 2.77 kg and 1% in G3 （experimental group, 1% dose）, respectively. Heterophil ROS generation in treated groups were markedly improved through the addition of dietary supplement in both regular and double doses to the diet （P〈 0.05）. The ability of heterophil to kill E coli was also significantly improved in dietary supplement treated groups （P〈0.01）. Comparing to control group, there was significantly higher serum IFN-y concentration in treated groups （P〈0.05） on day 45. The CD4/CD8 was also improved in treated groups （P〈0.05）. Newcastle di-sease is the most prevalent avian disease, and vaccination is an effective method to protect the animals from the virus infection. In our study, it is found G2 and G3 that fed with dietary supplement had higher antibody titers against NDV after vaccination （P〈0.01） and the antibodies lasted longer. Results from this study demonstrated dietary supplement to broilers improved the immune capabilities of immune cells, which are vital to the establishment of immune response against pathogens, thereby, to improve chicken＇ s health and growth and reduce medication cost in chicken farming.     

Global Lipschitz Stability in an Inverse Problem for the Non-stationary Transport Equation

An inverse problem of determining the source term of the non-stationary transport equation was considered.The extra lateral boundary condition was chosen as the observation data.Based on a Carleman estimate on the non-stationary transport equation,a global Lipschitz stability for the inverse problem was proved.     

大果水晶梨与其褐色突变体多酚氧化酶及过氧化物酶同工酶差异(简报)

大果水晶梨果皮为绿色,2007年在其植株上发现一果实呈褐色的变异枝,经2008-2009年嫁接试验后确定为遗传性变异。与原品种比较,褐色突变体果实多了一层褐色木栓层。     

Mycelial fermentation and medicinal properties of a valuable medicinal fungus Cordyceps sinensis Cs-HK1

Cordyceps sinensis （Cs） or Dongchongxiacao in Chinese is a rare and precious medicinal mushroom. In this work, a Tolypocladium sp. fungus named Cs-HK1 was isolated from a natural Cs fruiting body, and its ultraviolet （UV）, infrared （IR） and high-performance liquid chromatography （HPLC） spectra all exhibited high degrees of matching to those of natural Cs, indicating the similarity of chemical composition. A crude polysaccharide （PS） fraction isolated from Cs-HKI fungal mycelium showed significant antitumor activity, inhibiting melanoma tumor growth in mice. The PS-treated mice showed significantly higher serum interferon-y （IFN-y） level and higher proliferation rate of lymphocytes ex vivo than the control animals, suggestive of the immunomodulatory activity of the PS fraction. In cell cultures, the PS fraction caused a significant and dose-dependent inhibitory effect on the proliferation of two cancer cell lines, B16/neu mouse melanoma and MDA-MB-231 human breast cancer cells, but not on normal spleen lymphocytes in vitro. Most of these bioactivities of the Cs- HK1 fungus were comparable to or even greater than those of natural Cs. The results showed that Cs-HK1 fungus may be a functional substitute for the natural Cs in health food and herbal medicine.     

Dynamic recrystallization and precipitation in high manganese austenitic stainless steel during hot compression

Dynamic recrystallization and precipitation in a high manganese austenitic stainless steel were investigated by hot compression tests over temperatures of 950–1150℃ at strain rates of 0.001 s?1-1 s?1. All the flow curves within the studied deformation regimes were typical of dynamic recrystallization. A window was constructed to determine the value of apparent activation energy as a function of strain rate and deformation temperature. The kinetics of dynamic recrystallization was analyzed using the Avrami kinetics equation. A range of apparent activation energy for hot deformation from 303 kJ/mol to 477 kJ/mol is obtained at different deformation regimes. Microscopic characterization confirms that under a certain deformation condition (medium Zener-Hollomon parameter (Z) values), dynamic recrystallization appears at first, but large particles can not inhibit the recrystallization. At low or high Z values, dynamic recrystallization may occur before dynamic precipitation and proceeds faster. In both cases, secondary phase precipitation is observed along prior austenite grain boundaries. Stress relaxation tests at the same deformation temperatures also confirm the possibility of dynamic precipitation. Unexpectedly, the Avrami’s exponent value increases with the increase of Z value. It is associated with the priority of dynamic recrystallization to dynamic precipitation at higher Z values.     

Automatic Collecting Representative Logo Images from the Internet

With the explosive growth of commercial Iogos, high quality logo images are needed for training logo detection or recognition systems, especially for famous Iogos or new commercial brands. This paper focuses on automatic collecting representative logo images from the internet without any human labeling or seed images. We propose multiple dictionary invariant sparse coding to solve this problem. This work can automatically provide prototypes, representative images, or weak labeled training images for logo detection, logo recognition, trademark infringement detection, brand protection, and ad-targeting. The experiment results show that our method increases the mean average precision for 25 types of Iogos to 80.07% whereas the original search engine results only have 32% representative logo images. The top images collected by our method are accurate and reliable enough for practical applications in the future.     

General design of Sutong Bridge

The main span of Sutong Bridge is a double-pylon, double-plane cable-stayed bridge with steel box girder, which has the world＇ s longest central span of 1 088 m within cable-stayed bridges. To overcome problems caused by severe meteorological conditions, perplexing hydrological conditions, deep buried bedrock and higher navigation level, many new technics and methods were created. Keys including structural system, steel box girder, stayed cable, tower, pier, tower foundation, collision avoidance system, wind-resistance, seismic-resistance, structural nonlinear response and structural static stability were presented individually in this paper.     

An adaptive pipelining scheme for H.264/AVC CABAC decoder

An adaptive pipelining scheme for H.264/AVC context-based adaptive binary arithmetic coding （CABAC） decoder for high definition （HD） applications is proposed to solve data hazard problems coming from the data dependencies in CABAC decoding process.An efficiency model of CABAC decoding pipeline is derived according to the analysis of a common pipeline.Based on that,several adaptive strategies are provided.The pipelining scheme with these strategies can be adaptive to different types of syntax elements （SEs） and the pipeline will not stall during decoding process when these strategies are adopted.In addition,the decoder proposed can fully support H.264/AVC high 4 ∶ 2 ∶ 2 profile and the experimental results show that the efficiency of decoder is much higher than other architectures with one engine.Taking both performance and cost into consideration,our design makes a good tradeoff compared with other work and it is sufficient for HD real-time decoding.