Relationship between lattice mismatch and ionic conduction of grain boundary in YSZ

The grain boundary plays an important role in the electrical behaviors of solid oxide electrolytes for solid state fuel cells. To reveal the relationship between the structure and the ionic conductivity of grain boundary,the conductive properties of {1 1 1} and {1 1 0} twist grain boundaries in 8 mol% yttria-stabilized zirconia have been examined. These boundaries have a series of Σ values defined by the coincident site lattice model. It has been found that the activation energy of {1 1 1} twist grain boundary increases and then decreases with the Σ value,while that of the {1 1 0} boundary shows an opposite trend. It is suggested that the properties can reflect the balance of the effects of lattice mismatch on the diffusion ability of oxygen vacancies and the segregation of oxygen vacancies and Y3 tions. Therefore,the properties in polycrystalline electrolyte can be adjusted by controlling the grain boundary structures.     

A.C. conductivity and relaxation dynamics in zinc–borate glasses

The frequency-dependent dielectric dispersion of ZnO–Na2O–Al2O3–B2O3(in mol%) glass prepared by the melt quenching technique is investigated in the temperatur e ranges from room temperature to 420 K. Dielectric relaxation has been analyzed based on the behavior of electric modulus behavior. An analysis of the real and imaginary parts of dielectric is performed assuming the ideal Debye behavior as confirmed by Cole–Cole plot. The activation energy associated with the dielectric relaxation determined from the electric modulus spectra was found to be 1.863 eV, which is close to that the activation energy for d.c. conductivity (1.871 eV), indicating the similar nature of relaxation and conductivity.     

The enhanced corrosion resistance of UMAO coatings on Mg by silane treatment

The surface silanization was carried out on ultrasonic micro-arc oxidation(UMAO) coatings on pure magnesium using KH550 as silane coupling agent(SCA). The surface morphology, chemical bonds and corrosion resistance of the silane films were investigated by scanning electron microscope(SEM), Fourier transform infrared spectroscopy(FTIR) and electrochemical workstation, respectively. The results showed that hybrid coatings were successfully prepared on pure magnesium by UMAO-Na OH(1 mol/L, 2 mol/L, 3 mol/L)-SCA processing. The organic films with Si–O–Mg bonds are helpful for the reduction of the pores in UMAO coatings. The pores decreased with increasing Na OH concentration. Compared with single UMAO treatment, the corrosion potentials(Ecorr) of magnesium plates with UMAO-Na OH(1 mol/L,2 mol/L, 3 mol/L)-SCA treatment increased by 29 m V, 53 m V and 75 m V, respectively, meanwhile the corrosion current density(Icorr) reduced one to two orders of magnitude. It indicated that the corrosion resistance of the coatings was improved by silane treatment.     

Effect of CuO addition on the sintering temperature and microwave dielectric properties of CaSiO3– Al2O3 ceramics

CuO-doped CaSiO3–1 wt% Al2O3 ceramics were synthesized via a traditional solid-state reaction method, and their sintering behavior,microstructure and microwave dielectric properties were investigated. The results showed that appropriate CuO addition could accelerate the sintering process and assist the densification of CaSiO3–1 wt% Al2O3 ceramics, which could effectively lower the densification temperature from1250 1C to 1050 1C. However, the addition of CuO undermined the microwave dielectric properties. The optimal amount of CuO addition was found to be 0.8 wt%, and the derived CaSiO3–Al2O3ceramic sintered at 1100 1C presented good microwave dielectric properties of εr?7.27,Q f?16,850 GHz and τf? 39.53 ppm/1C, which is much better than those of pure CaSiO3 ceramic sintered at 1340oC(Q f?13,109 GHz).The chemical compatibility of the above ceramic with 30 Pd/70 Ag during the cofiring process has also been investigated, and the result showed that there was no chemical reaction between palladium–silver alloys and ceramics.& 2014 Chinese Materials Research Society. Production and hosting by Elsevier B.V. All rights reserved.     

Core loss analysis of Finemet type nanocrystalline alloy ribbon with different thickness

Nanocrystalline soft magnetic materials are widely used in power electronic applications due to their high permeability,magnetization and low core loss.In this paper,Fe_(73.5)Cu_1Nb_3Si_(15.5)B_7(at%)nanocrystalline alloy ribbons,with ultra-thin thickness of 14μm,and also 18 and 22μm,were prepared by a planar flow casting method with a single roller device.Soft magnetic properties of these ribbons were analyzed after nanocrystallization annealing.The experiments were conducted on toroidal samples using IWATSU B-H Analyzer over a frequency range of 10–100 kHz,at induction amplitudes of 100–500 m T,at room temperature.It was found that the excess eddy current loss P_(ex)was the dominant factor in the overall core loss above 10 k Hz.The toroidal samples made of the 14μm thickness ribbon exhibit very low total core loss of 48 W/kg at a frequency of100 kHz and magnetic flux density of 300 mT.The ratio of the P_(ex)was up to 89%at 100 kHz.The ribbon with lower thickness exhibits lower P_(ex)and therefore lower total core loss.The domain structure evidences were found.It indicates that the ribbons with small thickness are preferable for application in high frequency condition.     

Microstructure and growth kinetics of Ce and Y jointly modified silicide coatings for Nb–Ti–Si based ultrahigh temperature alloy

In order to protect Nb-Ti-Si based ultrahigh temperature alloy from oxidation, pack cementation processes were utilized to prepare Ce and Y jointly modified silicide coatings. The Ce and Y jointly modified silicide coating has a double-layer structure: a relatively thick (Nb, X)Si2 (X represents Ti, Cr and Hf elements) outer layer and a thin (Ti, Nb)5Si4 transitional layer. The pack cementation experiments at 1150 ℃ for 8 h proved that the addition of certain amounts of CeO2 and Y2O3 powders in the packs distinctly influenced the coating thickness, the contents of Si, Ce and Y in the (Nb, X)Si2 outer layers, and the density of cavities in the coatings. In order to study the effects of Ce and Y joint modification in the silicide coatings, both only Ce and only Y modified silicide coatings were also prepared for comparison. The mechanisms of the beneficial effects of Ce and Y are discussed. A pack mixture containing 1.5CeO2-0.75Y2O3 (wt%) powders was employed to investigate the growth kinetics of the Ce and Y jointly modified silicide coating at 1050, 1150 and 1250 ℃. It has been found that the growth kinetics obeyed parabolic laws and the parabolic rate constants were 109.20 mm2/h at 1050 ℃, 366.75 mm2/h at 1150 ℃ and 569.78 mm2/h at 1250 ℃, and the activation energy for the growth of the Ce and Y jointly modified silicide coating was 197.53 kJ/mol.     

The precipitation strengthening behavior of Cu-rich phase in Nb contained advanced Fe–Cr–Ni type austenitic heat resistant steel for USC power plant application

Copper has been used as a strengthening element in newly developed Fe–Cr–Ni type austenitic heat resistant steel for inducing Cu-rich phase precipitation to meet high temperature strength requirement for 60°C Ultra Super-Critical (USC) coal fired power plants for many years. However, the precipitation behavior and strengthening mechanism of Cu-rich phase in these advanced austenitic heat resistant steels is still unclear. In order to understand the precipitation strengthening behavior of Cu-rich phase and to promote high strength austenitic heat resistant steel development, 18Cr9 NiCuNb steel which is a Cu-added Nb contained advanced Fe–Cr–Ni type austenitic heat resistant steel has been selected for this study to be aged at 650°C till to 10,000 h. Micro-hardness and room temperature tensile test were conducted after long-time aging. SEM,TEM, HRTEM and three dimensional atom probe (3DAP) technology accompanying with thermodynamic calculation have been used to investigate the Cu-rich phase precipitation behavior during 650°C aging. The experimental results showed that Cu atoms can quickly concentrate in clusters at very early precipitation stage to form the fine nano-size Cu-rich ‘‘segregation areas’within less than 1 h at 650°C. With increasing aging time at 650°C Cu atoms continuously concentrate to Cu-rich segregation areas (clusters) and simultaneously other kinds of atoms such as Fe, Cr and Ni diffuse away from Cu-rich segregation areas to austenitic matrix, and finally to complete the transformation from Cu-rich segregation areas to Cu-rich phase. However, there is only Cu atoms concentration but not crystallographic transformation from early stage of Cu-rich clusters forming to the final Cu-rich phase formation. Even the Cu atom becomes the main composed element after 500 h aging at 650°C the Cu-rich phase still keeps coherent relationship with austenitic matrix. According the experimental results in this study, Cu-rich phase precipitation sequence which starts from the Cu atom segregation followed by the Cu diffusing from matrix to segregation areas and Fe, Cr and Ni atoms diffuse out from Cu-rich areas to matrix without crystallographic transformation is proposed. The Cu-rich phase is the most dispersed phase and contributes the most important strengthening effect among all precipitated phases (M23C6, MX and Cu-rich phase). It has been found that Cu-rich phase is very stable and still keeps in nano-size even for 10,000 h aging at 650°C. The unique precipitation strengthening of Cu-rich phase in combination with nano-size Nb-rich MX phase and grain-boundary M23C6carbide contributes excellent strengthening effect to 18Cr9 NiCuNb austenitic heat resistant steel.     

Activated carbon derived from rice husk by NaOH activation and its application in supercapacitor

Four activated carbon(AC) samples prepared from rice husk under different activation temperatures have been characterized by N2adsorption–desorption isotherms, thermogravimetric analysis(TGA–DTA), Fourier transform infrared spectroscopy(FTIR) and scanning electron microscopy(SEM). The specific surface area of AC sample reached 2681 m2 g 1under activation temperature of 800 1C. The AC samples were then tested as electrode material; the specific capacitance of the as-prepared activated carbon electrode was found to be 172.3 F g 1using cyclic voltammetry at a scan rate of 5 mV s 1and 198.4 F g 1at current density 1000 mA g 1in the charge/discharge mode.& 2014 Chinese Materials Research Society. Production and hosting by Elsevier B.V. All rights reserved.     

Effect of pickling processes on the microstructure and properties of electroless Ni–P coating on Mg–7.5Li–2Zn–1Y alloy

The electroless plating Ni–P is prepared on the surface of Mg–7.5Li–2Zn–1Y alloys with different pickling processes.The microstructure and properties of Ni–P coating are investigated.The results show that the Ni–P coatings deposited using the different pickling processes have a different high phosphorus content amorphous Ni–P solid solution structure,and the Ni–P coatings exhibit higher hardness.There is higher phosphorus content of Ni–P amorphous coating using 125 g/L Cr O3and 110 ml/L HNO3(w68%)than using 180 g/L Cr O3and 1 g/L KF during pre-treatment,and the coating structure is more compact,and the Ni–P coatings exhibit more excellent adhesion with substrate(Fcup to22 N).The corrosion potential of Ni–P coating is improved and exhibits good corrosion resistance.As a result,Mg-7.5Li-2Zn-1Y alloy is remarkably protected by the Ni–P coating.     

Microstructure and oxidation resistance of SiC–MoSi2 multi-phase coating for SiC coated C/C composites

In order to improve the anti-oxidation of C/C composites, a SiC–MoSi2multi-phase coating for SiC coated carbon/carbon composites(C/C)was prepared by low pressure chemical vapor deposition(LPCVD) using methyltrichlorosilane(MTS) as precursor, combined with slurry painting from MoSi2 powder. The phase composition and morphology were analyzed by scanning electron microscope(SEM) and X-ray diffraction(XRD) methods, and the deposition mechanism was discussed. The isothermal oxidation and thermal shock resistance were investigated in a furnace containing air environment at 1500 1C. The results show that the as-prepared SiC–MoSi2coating consists of MoSi2 particles as a dispersing phase and CVD–SiC as a continuous phase. The weight loss of the coated samples is 1.51% after oxidation at 1500 1C for 90 h, and 4.79% after 30 thermal cycles between 1500 1C and room temperature. The penetrable cracks and cavities in the coating served as the diffusion channel of oxygen, resulted in the oxidation of C/C composites, and led to the weight loss in oxidation.     

A simulation study on the thermal and wetting behavior of alkane thiol SAM on gold (111) surface

Molecular dynamics simulations have been performed to investigate the structural,thermal and wetting properties of self-assembled monolayer(SAM) of alkane thiol on gold surface.The specific heat capacity of the gold SAM surface was found to linearly increase with the temperature in the range 100–300 K.It was found to drop down at 400 K and this decrease might be attributed to the disorder of the SAM chains.Hydration of gold SAM surface for two different terminal groups,namely methyl(hydrophobic),and hydroxy(hydrophilic) was studied at room temperature.The difference in their wetting behavior and the structure of their interfacial water were examined from the estimation of the z density profile,radial distribution function,hydrogen bonds and orientation of water dipoles in the interfacial region.The present simulation results suggest that the wetting behavior of the gold SAM surface can be modified by altering the terminal functional group of the SAM chains.     

Hot corrosion behavior of nanostructured Gd2O3 doped YSZ thermal barrier coating in presence of Na2SO4 + V 2O5 molten salts

Nickel-based superalloy DZ125 was first sprayed with a NiCrAlY bond coat and followed with a nanostructured 2 mol% Gd_2O_3-4.5 mol% Y_2 O_3-ZrO_2(2 GdYSZ) topcoat using air plasma spraying(APS). Hot corrosion behavior of the as-sprayed thermal barrier coatings(TBCs) were investigated in the presence of 50 wt%Na_2SO_4 + 50 wt% V_2O_5 as the corrosive molten salt at 900 ℃ for 100 h. The analysis results indicate that Gd doped YVO_4 and m-ZrO_2 crystals were formed as corrosion products due to the reaction of the corrosive salts with stabilizers(Y_2O_3, Gd_2O_3) of zirconia. Cross-section morphology shows that a thin layer called TGO was formed at the bond coat/topcoat interface. After hot corrosion test, the proportion of m-ZrO_2 phase in nanostructured 2GdYSZ coating is lower than that of nano-YSZ coating. The result reveals that nanostructured 2GdYSZ coating exhibits a better hot corrosion resistance than nano-YSZ coating.     

La2O3–Al2O3 –SiO2 glass-infiltrated 3Y-TZP all-ceramic composite for the dental restora tive application

The 3 mol% yttria stabilized tetragonal zirconia polycrystals (3Y-TZP) powder had three particle size distributions, while the fine one was lower than 100 nm. The 3Y-TZP compact was prepared by dry-pressing under pressures ranged from 10 to 30 MPa and then presintered at 1250°C for 2 h. The matrix dry-pressed under the pressure of 20 MPa had a porosity of 16.7% and could be easily processed by computer aided design and computer aided manufacturing (CAD/CAM), and which had been infiltrated by the La2O3–Al2O3–SiO2 glass at 1200°C for 4 h. The flexural strength and fracture toughness of the composite were 710.7 MPa and 6.51 MPa m^1/2, respectively. The low shrinkage (0.3%) of the composite can satisfy the net-shape fabrication standard. XRD results illustrated that zirconia in the La2O3–Al2O3–SiO2 glass-infiltrated 3Y-TZP all-ceramic composite was mainly in the tetragonal phase. SEM and EDS results indicated that the pores of the matrix were almost filled by the La2O3–Al2O3 –SiO2 glass     

Effects of temperature and stress on the creep behavior of a Ni3Al base single crystal alloy

The creep behavior and microstructure of a Ni3Al base single crystal alloy IC6SX with [001] orientation under the testing conditions of 760 ℃/593 MPa, 980 ℃/205 MPa, and 1100 ℃/75 MPa were investigated. The experimental results showed that Alloy IC6SX had good creep resistance and its creep resistance at elevated temperatures was similar to the second generation nickel-base single crystal alloy containing Re. TEM analysis indicated that the dislocation configuration and movement pattern were different under different temperature and stress conditions. It has been found that under the test condition of 1070 ℃/137 MPa the dislocations moved within the γ channel during the primary creep stage, and the motion of dislocations were prevented by the matrix of γ′ phase, which reduced the creep rate of the alloy. In the secondary creep stage, dislocations cut into the γ′ phase from the γ/γ′ interface. However in the third creep stage, the dislocation pileups were observed in both γ and γ′ phase, and dislocation multiplication occurred when the dislocations with different Burgers vector met and reacted each other.     

Electroch emical properties and interfacial reactions of LiNi0.5Mn1.5O4-δ nanorods

LiNi0.5Mn1.5O4-δ which possesses a high voltage of 4.7 V vs.Li+/Li and stable structure has been considered as a promising cathode material for high energy Li-ion batteries.In this study,well-crystalli...     

Effect of Sr on microstructure and aging behavior of Mg–14Li alloys

The as-cast and as-extruded Mg–14 wt%Li–x Sr ( x=0.14, 0.19, 0.39 wt%) alloys were,respectively, prepared through a simple alloying process and hot extrusion. The effects of Sr addition on microstructure and aging behavior of the Mg–14 wt%Li–xSr alloys were studied. The results indicated that β(Li) and Mg2Sr were the two primary phases in the microstructures of both as-cast and as-extruded Mg–14 wt%Li–xSr alloys. Interestingly, with the increase of Sr content from 0.14 wt% to 0.39 wt%, the grain sizes of the as-cast and as-extruded Mg–14 wt%Li–xSr alloys markedly decreased from 5000mm and 38mm to 330 mm and 22mm respectively, while no obvious changes of the micro-hardness and microstructure of the as-extruded alloys were observed during the aging treatment.     

Structure evolution of Y2O3 nanoparticle/Fe composite during mechanical milling and annealing

Fe-25 wt% Y2O3composite powders have been fabricated by mechanical milling(MM) Fe powders of 100 μm in diameter and Y2O3nanoparticles in an argon atmosphere for the milling periods of4,8,12,24,36,and 48 h,respectively.The features of these powders were characterized by using X-ray diffraction(XRD),scanning electron microscopy(SEM),electron probe micro analyzer(EPMA) and transmission electron microscopy(TEM).The experimental results showed that the mean particle size and crystalline size of MM powders decreased with the milling time increasing.All the elements distributed homogenously inside the powders after 48 h of MM.The lattice constant of the matrix α-Fe kept constant with the milling time,and no solid solution took place during MM process.After 8 h of MM,the α-Fe in each powder became nanocrystalline.After 48 h of MM,Y2O3changes from nanostructure into amorphous structure,and the crystalline size of α-Fe further decreased to 10 nm.The Y2O3in the powders mechanically milled for 48 h kept the amorphous structure after being annealed at 400 1C,and starts to crystallize when the powders are annealed at 600 1C.The amorphous Y2O3contains a small amount of Fe,and crystalline FeYO3appears at 800 1C.     

Abnormal thermal shock behavior in electrical conductivity of Ti2SnC

Some ternary carbide and nitride ceramics have been demonstrated to exhibit abnormal thermal shock behavior in mechanical properties. However, the influence of thermal shock on other properties is not clear. This work reports on the influence of thermal shock on electrical conductivity of Ti_2SnC as a representative member of ternary carbides. Abnormal change in electrical conductivity was first demonstrated during quenching Ti_2 SnC in water at 500-800 ℃. The residual electrical conductivity of the quenched Ti_2SnC gradually decreased with increasing temperature, but abnormally increased after quenching at 600 ℃. The microstructure of surface cracks was characterized. The main mechanism for the abnormal electrical conductivity recovery is that some narrow branching cracks are filled by metallic Sn precipitating from Ti_2SnC.     

Facile synthesis of nanosized sodium magnesium hydride, NaMgH3

The ternary magnesium hydride NaMgH 3 has been synthesised via reactive milling techniques.The method employed neither a reactive H2 atmosphere nor high pressure sintering or other post-treatment processes.The formation of the ternary hydride was studied as a function of milling time and ball:powder ratio.High purity NaMgH 3 powder(orthorhombic space group Pnma,a 5.437(2),b 7.705(5),c 5.477(2) ;Z 4) was prepared in 5 h at high ball:powder ratios and characterised by powder X-ray diffraction(PXD),Raman spectroscopy and scanning electron microscopy/energy dispersive X-ray spectroscopy(SEM/EDX).The products formed sub-micron scale(typically 200-400 nm in size) crystallites that were approximately isotropic in shape.The dehydrogenation behaviour of the ternary hydride was investigated by temperature programmed desorption(TPD).The nanostructured hydride releases hydrogen in two steps with an onset temperature for the first step of 513 K.     

Microstructure and mechanical properties of Nb–Si alloys fabricated by spark plasma sintering

This paper deals with microstructural evolutions and mechanical properties of Nb-Si binaries containing dual-phase Nb/Nb5Si3 with Nb to Nb5Si3 fraction ratios of 90:10,80:20,70:30 and 50:50,prepared by spark plasma sintering(SPS).Dense Nb/Nb5Si3 samples with a relative density larger than 99.5% were obtained by SPS processing.The SPS samples consist of the Nb and Nb5Si3 phases with less than 3% fraction of NbO oxide.Hv at room temperature,and compressive strength at 1150℃ and 1250 1C of the bulk SPS alloys increase monolithically by enhancing fraction of the stiffening Nb5Si3 phase.For example,0.2% yield strength,σ0.2,increases from 175 MPa to 420 MPa at 1150℃ and from 110 MPa to 280 MPa at 1250℃,when the Nb5Si3 fraction increases from 10% to 50%.It is interesting that the fracture toughness,KQ,of the bulk SPS samples seems not to be sensitive to phase fraction.Heat treatment,however,plays a key role on the KQ as compared with that of the as-sintered state,at the corresponding Nb5Si3 fraction and considerably improves the KQ by about 100% for samples with the Nb5Si3 fractions of 10%-30%,and by about 50% for the sample with 50% Nb5Si3 fraction.