烧结铁矿中FeO含量对其在富氢高炉中还原行为的影响

Japan started the national project “COURSE 50” for CO₂ reduction in the 2000s. This project aimed to establish novel technologies to reduce CO₂ emissions with partially utilization of hydrogen in blast furnace-based ironmaking by 30% by around 2030 and use it for practical applications by 2050. The idea is that instead of coke, hydrogen is used as the reducing agent, leading to lower fossil fuel consumption in the process. It has been reported that the reduction behavior of hematite, magnetite, calcium ferrite, and slag in the sinter is different, and it is also considerably influenced by the sinter morphology. This study aimed to investigate the reduction behavior of sinters in hydrogen enriched blast furnace with different mineral morphologies in CO–CO₂–H₂ mixed gas. As an experimental sample, two sinter samples with significantly different hematite and magnetite ratios were prepared to compare their reduction behaviors. The reduction of wustite to iron was carried out at 1000, 900, and 800°C in a CO–CO₂–H₂ atmosphere for the mineral morphology-controlled sinter, and the following findings were obtained. The reduction rate of smaller amount of FeO led to faster increase of the reduction rate curve at the initial stage of reduction. Macro-observations of reduced samples showed that the reaction proceeded from the outer periphery of the sample toward the inside, and a reaction interface was observed where reduced iron and wustite coexisted. Micro-observations revealed three layers, namely, wustite single phase in the center zone of the sample, iron single phase in the outer periphery zone of the sample, and iron oxide-derived wustite FeO and iron, or calcium ferrite-derived wustite 'FeO' and iron in the reaction interface zone. A two-interface unreacted core model was successfully applied for the kinetic analysis of the reduction reaction, and obtained temperature dependent expressions of the chemical reaction coefficients from each mineral phases.     

Mg和La对Ca–Ti 处理钢中夹杂物演变和组织的影响

The evolution of inclusions and the formation of acicular ferrite (AF) in Ca–Ti treated steel was systematically investigated after Mg and La addition. The inclusions in the molten steel were Ca–Al–O, Ca–Al–Mg–O, and La–Mg–Ca–Al–O after Ca, Mg, and La addition, respectively. The type of oxide inclusion in the final quenched samples was the same as that in the molten steel. However, unlike those in molten steel, the inclusions were Ca–Al–Ti–O + MnS, Ca–Mg–Al–Ti–O + MnS, and La–Ca–Mg–Al–Ti–O + MnS in Mg-free, Mg-containing, and La-containing samples, respectively. The inclusions distributed dispersedly in the La-containing sample. In addition, the average size of the inclusions in the La-containing sample was the smallest, while the number density of inclusions was the highest. The size of effective inclusions (nucleus of AF formation) was mainly in the range of 1–3 μm. In addition, the content of ferrite side plates (FSP) decreased, while the percentage of AF increased by 16.2% due to the increase in the number of effective inclusions in the La-containing sample in this study.     

氧化锌矿物浸出渣中铅、锶的提取及动力学分析

NH₄HCO₃ conversion followed by HCl leaching was performed and proven to be effective in extracting Pb and Sr from zinc extracted residual. The mechanism and operating conditions of NH₄HCO₃ conversion, including molar ratio of NH₄HCO₃ to zinc extracted residual, NH₄HCO₃ concentration, conversion temperature, conversion time, and stirring velocity, were discussed, and operating conditions were optimized by the orthogonal test. Experimental results indicate that NH₄HCO₃ conversion at temperatures ranging from 25 to 85°C follows the shrinking unreacted core model and is controlled by inner diffusion through the product layer. The extraction ratios of Pb and Sr under optimized conditions reached 85.15% and 87.08%, respectively. Moreover, the apparent activation energies of Pb and Sr were 13.85 and 13.67 kJ·mol?1, respectively.     

摩擦焊接碳钢（EN24）和镍基高温合金（IN718）的显微组织和力学性能

Continuous-drive rotary friction welding was performed to join cylindrical specimens of carbon steel (EN24) and nickel-based superalloy (IN718), and the microstructures of three distinct weld zones—the weld interface (WI)/thermo-mechanically affected zone (TMAZ), the heat-affected zone (HAZ), and the base metal—were examined. The joint was observed to be free of defects but featured uneven flash formation. Electron backscatter diffraction (EBSD) analysis showed substantial changes in high-angle grain boundaries, low-angle grain boundaries, and twin boundaries in the TMAZ and HAZ. Moreover, significant refinement in grain size (2–5 μm) was observed at the WI/TMAZ with reference to the base metal. The possible causes of these are discussed. The microhardness profile across the welded joint shows variation in hardness. The changes in hardness are ascribed to grain refinement, phase transformation, and the dissolution of strengthening precipitates. The tensile test results reveal that a joint efficiency of 100% can be achieved using this method.     

汽车暴露面板带有表面条状缺陷的夹杂物分布特征分析:一种定量电解方法

The specific distribution characteristics of inclusions along with the sliver defect were analyzed in detail to explain the formation mechanism of the sliver defect on the automobile exposed panel surface. A quantitative electrolysis method was used to compare and evaluate the three-dimensional morphology, size, composition, quantity, and distribution of inclusions in the defect and non-defect zone of automobile exposed panel. The Al₂O₃ inclusions were observed to be aggregated or chain-like shape along with the sliver defect of about 3–10 μm. The aggregation sections of the Al₂O₃ inclusions are distributed discretely along the rolling direction, with a spacing of 3–7 mm, a length of 6–7 mm, and a width of about 3 mm. The inclusion area part is 0.04%–0.16% with an average value of 0.08%, the inclusion number density is 40 mm?2 and the inclusion average spacing is 25.13 μm. The inclusion spacing is approximately 40–160 μm, with an average value of 68.76 μm in chain-like inclusion parts. The average area fraction and number density of inclusions in the non-defect region were reduced to about 0.002% and 1–2 mm?2, respectively, with the inclusion spacing of 400 μm and the size of Al₂O₃ being 1–3 μm.     

在酸性溶液中加压氧化三价砷离子和二价铁离子

The co-oxidation of As(III) and Fe(II) in acidic solutions by pressured oxygen was studied under an oxygen pressure between 0.5 and 2.0 MPa at a temperature of 150°C. It was confirmed that without Fe(II) ions, As(III) ions in the solutions are virtually non-oxidizable by pressured oxygen even at a temperature as high as 200°C and an oxygen pressure up to 2.0 MPa. Fe(II) ions in the solutions did have a catalysis effect on the oxidation of As(III), possibly attributable to the production of such strong oxidants as hydroxyl free radicals (OH·) and Fe(IV) in the oxidation process of Fe(II). The effects of such factors as the initial molar ratio of Fe(II)/As(III), initial pH value of the solution, oxygen pressure, and the addition of radical scavengers on the oxidation efficiencies of As(III) and Fe(II) were studied. It was found that the oxidation of As(III) was limited in the co-oxidation process due to the accumulation of the As(III) oxidation product, As(V), in the solutions.     

采用超声组装与滚压工艺制备铝–碳纳米管复合材料

This study introduced a novel fabrication of aluminum–carbon nanotube (CNT) composites by employing bulk acoustic waves and accumulative roll bonding (ARB). In this method, CNT particles were aligned using ultrasonic standing wave in an aqueous media, and the arrayed particles were precipitated on the aluminum plate substrate. Then, the plates rolled on each other through the ARB process with four passes. Optical and scanning electron micrographs demonstrated the effective aligning of CNTs on the aluminum substrate with a negligible deviation of arrayed CNTs through the ARB process. The X-ray diffraction pattern of the developed composites showed no peaks for carbon and aluminum carbide. In addition, tensile tests showed that the longitudinal strength of the specimens processed with aligned CNTs was significantly greater than that of the specimens with common randomly dispersed particles. The proposed technique is beneficial for the fabrication of Al–CNT composites with directional mechanical strength.     

活化天然矿石选择性还原二氧化碳为无定形碳

Natural magnetite formed by the isomorphism substitutions of transition metals, including Fe, Ti, Co, etc., was activated by mechanical grinding followed by H₂ reduction. The temperature-programmed reduction of hydrogen (H₂-TPR) and temperature-programmed surface reaction of carbon dioxide (CO₂-TPSR) were carried out to investigate the processes of oxygen loss and CO₂ reduction. The samples were characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), and energy-dispersive X-ray spectroscopy (EDS). The results showed that the stability of spinel phases and oxygen-deficient degree significantly increased after natural magnetite was mechanically milled and reduced in H₂ atmosphere. Meanwhile, the activity and selectivity of CO₂ reduction into carbon were enhanced. The deposited carbon on the activated natural magnetite was confirmed as amorphous. The amount of carbon after CO₂ reduction at 300°C for 90 min over the activated natural magnetite was 2.87wt% higher than that over the natural magnetite.     

民间法正义观的转型

研究了国家法的抽象正义观与民间法的情理正义观,认为西方国家法的抽象正义观与东方民间法的情理正义观存在实质的不同,原因在于思维方式、超验与经验传统、政治结构的差别。在现代法治理念下,传统民间法所代表的正义观将向混合正义观转型,西方法治所代表的国家法抽象正义观是其骨架。     

发动机转动惯量的实验测定

发动机转动惯量是发动机系统动态模型的一个重要参数,一般需要通过试验测取发动机转速衰减曲线,再由曲线拟合而得。在文中提出一种试验曲线的全程拟合法,比以往的标定转速点拟合法可以取得更高的精度。     

关于一维非自治时滞系统点态退化的例子

给出了一维非自治时滞系统点态退化的几个例子。     

关于农业区划地图集中的统一协调问题

图集的统一协调,对图集质量有很大影响。本文是作者在编制北京市农业区划地图集的实践基础上,根据地图信息传输论的观点,对农业区划地图集的统一协调的内容及方法进行了探讨。试图总结编制这类图集的统一协调模式,以供读者编图时参考。     

辽阳职业技术学院高尔夫学院发展现状研究

采用问卷调查法、文献资料法、数理统计法对辽阳职业技术学院二级分院高尔夫学院成立三年来招生、专业设置、教师队伍与实习实训等现状进行深入调查与分析,结果表明:在招生方面,高尔夫学院目前还未能得到家长的充分认可,招生人数不多;专业设置单一,实践教学及社会服务能力薄弱;实习实训条件较好,但仍需进一步完善;教师队伍建设相对滞后.针对上述情况,给出促进高尔夫学院稳步发展的建议.     

膨胀土路基沉降的可靠度分析

针对膨胀土路基沉降的不稳定性和随机性等特点，以膨胀土的膨胀率、线收缩系数、初始含水量、工后沉降期始末的孔隙比变化量和固结度变化量、工后沉降期末的含水量等为基本变量，提出了膨胀土路基沉降的可靠度分析方法和可靠度指标的迭代计算步骤，并就具体工程实例进行了膨胀土路基沉降可靠度计算．结果表明按强度和稳定性设计原则设计的路基的工后沉降超过容许沉降的失效概率较大。     

接受美学的期待之路——读者接受与文学的创新

文学发展的动力之一在于创新。在接受美学诞生之前,学者们往往从作家的角度讨论文学创新问题。本文用接受美学的理论探讨文学创新的问题。笔者将文学创新的标准与读者接受相结合,就创新的三个方式与期待视野的方法论进行了初步的探讨。最后得出的结论是:读者期待视野的提高是作家作品创新的主要依据,作家在文学创作中应该充分考虑读者的接受才能做到创新。     

宏观收入分配不等性分析

宏观收入量的分配不仅反映一个国家总体消费的基础水平，而且影响到各阶层消费水平及消费方式．虽然一个国家的宏观收入量的分配不可能绝对平等，但是不等性的大小往往影响到社会和经济的发展，影响到社会的稳定．本文采用洛伦茨曲线、基尼系数来描述宏观收入的不等性，并结合实际情况对我国宏观收入的不等性进行了具体的分析．     

过热器连续爆管事故分析

通过对一起锅炉过热器爆管事故的分析 ,找出了过热器爆管事故的原因 ,提出了改进意见 ,收到了显著的效果     

曲面“侧”概念的“参照物”理解法

曲面“侧”是一个重要而难以理解的概念 ,本文对曲面“侧”概念的讲授方法进行了探讨 ,给出了曲面“侧”概念的“参照物”理解法 ,通过实践证明 ,效果良好。