Electroch emical properties and interfacial reactions of LiNi0.5Mn1.5O4-δ nanorods

LiNi0.5Mn1.5O4-δ which possesses a high voltage of 4.7 V vs.Li+/Li and stable structure has been considered as a promising cathode material for high energy Li-ion batteries.In this study,well-crystalli...     

Zr-pillared montmoril lonite supported cobalt nanoparticles for Fischer – Tropsch synthesis

In this article Fischer–Tropsch(FT) synthesis was studied over cobalt nanoparticles supported on modifed Montmorillonite(Zr-PILC).Co-loaded/Zr-PILC catalysts were synthesized by hydrothermal methods and were characterized by XRD,XRF,BET,H2-TPR,TGA and SEM techniques.FT reactions were carried out in fxed bed microreactor(T 225 1C,260 1C and 275 1C,P 1,5 and 10 bars).The FT-products obtained over Co-loaded/Zr-PILC catalysts showed increased selectivity of C2–C12hydrocarbons and decreased selectivity towards CH4and higher molecular weight hydrocarbons(C21) at a TOS of 2–30 h as compared to the Co-loaded/NaMMT catalysts.With increase in reaction temperature from225 1C to 275 1C,CO-conversion and CH4selectivity increases while that of C5+hydrocarbons decreases.Decrease in CH4selectivity while increase in C5+hydrocarbons and CO-conversion were observed on increasing the pressure of reaction.     

Effect of CuO addition on the sintering temperature and microwave dielectric properties of CaSiO3– Al2O3 ceramics

CuO-doped CaSiO3–1 wt% Al2O3 ceramics were synthesized via a traditional solid-state reaction method, and their sintering behavior,microstructure and microwave dielectric properties were investigated. The results showed that appropriate CuO addition could accelerate the sintering process and assist the densification of CaSiO3–1 wt% Al2O3 ceramics, which could effectively lower the densification temperature from1250 1C to 1050 1C. However, the addition of CuO undermined the microwave dielectric properties. The optimal amount of CuO addition was found to be 0.8 wt%, and the derived CaSiO3–Al2O3ceramic sintered at 1100 1C presented good microwave dielectric properties of εr?7.27,Q f?16,850 GHz and τf? 39.53 ppm/1C, which is much better than those of pure CaSiO3 ceramic sintered at 1340oC(Q f?13,109 GHz).The chemical compatibility of the above ceramic with 30 Pd/70 Ag during the cofiring process has also been investigated, and the result showed that there was no chemical reaction between palladium–silver alloys and ceramics.& 2014 Chinese Materials Research Society. Production and hosting by Elsevier B.V. All rights reserved.     

Size-manipulat ion, compacti on and electrical properties of barium manganite nanorods synthesized via the CHM method

A composite-hydroxide mediated method was employed to synthesize barium manganite nanorods.Diameter,surface smoothness and uniformity of these nanorods were optimized by varying reaction temperature and reaction time.The rods with an average diameter of 200 nm and length of1–1.5 μm were obtained at optimum conditions of 200 1C/48 h.The dielectric study of these rods reveals that they have higher value of dielectric constant at lower frequencies which was attributed to the interfacial and rotational type polarizations.Similarly,the increase in dielectric constant with temperature was attributed to the thermal activation of such polarizations.Furthermore,the analysis of ln(J) vs.E1/2characteristics in the temperature range of 300–400 K shows that possible operative conduction mechanism was of Poole–Frenkel type.The value of βexp was found to be 4.85 times greater than the expected theoretical value of feld lowering coeffcient with an internal feld enhancement factor ofα2 23.5.This high value of βexp may be due to some localized electric felds existing inside the sample.     

Phase stability and thermal conductivity of ytterbia and yttria co-doped zirconia

Rare earth oxides doping has been extensively investigated as one of the effective methods to lower thermal conductivity of 4.55 mol% Y2O3stabilized ZrO2(YSZ) thermal barrier coatings(TBCs).In the present work,5–6 mol% Yb2O3and Y2O3co-doped ZrO2ceramics were synthesized by solid reaction sintering at 1600 1C.The phase stability of the samples after heat treatment at 1500 1C was investigated.Yb2O3and Y2O3co-doped zirconia,especially when Yb2O3/Y2O3≥1,contained less monoclinic phase than single Yb2O3or Y2O3phase doped zirconia,indicating that co-doped zirconia was more stable at high temperature than YSZ.The thermal conductivity of the 3 mol% Yb2O3+3 mol% Y2O3co-doped ZrO2was 1.8 W m 1K 1at 1000 1C,which was more than 20% lower than that of YSZ.     

Novel approaches to produce Al2O3– TiC/TiCN– Fecomposite powders directly from ilmenite

Al2O3 –TiC/TiCN–Fe composite powders were successfully prepared directly from ilmenite at 1300–1400℃.The effects of Al/C ratio,sintering atmosphere,and reaction temperature and time on the reaction products were investigated.Results showed that the nitrogen atmosphere was bene cial to the reduction of ilmenite and the formation of Al2O3 –TiC/TiCN–Fe composite powders.When the reaction temperature was between 600 and 1100℃,the intermediate products,TiO2,Ti3O5 and Ti4O7 were found,which changed to TiC or TiCN at higher temperature.Al/C ratio was found to affect the reaction process and synthesis products.When Al addition was 0.5 mol,the Al2O3 phase did not appear.The content of carbon in TiCN rose when the reaction temperature was increased.     

Core loss analysis of Finemet type nanocrystalline alloy ribbon with different thickness

Nanocrystalline soft magnetic materials are widely used in power electronic applications due to their high permeability,magnetization and low core loss.In this paper,Fe_(73.5)Cu_1Nb_3Si_(15.5)B_7(at%)nanocrystalline alloy ribbons,with ultra-thin thickness of 14μm,and also 18 and 22μm,were prepared by a planar flow casting method with a single roller device.Soft magnetic properties of these ribbons were analyzed after nanocrystallization annealing.The experiments were conducted on toroidal samples using IWATSU B-H Analyzer over a frequency range of 10–100 kHz,at induction amplitudes of 100–500 m T,at room temperature.It was found that the excess eddy current loss P_(ex)was the dominant factor in the overall core loss above 10 k Hz.The toroidal samples made of the 14μm thickness ribbon exhibit very low total core loss of 48 W/kg at a frequency of100 kHz and magnetic flux density of 300 mT.The ratio of the P_(ex)was up to 89%at 100 kHz.The ribbon with lower thickness exhibits lower P_(ex)and therefore lower total core loss.The domain structure evidences were found.It indicates that the ribbons with small thickness are preferable for application in high frequency condition.     

Facile synthesis of nanosized sodium magnesium hydride, NaMgH3

The ternary magnesium hydride NaMgH 3 has been synthesised via reactive milling techniques.The method employed neither a reactive H2 atmosphere nor high pressure sintering or other post-treatment processes.The formation of the ternary hydride was studied as a function of milling time and ball:powder ratio.High purity NaMgH 3 powder(orthorhombic space group Pnma,a 5.437(2),b 7.705(5),c 5.477(2) ;Z 4) was prepared in 5 h at high ball:powder ratios and characterised by powder X-ray diffraction(PXD),Raman spectroscopy and scanning electron microscopy/energy dispersive X-ray spectroscopy(SEM/EDX).The products formed sub-micron scale(typically 200-400 nm in size) crystallites that were approximately isotropic in shape.The dehydrogenation behaviour of the ternary hydride was investigated by temperature programmed desorption(TPD).The nanostructured hydride releases hydrogen in two steps with an onset temperature for the first step of 513 K.     

Bionic titania coating carbon multi-layer material derived from natural leaf and its superior photocatalytic performance

Bionic titania coating carbon multi-layer material was fabricated by employing canna leaves as substrate and carbon precursor. Titania nanocrystals were assembled and coated on the natural films. The carbonation treatment under pure N_2 atmosphere yielded the ultrathin multi-film hybrid material. The carbon layer was coated with small anatase titania crystallite(8–10 nm) and possessed a highly specific surface area of 248.3 m~2 g~(-1). Examination using UV–visible spectrophotometer(UV–vis) showed that the band gap of the multi-layer material was reduced to 2.75 eV, and the hydrogen production by photocatalytic splitting of water under visible light irradiation was about 302 μmol g~(-1) after six hour.     

Synthesis, structure, and optical properties of manganese phthalocyanine thin films and nanostructures

Manganese phthalocyanine(MnPc) nanostructures with different morphologies were prepared on porous anodic alumina oxide(AAO) at different substrate temperature(T_S=50 ℃,80 ℃,120 ℃,180 ℃,240 ℃) in an organic molecular beam deposition(OMBD) system.The nanostructures morphologies were studied using scanning electron microscopy(SEM) and the results showed that the nanostructures morphologies could be modulated by the control of T_S,as a result,the continuous film was obtained at 50 ℃,whereas the nanorods(NRs),nanoribbons(NBs),nanowires(NWs),nanosheets(NSs) and nanoparticles(NPs) were facilely generated as T_S increased.At the same time,the density and the uniformity of the nanostructures decreased.The results of X-ray diffraction(XRD) indicated that only the(3-phase polymorph formed throughout the growth process irrelevant to the T_S.Additionally,the ultraviolet visible(UV-Vis) absorption spectra demonstrated that the main absorption bands of MnPc nanostructures showed a remarkable band broadening as the T_S was increased.     

Synthesis of dental resins using diatomite and nano-sized SiO2 and TiO2

The mechanical properties of dental composites were improved by porous diatomite and nano-sized silica (OX-50) used as co-fillers.The resin composites,filled with silanized OX-50 and silanized diatomit...     

The enhanced corrosion resistance of UMAO coatings on Mg by silane treatment

The surface silanization was carried out on ultrasonic micro-arc oxidation(UMAO) coatings on pure magnesium using KH550 as silane coupling agent(SCA). The surface morphology, chemical bonds and corrosion resistance of the silane films were investigated by scanning electron microscope(SEM), Fourier transform infrared spectroscopy(FTIR) and electrochemical workstation, respectively. The results showed that hybrid coatings were successfully prepared on pure magnesium by UMAO-Na OH(1 mol/L, 2 mol/L, 3 mol/L)-SCA processing. The organic films with Si–O–Mg bonds are helpful for the reduction of the pores in UMAO coatings. The pores decreased with increasing Na OH concentration. Compared with single UMAO treatment, the corrosion potentials(Ecorr) of magnesium plates with UMAO-Na OH(1 mol/L,2 mol/L, 3 mol/L)-SCA treatment increased by 29 m V, 53 m V and 75 m V, respectively, meanwhile the corrosion current density(Icorr) reduced one to two orders of magnitude. It indicated that the corrosion resistance of the coatings was improved by silane treatment.     

Effect of Co addition on crystallization and magnetic properties of FeSiBPCu alloy

The effects of Co addition on the microstructure,crystallization processes and soft magnetic properties of(Fe1 xCox)83Si4B8P4Cu1(x?0.35,0.5,0.65)alloys were investigated.The experimental results demonstrated that the addition of Co decreased the thermal stability against crystallization of the amorphous phase,and thus improved the heat treatment temperature of this alloy.Fe Co Si BPCu nanocrystalline alloys with a dispersedα0-Fe Co phase were obtained by appropriately annealing the as-quenched ribbons at 763 K for 10 min.Theα0-Fe Co with grains size ranging from 9 to 28 nm was identified in primary crystallization.The coercivity(Hc)markedly increased with increasing x and exhibited a minimum value at x0.35,while the saturation magnetic flux density(Bs)shows a slight decrease.The(Fe0.65Co0.35)83Si4B8P4Cu1nanocrystalline alloy exhibited a high saturation magnetic flux density Bsof 1.68 T,a low coercivity,Hcof 5.4 A/m and a high effective permeability meof 29,000 at 1 k Hz.     

Activated carbon derived from rice husk by NaOH activation and its application in supercapacitor

Four activated carbon(AC) samples prepared from rice husk under different activation temperatures have been characterized by N2adsorption–desorption isotherms, thermogravimetric analysis(TGA–DTA), Fourier transform infrared spectroscopy(FTIR) and scanning electron microscopy(SEM). The specific surface area of AC sample reached 2681 m2 g 1under activation temperature of 800 1C. The AC samples were then tested as electrode material; the specific capacitance of the as-prepared activated carbon electrode was found to be 172.3 F g 1using cyclic voltammetry at a scan rate of 5 mV s 1and 198.4 F g 1at current density 1000 mA g 1in the charge/discharge mode.& 2014 Chinese Materials Research Society. Production and hosting by Elsevier B.V. All rights reserved.     

Highly stable N-containing polymer-based Fe/Nx/C electrocatalyst for alkaline anion exchange membrane fuel cell applications

A cost-effective electrocatalyst with high activity and stability was developed. The Fe-Nx and pyridinic-N active sites were embedded in nitrogen-doped mesoporous carbon nanomaterial by carbonization at high temperature. The electrocatalyst exhibited excellent electrochemical performance for the oxygen reduction reaction, with high onset potential and half-wave potential values (E_onset = 1.10 ?V and E_1/2 ?= ?0.944 ?V) than 20 ?wt % Pt/C catalyst (1.04 and 0.910 ?V). The mass activity of the Schiff base network (SNW) based SNW-Fe/N/C@800° electrocatalyst (0.64 ?mA ?mg^?1 @ 1 ?V) reached about half of the commercial Pt/C electrocatalyst (1.35 ?mA ?mg^?1 @ 1 ?V). The electrocatalyst followed the 4-electron transfer mechanism due to very low hydrogen peroxide yield (H₂O₂ ?< ?1.5%) was obtained. In addition, this electrocatalyst with dual active sites showed high stability during cyclic voltammetry and chronoamperometry measurements. More importantly, the electrocatalyst also demonstrated the power density of 266 ?mW ?cm^?2 in the alkaline anions exchange membrane fuel cell (AEMFC) test, indicating its prospective application for fuel cells.     

Microstructure and oxidation resistance of SiC–MoSi2 multi-phase coating for SiC coated C/C composites

In order to improve the anti-oxidation of C/C composites, a SiC–MoSi2multi-phase coating for SiC coated carbon/carbon composites(C/C)was prepared by low pressure chemical vapor deposition(LPCVD) using methyltrichlorosilane(MTS) as precursor, combined with slurry painting from MoSi2 powder. The phase composition and morphology were analyzed by scanning electron microscope(SEM) and X-ray diffraction(XRD) methods, and the deposition mechanism was discussed. The isothermal oxidation and thermal shock resistance were investigated in a furnace containing air environment at 1500 1C. The results show that the as-prepared SiC–MoSi2coating consists of MoSi2 particles as a dispersing phase and CVD–SiC as a continuous phase. The weight loss of the coated samples is 1.51% after oxidation at 1500 1C for 90 h, and 4.79% after 30 thermal cycles between 1500 1C and room temperature. The penetrable cracks and cavities in the coating served as the diffusion channel of oxygen, resulted in the oxidation of C/C composites, and led to the weight loss in oxidation.     

Effect of Sr on microstructure and aging behavior of Mg–14Li alloys

The as-cast and as-extruded Mg–14 wt%Li–x Sr ( x=0.14, 0.19, 0.39 wt%) alloys were,respectively, prepared through a simple alloying process and hot extrusion. The effects of Sr addition on microstructure and aging behavior of the Mg–14 wt%Li–xSr alloys were studied. The results indicated that β(Li) and Mg2Sr were the two primary phases in the microstructures of both as-cast and as-extruded Mg–14 wt%Li–xSr alloys. Interestingly, with the increase of Sr content from 0.14 wt% to 0.39 wt%, the grain sizes of the as-cast and as-extruded Mg–14 wt%Li–xSr alloys markedly decreased from 5000mm and 38mm to 330 mm and 22mm respectively, while no obvious changes of the micro-hardness and microstructure of the as-extruded alloys were observed during the aging treatment.     

Minor-alloyed Cu-Ni-Si alloys with high hardness and electric conductivity designed by a cluster formula approach

Cu-Ni-Si alloys are widely used due to their good electrical conductivities in combination with high strength and hardness. In the present work, minor-alloying with M =(Cr, Fe, Mo, Zr) was conducted for the objective of further improving their hardness while maintaining their conductivity level. A cluster-plus-glue-atom model was introduced to design the compositions of M-alloyed Cu-Ni-Si alloys, in which an ideal composition formula[(Ni,Si,M)-Cu_(12)]Cu_3(molar proportion) was proposed. To guarantee the complete precipitation of solute elements in fine δ-Ni_2 Si precipitates, the atomic ratio of(Ni,M)/Si was set as 2/1. Thus the designed alloy series of Cu_(93.75)(Ni/Zr)_(3.75)Si_(2.08)(Cr/Fe/Mo)_(0.42)(at%) were arc-melted into ingots under argon atmosphere, and solidsolutioned at 950 ℃ for 1 h plus water quenching and then aged at 450 ℃ for different hours. The experimental results showed that these designed alloys exhibit high hardness(HV 1.7 GPa) and good electrical conductivities(≥ 35% IACS). Specifically, the quinary Cu_(93.75)Ni_(3.54)Si_(2.08)(Cr/Fe)_(0.42)Zr_(0.21) alloys(Cu-3.32 Ni-0.93 Si-0.37(Cr/Fe)-0.30 Zr wt%) possess both a high hardness with HV = 2.5-2.7 GPa, comparable to the highstrength KLFA85 alloy(Cu-3.2 Ni-0.7 Si-1.1 Zn wt%,HV= 2.548 GPa),and a good electrical conductivity(35-36% IACS).     

Phase analysis of AlFe2B2 by synchrotron X-ray diffraction, magnetic and Mössbauer studies

The structural and magnetic properties of essentially phase pure AlFe_2B_2 prepared by arc melting were compared with a sample containing impurities. Analysis was carried out by means of synchrotron X-ray diffraction, magnetic measurements and M?ssbauer spectroscopy. The analysis of synchrotron X-ray diffraction data confirmed the orthorhombic structure of space group Cmmm for AlFe_2B_2 with Al_(13)Fe_4 as main impurity phase. The magnetic measurements revealed an unsaturated ferromagnetic state in AlFe_2B_2 with a transition temperature(T_c) of 286 K. Isothermal magnetization measurment at 5 K gave a saturation magnetization of 0.7 μB per Fe atom while Arrott plots establish the second order nature of ferromagnetic transition. The thermal evolution of M?ssbauer spectra confirmed the ferromagnetic nature of this material revealing an hyperfine field of 73 kOe and an isomer shift of 0.46 mm/s at 100 K. The M?ssbauer spectra of a phase pure sample was compared with the one containing impurity phases. It is suggested that the low temperature paramagnetic contribution in M?ssbauer spectra of phase pure material may have its origin in some intrinsic phenomena arising from defects or inhomogeneities in crystal structure.     

Corrosion study of resorbable Ca60Mg15Zn25 bulk metallic glasses in physiological fluids

The corrosion activity of amorphous plates of Ca_(60)Mg_(15)Zn_(25)alloy was investigated.The biocompatible elements were selected for the alloy composition.The electrochemical corrosion and immersion tests were carried out in a multi-electrolyte fluid and Ringer's solution.Better corrosion behavior was observed for the samples tested in a multi-electrolyte fluid despite the active dissolution of Ca and Mg in Ringer's solution.The experimental results indicated that reducing concentration of NaCl from 8.6 g/dm~3for Ringer's solution to 5.75 g/dm~3caused the decrease of the corrosion rate.The volume of the hydrogen evolved after 480 min in Ringer's solution(40.1 ml/cm~2)was higher in comparison with that obtained in a multi-electrolyte fluid(24.4 ml/cm~2).The values of opencircuit potential(E_(OCP))for the Ca_(60)Mg_(15)Zn_(25)glass after 1 h incubation in Ringer's solution and a multielectrolyte fluid were determined to be-1553 and-1536 m V vs.a saturated calomel electrode(SCE).The electrochemical measurements indicated a shift of the corrosion current density(j_(corr))from 1062μA/cm~2for the sample tested in Ringer's solution to 788μA/cm~2for the specimen immersed in a multi-electrolyte fluid.The corrosion products analysis was conducted by using the X-ray photoelectron spectroscopy(XPS).The corrosion products were identified to be CaCO_3,Mg(OH)_2,CaO,MgO and Zn O.The mechanism of corrosion process was proposed and described based on the microscopic observations.The X-ray diffraction and Fourier transform infrared spectroscopy(FTIR)also indicated that Ca(OH)_2,CaCO_3,Zn(OH)_2and Ca(Zn(OH)_3)_2·2H_2O mainly formed on the surface of the studied alloy.