WCoB金属陶瓷的制备及其性能研究

以WC、TiB2、Co粉末为原料,采用真空液相反应烧结技术制备WCoB金属陶瓷,并利用XRD、SEM和EDS对其微观形貌及相组成进行了表征。结果表明,WCoB金属陶瓷由WCoB、W2CoB2、TiC、Co2B和TiB2等相组成,其硬度为HRA84.4～92.2,合金密度为9.3～10.2g/cm3。随着钴含量的增加,烧结后WCoB金属陶瓷的合金密度和硬度值均有所下降,较高的烧结温度有利于晶粒细化。磨损试验发现WCoB金属陶瓷的耐磨性优于YG8硬质合金。     

Effects of Cr and Mo elements on the microstructures and compressive properties of the in situ (TiC_xN_y–TiB_2)/Ni cermets

In-situ(TiC_xN_y–TiB_2)/Ni cermets with 70 wt%TiC_xN_y–TiB_2 were successfully fabricated by combustion synthesis and hot pressing sintering in Ni-Ti-B_4C-BN powder systems.The microstructures,density,compressive properties,and hardness of the TiC_xN_y–TiB_2/Ni cermets with the addition of 0–8 wt%Cr/Mo to the Ni-Ti-B_4C-BN powder systems were compared and analysed.The results showed that the ceramic particles distributed uniformly in the cermets,and the size of the ceramic particles reduced with the Cr/Mo addition.Both Cr and Mo addition can improve the hardness,compressive properties,and fracture strains of the cermets.The hardness,compressive strength,and fracture strain of the(TiC_xN_y–TiB_2)/(Ni+Cr)cermets increased from 1561 HV,2.94 GPa,and 2.9%to 1864 HV,3.65 GPa,and 3.4%,respectively when the Cr content increased to 5 wt%.The hardness and compressive strength of the(TiC_xN_y–TiB_2)/(Ni+Mo)cermets increased from 1561 HV and 2.94 GPa to 1902 HV and 3.43 GPa,respectively when the Mo content increased to 8 wt%.The cermets with Cr had better compressive properties than the cermets with Mo.     

Mo2 NiB2基金属陶瓷的制备与性能

采用单质硼粉、镍粉和钼粉结合反应硼化烧结法制备了Mo2 NiB2基金属陶瓷,研究了Mo2 NiB2基金属陶瓷在烧结过程中的物相转变和尺寸变化以及烧结温度和保温时间对其力学性能和显微组织的影响.结果发现：随着烧结温度升高,材料物相逐渐由单质相变为二元硼化物相和三元硼化物相,并且材料的尺寸先发生细微收缩,再在硼化反应过程中逐渐增加,最后在液相烧结过程中逐渐减小;随着烧结温度升高,Mo2 NiB2基金属陶瓷的抗弯强度和硬度先增加后减小,在1290℃达到最大,分别为1346.5 MPa和83.7 HRA,并且硬质相颗粒逐渐粗化;保温时间对材料性能的影响与烧结温度一致,但在保温30 min时抗弯强度最大(1453.3 MPa),保温60 min时硬度最大(83.7 HRA).     

添加C、Si元素对Mo_2FeB_2基金属陶瓷组织及力学性能的影响

采用真空液相反应烧结法制备Mo_2FeB_2基金属陶瓷,基于正交试验设计对金属陶瓷中C、Si添加量进行研究,选取抗弯强度和硬度为试验指标进行极差和方差分析,并借助OM、XRD、SEM、EDS等手段对金属陶瓷的物相组成和显微组织进行表征。结果表明,Si含量对Mo_2FeB_2基金属陶瓷硬度影响显著,而C含量对其抗弯强度影响显著。在烧结工艺条件相同时,添加0.5%C和0.5%Si的金属陶瓷试样具有最佳的综合力学性能,硬度和抗弯强度分别为HRA85.4和1970 MPa;此时,Mo_2FeB_2基金属陶瓷致密度高,硬质相颗粒细小且均匀地分布在Fe基黏结相中。     

Effect of boehmite sol on the crystallization behavior and densification of mullite formed from a sol–gel precursor

Hybrid mullite sol was synthesized from an aqueous solution of aluminum nitrate (AN), aluminum isopropoxide (AIP) and tetraethylorthosilicate (TEOS), doped with boehmite sol with different ratios. Pressureless sintering of the xerogel was carried out at different temperatures in the presence of boehmite doping. The xerogel and sintered powder were characterized by FTIR, TG-DSC, XRD, SEM and bulk density. The addition of boehmite caused the formation of metaphase spinel (6Al2O3·SiO2) crystal before the appearance of mullite phase, which could lead to the formation of amorphous phase and suppress the premature formation of mullite. Both of these effects improve the densification of mullite. A maximum density about 98% of the theoretical density (TD, 3.01 g/cm3 ) of mullite could be obtained for 5 wt% boehmite addition at 1200 1C pressureless sintering.     

Effect of Yb2O3 doping on the grain boundary of NiFe2O4–10NiO-based cermets after sintering

xYb2O3–15(20Ni–Cu)/(85?x)(NiFe2O4–10NiO) (x=0, 0.25, 0.5, 0.75, 1.0, 2.0, and 10.0) cermets for aluminum electrolysis were prepared to investigate the effect of Yb2O3 doping on the grain boundary of the cermets after sintering. The results showed that each interface was very clear and that with increasing Yb2O3 content, most of the Yb was evenly distributed at the grain boundary. Moreover, according to the phase composition and microstructural analysis by X-ray diffraction (XRD), scanning electron microscopy with energy dispersive X-ray spectroscopy (SEM/EDX), and electron probe microanalysis (EPMA), YbFeO3 was produced along the grain boundary. The YbFeO3 was concluded to not only have formed from the interaction between the NiFe2O4 or Fe2O3 component and Yb2O3 at the grain boundary of the cermets, but also from the decomposition of NiFe2O4 into NiO and Fe2O3 and the subsequent reaction of Fe2O3 with Yb2O3. Thus, the pro-duction of YbFeO3 resulted in a cermet with high relative density, good electrical conductivity, and good corrosion resistance.     

Microstructure and mechanical properties of spark plasma sintered Ti-Mo alloys for dental applications

Ti-Mo alloys with various Mo contents from 6wt% to 14wt% were processed by spark plasma sintering based on elemental powders. The influence of sintering temperature and Mo content on the microstructure and mechanical properties of the resulting alloys were investigated. For each Mo concentration, the optimum sintering temperature was determined, resulting in a fully dense and uniform microstructure of the alloy. The optimized sintering temperature gradually increases in the range of 1100–1300℃ with the increase in Mo content. The microstructure of the Ti-(6–12)Mo alloy consists of acicular α phase surrounded by equiaxed grains of β phase, while the Ti-14Mo alloy only contains single β phase. A small amount of fine α lath precipitated from β phase contributes to the improvement in strength and hardness of the alloys. Under the sintering condition at 1250℃, the Ti-12Mo alloy is found to possess superior mechanical properties with the Vickers hardness of Hv 472, the compressive yield strength of 2182 MPa, the compression rate of 32.7%, and the elastic modulus of 72.1 GPa. These results demonstrate that Ti-Mo alloys fabricated via spark plasma sintering are indeed a perspective candidate alloy for dental applications.     

Fabrication of solid-phase-sintered SiC-based composites with short carbon fibers

Solid-phase-sintered SiC-based composites with short carbon fibers (Csf/SSiC) in concentrations ranging from 0 to 10wt% were prepared by pressureless sintering at 2100°C. The phase composition, microstructure, density, and flexural strength of the composites with different Csf contents were investigated. SEM micrographs showed that the Csf distributed in the SSiC matrix homogeneously with some gaps at the fiber/matrix interfaces. The densities of the composites decreased with increasing Csf content. However, the bending strength first increased and then decreased with increasing Csf content, reaching a maximum value of 390 MPa at a Csf content of 5wt%, which was 60 MPa higher than that of SSiC because of the pull-out strengthening mechanism. Notably, Csf was graphitized and damaged during the sintering process because of the high temperature and reaction with boron derived from the sintering additive B₄C; this graphitization degraded the fiber strengthening effect.     

MnO2对8YSZ低温活化烧结及其性能的影响

以MnO2为8YSZ的烧结助剂,研究MnO2含量和烧结工艺参数对8YSZ活化烧结及其性能的影响.采用阿基米德排水法、维氏显微硬度仪、电子万能试验机对烧结块体的致密度、硬度和抗弯强度进行分析,并使用扫描电子显微镜(SEM)、X线衍射分析(XRD)对其微观形貌和相组成进行表征.实验结果表明:块体的致密度随着MnO2含量的增加而逐渐增加,当MnO2添加量为3％时获得了最好的烧结效果;随着温度的升高,块体致密度也逐渐增加,在1300℃烧结4h时,致密度达到了98.59％:在此条件下,样品的硬度与抗弯强度均为最佳,分别为1830.21(HV)与235.46 MPa.     

磁控共溅射法制备Zn_(1-x)Cr_xO薄膜及其结构性能

本文采用磁控共溅射方法在玻璃衬底上制备了Cr掺杂ZnO薄膜,通过改变Cr溅射功率,从而改变Cr的掺杂量.介绍了Zn1-xCrxO薄膜的制备方法,分别用X射线衍射(XRD)和X射线光电子能谱(XPS)对不同Cr溅射功率的一系列薄膜的结构,成份、元素含量及价态等性能进行了分析.结果表明,Cr溅射功率为20 W的样品,具有最好的c轴择优取向,Cr以+3价形式掺入薄膜中,Cr3+替代了部分Zn2+.     

反应键合B4C–SiC复合材料的组织和力学性能

Reaction-bonded B₄C–SiC composites are highly promising materials for numerous advanced technological applications. However, their microstructure evolution mechanism remains unclear. Herein, B₄C–SiC composites were fabricated through the Si-melt infiltration process. The influences of the sintering time and the B₄C content on the mechanical properties, microstructure, and phase evolution were investigated. X-ray diffraction results showed the presence of SiC, boron silicon, boron silicon carbide, and boron carbide. Scanning electron microscopy results showed that with the increase in the boron carbide content, the Si content decreased and the unreacted B₄C amount increased when the sintering temperature reached 1650°C and the sintering time reached 1 h. The unreacted B₄C diminished with increasing sintering time and temperature when B₄C content was lower than 35wt%. Further microstructure analysis showed a transition area between B₄C and Si, with the C content marginally higher than in the Si area. This indicates that after the silicon infiltration, the diffusion mechanism was the primary sintering mechanism of the composites. As the diffusion process progressed, the hardness increased. The maximum values of the Vickers hardness, flexural strength, and fracture toughness of the reaction-bonded B₄C–SiC ceramic composite with 12wt% B₄C content sintered at 1600°C for 0.5 h were about HV 2400, 330 MPa, and 5.2 MPa·m0.5, respectively.     

Porous SiC ceramics fabricated by quick freeze casting and solid state sintering

Porous SiC ceramics with uniform microstructure were fabricated by quick freezing in liquid nitrogen and solid state sintering.Poly(vinyl alcohol)(PVA) was added as binder and pore morphology controller in this work.The microstructure and mechanical properties of porous SiC ceramics could be controlled by the composition of the aqueous slurries.Both solid content of the slurries and PVA content impacted on the pore structures and mechanical properties of the porous SiC ceramics.The solid content of slurries and PVA content varied from 60 to 67.5 wt%and 2-6 wt%,respectively.Besides,the grain morphology of ceramics was also tailored by changing the sintering temperature from 2050 to 2150 ℃.Porous SiC ceramics with an average porosity of 42.72%,flexural strength of 59.28 MPa were obtained at 2150 ℃ from 67.5 wt% slurries with 2 wt% PVA.     

Sintering behaviors and consolidation mechanism of high-chromium vanadium and titanium magnetite fines

To achieve high efficiency utilization of high-chromium vanadium–titanium magnetite (V–Ti–Cr) fines, an investigation of V–Ti–Cr fines was conducted using a sinter pot. The chemical composition, particle parameters, and granulation of V–Ti–Cr mixtures were analyzed, and the effects of sintering parameters on the sintering behaviors were investigated. The results indicated that the optimum quicklime dosage, mixture moisture, wetting time, and granulation time for V–Ti–Cr fines are 5wt%, 7.5wt%, 10 min, and 5–8 min, respectively. Meanwhile, the vertical sintering speed, yield, tumbler strength, and productivity gains were shown to be 21.28 mm/min, 60.50wt%, 58.26wt%, and 1.36 t·m-2·h-1, respectively. Furthermore, the consolidation mechanism of V–Ti–Cr fines was clarified, revealing that the consolidation of a V–Ti–Cr sinter requires an approximately 14vol% calcium ferrite liquid-state, an approximately 15vol% silicate liquid-state, a solid-state reaction, and the recrystallization of magnetite. Compared to an ordinary sinter, calcium ferrite content in a V–Ti–Cr sinter is lower, while the perovskite content is higher, possibly resulting in unsatisfactory sinter outcomes.     

Cr含量对高锰奥氏体TWIP钢高温氧化行为的影响

通过恒温氧化增重实验和扫描电镜观察及XRD分析,研究了Cr含量对高锰奥氏体孪晶诱发塑性(TWIP)钢在700℃氧化8 h的高温氧化动力学过程及氧化产物的影响.结果表明:随着Cr含量的提高,高锰奥氏体TWIP钢的抗氧化能力增强;当Cr的质量分数为1.13%时,经过在700℃下8 h的高温氧化,样品单位面积的氧化增重为30μg/mm2;而当Cr的质量分数增加到3.95%时,单位面积的氧化增重降低至3μg/mm2.随着Cr含量的增加,高锰奥氏体TWIP钢氧化层的致密度提高,氧化产物的构成也具有明显的差异.     

Zr^4＋对KTP晶体结构畸变性的影响

采用高温固相反应法合成了掺杂Zr^4＋的KTP晶体。用XRD对烧成产品的物相进行了系统的分析，用最小二乘法对样品的晶胞参数进行了计算，系统分析了掺Zr^4＋对晶胞参数的影响。随着掺杂Zr^4＋浓度的增加，晶胞参数明显增大，KTP中八面体畸变的程度会更高。     

聚氨酯弹性体电致伸缩特性

为了提高材料的电致伸缩特性,通过原位共聚合法在聚氨酯弹性体(PUE)中掺入了不同质量比例的纳米钛酸钡.采用LCR测试仪、邵氏硬度计和电容法电致伸缩特性测试装置研究了纳米钛酸钡掺杂对PUE的影响.试验结果表明:随着掺杂比例的提高,PUE的介电系数和硬度增加,回复速度变差;较低的掺杂能提高PUE的电致伸缩应变,过高的掺杂导致PUE电致伸缩特性下降,掺杂6%钛酸钡的PUE表现出最佳电致伸缩应变.进一步对PUE电致伸缩特性因素进行了理论分析并提出了电致伸缩弹性体电荷迁移逾渗模型,其很好地解释了电致伸缩材料弯曲、临界电场反转膨胀、高掺杂回弹等现象.     

B4C-TiB2-SiC复合陶瓷的SPS制备及组织性能研究

针对B₄C陶瓷烧结性能较差、成本较高的技术问题,提出了一种新型的B₄C基复合陶瓷的制备方法. 该方法以B₄C、Ti₃SiC₂及Si的混合粉作为初始粉体,通过放电等离子烧结技术（SPS）制备第二相（TiB₂+SiC）质量分数为30%的B₄C-TiB₂-SiC复合陶瓷,利用SPS特殊的烧结机制以及烧结过程中的原位放热反应,有效提升了B₄C陶瓷的烧结性能,降低了B₄C陶瓷的制造成本. 研究结果表明,在烧结温度为1650 °C,保温时间为5 min,烧结压力为50 MPa的条件下,制备得到了具有较高致密度（98.5%）的B₄C-TiB₂-SiC复合陶瓷. 随着烧结压力的增加,B₄C-TiB₂-SiC复合陶瓷的硬度逐渐增大,断裂韧性不断减小,而复合陶瓷的弯曲强度则呈现出先缓慢增加后迅速增大的变化趋势.      

高硼多组分铸铁的组织及相元素分布

这种新提出的新型铸铁的化学成分为在0.7C–5W–5Mo–5V–10Cr–2.5Ti (wt%)中分别添加1.6wt% B和2.7wt% B。这项工作的目的是研究硼的含量对合金的结构状态和阶段元素分布对耐磨结构成分的形成影响。结果表明,当B含量为1.6wt%时,合金由三种共晶组成:(a) “M₂(C,B)₅+铁素体”具有“汉字”形貌 (89.8vol%), (b) “M₇(CB)₃+奥氏体”具有“莲座”形貌,(c) “M₃C+奥氏体”具有“莱氏体”形貌 (2.7vol%)。当硼含量为2.7wt%时,基体硬度由HRC 31提高到HRC 38.5。组织中出现了平均显微硬度为HV 2797的初生碳化物M₂(C,B)₅,体积分数为17.6vol%。共晶体(a)和(b,c)的体积分数分别降低到71.2vol%和3.9vol%。基体为“铁素体/奥氏体” (1.6wt% B) 和“铁素体/珠光体”(2.7wt% B),两种铸铁均含有致密析出碳化物(Ti,M)C和碳硼化物(Ti,M)(C,В),体积分数为7.3%–7.5%。基于能量色散X射线能谱,给出了元素相的分布和相应的相公式。     

Ti(C,N)基金属陶瓷烧结性能及其组织的研究

研究了温度与碳含量对Ｔｉ（Ｃ，Ｎ）基金属陶瓷烧结性能及组织的影响，研究结果表明：材料的抗弯强度对烧结温度最敏感，而密度、硬度、平均线收缩系数对烧结温度的敏感性依次递减；材料中碳粉含量增加时，会使其烧结温度明显降低，当添加量为２．２％时，金属陶瓷组织中会出现石墨相，使材料的抗弯强度下降．     

烧结温度对铜基粉末冶金摩擦材料性能的影响

为了探究烧结温度对铜基粉末冶金摩擦材料性能的影响,通过四种温度(825、850、875、900 ℃)热压烧结,成功制备了铜基粉末冶金摩擦材料。研究了材料的微观组织、密度、硬度、抗压强度、摩擦性能,由此得到材料的较佳烧结温度。结果表明,在四种烧结温度下,材 料中的各元素能均匀地分布在Cu基体中。随着烧结温度的升高,密度、硬度、抗压强度和摩擦因数都先增大后减小,而孔隙率和磨损量先减小后增大。Cr能改善Cu与C之间的湿润性,提高金属基体与非金属组元之间的结合强度,从而使材料的密度增大;Ni、Mn能向Cu中扩散,形成固溶体,阻碍位错运动,提高材料的硬度。铜基粉末冶金摩擦材料较佳烧结温度为850 ℃,此时的密度为6.17 g/cm³,孔隙率为8.62%,维氏硬度为81.2,抗压强度为172.8 MPa,摩擦因数为0.37,磨损量为0.074 g。