首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到19条相似文献,搜索用时 203 毫秒
1.
Occurrence of perfluoroalkyl acids in precipitation from Shenyang, China   总被引:2,自引:0,他引:2  
Perfluorosulfonates (PFSAs) and perfluorocarboxylates (PFCAs) in precipitation collected from Shenyang, China were determined. Snow samples were collected in the snow event on March 4, 2007 from 34 sites involving both the urban and suburban areas in Shenyang. The snowmelt was preconcentrated by solid phase extraction and analyzed using LC-MS method. Measurable amounts of perfluoroalkyl acids (PFAS) were found in precipitation samples from Shenyang, demonstrating that wet deposition is one possible pathway for the removing of the selected PFAS chemicals from atmosphere. Major PFAS detected were PFOS (〈0.38-51 ng/L), PFOA (0.82-13 ng/L) and PFHpA (0.76-11 ng/L), with their mean concentration of 5.4, 3.3 and 2.9 ng/L, respectively. Other PFSAs and PFCAs were detected at much lower frequency or below the limit of detection in all the samples. The work presented here offers some basis for the investigation on the environmental behavior and the evaluation of human exposure to PFAS.  相似文献   

2.
Aluminium laurate [Al(OOCC11H23)3] was synthesized as a surfactant, which can dissolve in micellar solution of a zwitterionic surfactant, tetradecycldimethylamine oxide (C14DMAO). The phase behavior of the mixtures of Al(OOCC11H23)3 and C14DMAO in water was studied and birefringent Lα-phase was observed. The birefringent Lα-phase consists of vesicles that were demonstrated by Polarizer and Transmission Electron Microscope (TEM) micrographs. Al3 -coordinated vesicles could be used as templating-precursor, providing a vesicle-route for preparation of inorganic nanoscale particles.  相似文献   

3.
Autoigniting synthesis of gel from Ba(NO3)2, TiO(NO3)2 and C6H8O7H2O aqueous solution was investigated at an initial temperature of 600℃ and tetragonal BaTiO3 nanopowder with particle size of 80nm was prepared. It is indicated that the specific surface area of the combustion product before and after calcination is 14.74 m2/g and 12.49 m2/g, respectively. The combustion wave is composed of solid phase reaction zone and gaseous phase flame reaction zone. The combustion flametemperature is 1 123 K derived from thermocouple measurement. The characteristics and densification behavior of the sol-gel autoigniting synthesized BaTiO3 nanopowder were investigated.  相似文献   

4.
Cationic gemini surfactant dimethylene-1,2-bis(dodecyldiethylammonium bromide), referred to as C12C2C12(Et) was synthesized, and its surface property and aggregation behavior in aqueous solution were studied. The value of γ at the critical micelle concentration (γcmc) is much smaller than that of the surfactant homologues with longer spacer. Spherical and elongated micelles were formed in the aqueous solution of this gemini surfactant,and the spherical micelles were absolutely dominant compared to the elongated micelles at our studied concentration quantitatively.  相似文献   

5.
A novel method for recovering zinc from zinc ferrite by reduction roasting–ammonia leaching was studied in this paper. The reduction thermodynamic of zinc ferrite by CO was analyzed. The effects of roasting parameters on the phase transformation and conversion rate of zinc ferrite, and the leaching behavior of zinc from the reductive roasted samples by ammonia leaching, were experimentally investigated. The mineralogical phase compositions and chemical compositions of the samples were characterized by X-ray diffraction and chemical titration methods, respectively. The results showed that most of the zinc ferrite was transformed to zinc oxide and magnetite after weak reduction roasting. 86.43% of the zinc ferrite was transformed to zinc oxide under the optimum conditions: CO partial pressure of 25%, roasting temperature of 750°C, and roasting duration of 45 min. Finally, under the optimal leaching conditions, 78.12% of zinc was leached into the solution from the roasted zinc ferrite while all iron-bearing materials were kept in the leaching residue. The leaching conditions are listed as follows: leaching duration of 90 min, ammonia solution with 6 mol/L concentration, leaching temperature of 50°C, solid-to-liquid ratio of 40 g/L, and stirring speed of 200 r/min.  相似文献   

6.
In this paper, we report the growth and characteristics of titania nanotube arrays prepared by anodic oxidation and then annealed in an oxygen atmosphere at 500℃. The titania nanotube arrays presented high sensitivity to hydrogen gas. The crystalline phase of the samples was checked by X-ray diffraction (XRD). The differences in the nanotubes morphology attributed to the etched samples due to anodization potential, reaction time and the electrolyte concentration were analyzed by scanning electron mi- croscopy (SEM). The gas sensitive parameters of the samples were obtained from resistance, the response time and the recovery time at different temperatures.  相似文献   

7.
Three reaction systems of MoS2-Fe, FeS-Fe, and FeS-Fe-Mo were designed to investigate the use of FeS as an alternative to MoS2 for producing Fe-based friction materials. Samples were prepared by powder metallurgy, and their phase compositions, microstructures, mechanical properties, and friction performance were characterized. The results showed that MoS2 reacts with the matrix to produce iron-sulfides and Mo when sintered at 1050℃. Iron-sulfides produced in the MoS2-Fe system were distributed uniformly and continuously in the matrix, leading to optimal mechanical properties and the lowest coefficient of friction among the systems studied. The lubricity observed was hypothesized to originate from the iron-sulfides produced. The FeS-Fe-Mo system showed a phase composition, porosity, and density similar to those of the MoS2-Fe system, but an uneven distribution of iron-sulfides and Mo in this system resulted in less-optimal mechanical properties. Finally, the FeS-Fe system showed the poorest mechanical properties among the systems studied because of the lack of Mo reinforcement. In friction tests, the formation of a sulfide layer contributed to a decrease in coefficient of friction (COF) in all of the samples.  相似文献   

8.
A novel method for recovering zinc from zinc ferrite by reduction roasting–ammonia leaching was studied in this paper. The reduction thermodynamic of zinc ferrite by CO was analyzed. The effects of roasting parameters on the phase transformation and conversion rate of zinc ferrite, and the leaching behavior of zinc from the reductive roasted samples by ammonia leaching, were experimentally investigated. The mineralogical phase compositions and chemical compositions of the samples were characterized by X-ray diffraction and chemical titration methods, respectively. The results showed that most of the zinc ferrite was transformed to zinc oxide and magnetite after weak reduction roasting. 86.43% of the zinc ferrite was transformed to zinc oxide under the optimum conditions: CO partial pressure of 25%, roasting temperature of 750°C, and roasting duration of 45 min. Finally, under the optimal leaching conditions, 78.12% of zinc was leached into the solution from the roasted zinc ferrite while all iron-bearing materials were kept in the leaching residue. The leaching conditions are listed as follows: leaching duration of 90 min,ammonia solution with 6 mol/L concentration, leaching temperature of 50°C, solid-to-liquid ratio of 40 g/L, and stirring speed of 200 r/min.  相似文献   

9.
This study addresses the liquid-liquid extraction behavior of phosphorus from a sulfuric acid solution using benzyl dimethyl amine(BDMA)in kerosene.The extraction equilibria investigated with varied BDMA concentrations could reveal the formation of 3[BDMA]·[H3PO4]-complex in the organic phase.The thermodynamic properties determined at various temperatures indicated that the process was exothermic with a calculated enthalpy(△HΘ)of?24.0 kJ·mol?1.The organic-to-aqueous phase(O/A)volume ratio was varied to elucidate the quantitative extraction of phosphorus.The McCabe-Thiele diagram plotted for the extraction isotherm was validated for the requirement of three counter-current stages in the extraction at an O/A volume ratio of 2.0/3.5.The back-extraction of phosphorus from the loaded organic phase was quantitatively achieved by contacting 4.0 mol·L?1 H2SO4 solution in three stages of counter-current contact at an O/A volume ratio of 3/2.This study can be applied to remove phosphorus from the sulfuric acid leach solutions of monazite processing,and many other solutions.  相似文献   

10.
Viscosities of uranium solutions in H2O and 3mol/L HNO3 medium were measured by Ubbelhode flow viscometer in the concentration range of 0.5%-3.0% from 10℃ to 30℃ at 5℃ interval.Viscosity data were interpreted in terms of an empirical equation;η=aoexp(boM coM^2).Values of coefficients ao, bo and Co were calculated for all the three systems studied. Flow activation energies and thermodynamic parameters were also evaluated.  相似文献   

11.
The effect of Na+ ion concentration on the crystalline phase composition and morphology of xonotlite crystals prepared in a CaO-SiO2-H2O system via hydrothermal synthesis was analyzed. X-ray diffraction (XRD) and scanning electron microscopy (SEM) results indicate that Na+ ion concentration has a significant impact on the composition and morphology of crystalline phases in the products under the initial conditions of a molar ratio of CaO/SiO2 of 1.0 and a reactant concentration of 0.05 mol·L?1 at 225°C for 15 h. The main crystalline phase in the products has a phase transition from xonotlite to pectolite, and the morphology changes from fibrous to broomlike shape with the Na+ ion concentration increasing. Therefore, the content of Na2O in the raw material should be less than 5wt% for preparing pure xonotlite crystals via hydrothermal synthesis in a CaO-SiO2-H2O system.  相似文献   

12.
High-reproducibility silicalite-1 membranes were synthesized on silica tubes by in-situ hydrothermal synthesis, and the relative standard deviation (R.S.D.) of average separation factor for eight membranes was only 7.5%. By using an effective method called "solution-filling (SF)", the average flux of membranes prepared with SF method was improved by about 49% compared to membranes prepared without SF method, and the highest flux of membrane prepared with SF method towards ethanol/H2O mixture at 80℃ was 1.49 kg/(m^2·h). Pervaporation experiments showed that the fluxes of silicalite-1 membranes at 60℃ were 2.63, 0.87, 0.24, and 0.20 kg/(m^2·h) towards methanol/H2O, ethanol/H=O, 2-propanol/H2O, and 1-propanol/H2O mixtures, respectively, and the corresponding separation factors were 22, 69, 81, and 159, respectively.  相似文献   

13.
Cu-P-silicon carbide (SiC) composite coatings were deposited by means of electroless plating. The effects of pH values, temperature, and different concentrations of sodium hypophosphite (NaH2PO2·H2O), nickel sulfate (NiSO4·6H2O), sodium citrate (C6H5Na3O7·2H2O) and SiC on the deposition rate and coating compositions were evaluated, and the bath formulation for Cu-P-SiC composite coatings was optimised. The coating compositions were determined using energy-dispersive X-ray analysis (EDX). The corresponding optimal operating parameters for depositing Cu-P-SiC are as follows: pH 9; temperature, 90°C; NaH2PO2·H2O concentration, 125 g/L; NiSO4·6H2O concentration, 3.125 g/L; SiC concentration, 5 g/L; and C6H5Na3O7·2H2O concentration, 50 g/L. The surface morphology of the coatings analysed by scanning electron microscopy (SEM) shows that Cu particles are uniformly distributed. The hardness and wear resistance of Cu-P composite coatings are improved with the addition of SiC particles and increase with the increase of SiC content.  相似文献   

14.
A 1040℃-hot-deformed Ti2AlNb-based alloy solution-treated at 950℃ and aged at different temperatures was quantitatively investigated. The microstructure, size of the phase, and microhardness of the deformed alloys were measured. The results indicated that the microstructure of the deformed Ti2AlNb-based alloy specimens comprise coarse O lath, fine O lath, equiaxed O/α2, and acicular O phase. More O phase was generated in the deformed alloy after heat treatment because the acicular O phase was more likely to nucleate and grow along the deformation-induced crystal defects such as dislocations and subgrain boundaries. After deformation and subsequent heat treatment, the acicular O phase of the resultant alloy became finer compared to that of the undeformed alloy, and the acicular O phase became coarser and longer with the elevated aging temperature, while the width of the O lath exhibited unobvious variations. The hot deformation facilitated the dissolution of the O lath but accelerated the precipitation of the acicular O phase. When the 950℃-solution-treated deformed Ti2AlNb-based alloy was then aged at 750℃ for different periods, the phase content was nearly invariable, O and B2 phases eventually reached equilibrium, and the microstructure became stable and homogeneous.  相似文献   

15.
The solubility properties of ZnCl\-2/ZnAc\-2/ZnSO\-4_Met_H\-2O systems at 25℃ in the whole cocentration range have been investigated by phase equilibrium method. The results indicate that ZnAc\-2 and ZnSO\-4 systems are both simple systems, which do not exist any compound; there are 2 complexes formed in ZnCl\-2 system: Zn(Met)Cl\-2 and Zn(Met)\-2Cl\-2·2H\-2O. Under the direction of phase equilibrium result, 2 solid complexes have been prepared in water and characterized by chemical analysis, IR, X_ray diffraction. Their combustion energies have also been determined by means of a RBC_type_1 rotating_bomb calorimeter, and their standard enthalpies of formation, Δ f, coor(s)H O-, have been calculated which are (-828.32±3.00) kJ·mol -1 and (-1 117.08±6.15) kJ·mol -1, respectively.  相似文献   

16.
A novel hydrothermal process was developed to extract zinc from pure zinc ferrite (ZnFe2O4) nanopowder and zinc-containing electric arc furnace (EAF) dust using hexahydrated ferric chloride (FeCl3·6H2O) as a decomposing agent. The effects of solid FeCl3·6H2O to ZnFe2O4 ratio by mass (RF/Z), hydrothermal reaction temperature, and time on zinc extraction were systematically investigated. In the results, when the hydrothermal reaction is conducted at 150℃ for 2 h with RF/Z of 15:20, the efficiency of zinc extraction from ZnFe2O4 reaches 97.2%, and the concentration of ferric ions (Fe3+) in the leaching solution is nearly zero, indicating a high selectivity for zinc. In addition, the zinc extraction efficiency from the EAF dust reaches 94.5% in the case of the hydrothermal reaction performed at 200℃ for 10 h with the solid FeCl3·6H2O to EAF dust ratio by mass (RF/EAF dust) of 15:10. Zinc and iron separation is achieved by adjusting the pH value of the leaching solution according to the different precipitation pH values of metal hydroxides.  相似文献   

17.
The dissolution rate of naked Al sheet in the acidic solutions containing polybutadienoic acid (PBA) with pH value of 0.3∼3.0 at 20∼60°C has been determined by electrometry and gravimetry methods. The form of electroactive Al(III) ions occurred on the anode and the behavior of electrocoagulation of PBA have been approached. The results indicate that the superior condition of electrocoagulation of water-soluble nonsaturable low polymer PBA is the adoption of the electroactive Al(III) ions occurred in electrolyte containing 1.0 g·L−1 PBA+0.2 mol·L−1C6H8O7 citric acid with pH value of 3.0 at 30°C. The mechanism of corrosion-inhibited or electrocoagulation resulted from the electroactive Al(III) ions coordinate-COOH group of PBA and free ions of citric groups into the aluminum soaps with bicyclic structure are briefly discussed in this paper. Supported by the National Natural Science Foundation of China Tao Yingchu: born in 1943, Professor  相似文献   

18.
The microstructure and room-temperature tensile properties of Ti14, a new α+Ti2Cu alloy, were investigated after conventional forging at 950°C and semi-solid forging at 1000 and 1050°C, respectively. Results show that coarse grains and grain boundaries are obtained in the semi-solid alloys. The coarse grain boundaries are attributed to Ti2Cu phase precipitations occurred on the grain boundaries during the solidification. It is found that more Ti2Cu phase precipitates on the grain boundaries at a higher semi-solid forging temperature, which forms precipitated zones and coarsens the grain boundaries. Tensile tests exhibit high strength and low ductility for the semi-solid forged alloys, especially after forging at 1000°C. Fracture analysis reveals the evidence of ductile failure mechanisms for the conventional forged alloy and cleavage fracture mechanisms for the alloy after semi-solid forging at 1050°C.  相似文献   

19.
The Er3 doped Al2O3 powders were prepared by the sol-gel method using the aluminium isopropoxide [Al(OC3H7)3]-derived Al2O3 sols with addition of the erbium nitrate [Er(NO3)3.5H2O]. The different phase structure, including three crystalline types of (Al,Er)2O3 phases, γ, θ, α, and two Er-Al-O phases, ErAlO3 and Al10Er6O24, was obtained with the 1 mol% Er3 doped Al2O3 powders at the different sintering temperatures of 600―1200℃. The green and red up-conversion emissions centered at about 523, 545 and 660 nm, corresponding respectively to the 2H11/2, 4S3/2→4I15/2 and 4F9/2→4I15/2 transitions of Er3 , were detected by a 978 nm semiconductor laser diodes excitation. The phase structure and OH content had evident influence on the up-conversion emissions intensity. The maximum intensities of both the green and red emissions were obtained respectively for the Er3 doped Al2O3 powders sintered at 1200 ℃, which was composed mainly of α-(Al,Er)2O3, less of ErAlO3 and Al10Er6O24 phases, and with the least OH content. The two-photon absorption up-conversion process was involved in the green and red up-conversion emissions of the Er3 doped Al2O3 powders.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号