Magnetoelectric and converse magnetoelectric res ponses in TbxDy1-xFe2-y alloy ＆ Pb（Mg1/3Nb2/3）（1-x）TixO3 crystal laminated composites

Measured results of magnetoelectric （ME） and converse magnetoelectric （CME） effects of TbxDy1-xFe2-y/ Pb（Mg1/3Nb2/3）（1-x）TixO3/TbxDy1-xFe2-y （TD/PMNT/TD） and PMNT/TD/PMNT laminated composites are presented. ME effect was determined by measuring laminate voltage output under a Helmholtz-generated AC field biased by a DC field （0-1 kOe） （1Oe = 79.58 A/m）. The CME effect was measured by recording the voltage induced in a solenoid encompassing the ME sample while exposed to a DC bias field and PMNT layer driven by a 10 V AC source. The ME and CME responses in the two laminated structure are linear. The highest values of ME coefficients in TD/PMNT/TD and PMNT/TD/PMNT composites are 384 mV/Oe and 158 mV/Oe, respectively, while the highest values of CME coefficients in the two composites are 118 mG/V and 162 mG/V （1 G=10^-4 T）, respectively.     

Performances improvement of eosin Y sensitized solar cells by modifying TiO2 electrode with silane-coupling reagent

Chemical fixing of xanthene dye （eosin Y） on the surface of TiO2 electrode was carried out by modifying the electrode with silane-coupling reagent to obtain stable dye-sensitized TiO2 electrode. Such silane modification can not only evidently enhance the stability of dye-sensitized TiO2 electrode but also improve the energy conversion efficiency of the assembled cells by increasing short-circuit photocurrent （Jsc） and open-circuit photovoltage （Voc）. It was found that the improvements of cell performances differ depending on the composition of the electrolyte. The optimum cell of the cell performance was achieved in the electrolyte with 0.5 mol/L TBAI/0.05 mol/L 12/EC：PC（3：1 w/w）, yielding Jsc of 4.69 mA. cm-2, Voc of 0,595 V, fill factor （FF） of 0.64 and ηof 1,78%, Different spectroscopic techniques including UV-Vis spectra, fluorescence spectra, EIS and dark current measurements were employed to derive reasonable analysis and explanations.     

Relaxor behavior of (1-x)Pb(Mg1/3Nb2/3)O3-xPbTiO3 ceramics

n the present work, the phase transitions and relaxor behavior of (1−x)Pb(Mg_1/3Nb_2/3)O₃-xPbTiO₃ (PMN-PT, x = 0.2―0.4) ferroelectric ceramics have been investigated by means of X-ray diffraction, di-electric spectroscopy, the P-E hysteresis loop measurements and Raman scattering techniques. Structural analysis revealed that with the increase of PbTiO₃ content, PMN-PT ceramics experienced a gradual phase transition process from rhombohedral to tetragonal. It is usually believed that such kinds of phase transitions resulted in the linear decrease of relaxation degree. Surprisingly, our analy-sis of the dielectric spectra revealed that the indicator of the degree of diffuseness γ reached the maximum value near morphotropic phase boundary (MPB) (x = 0.32), then decreased with the further increase of PbTiO₃ content. The large dielectric relaxor feature near MPB may be attributed to the for-mation of ordered nanodomains, resulting from complex coexisting nanostructures. Further, the P-E hysteresis loop measurements and Raman analysis of the B-site cation order correlated well with the dielectric measurement results. It was found that the hysteresis loop squareness R_sq received the minimum value while the inverse of the value of full wide of half maximum (FWHM) of A_1g mode reached the maximum value at MPB composition, which showed similar trends to γ.     

An in-situ DRIFTS study in the reaction between NO x and soot on BaAl2O4

The interactions between NO, O2 and their mixture on BaAl2O4, as well as the reaction of NOx with soot in the presence of O2, have been investigated using Diffuse Reflectance Infrared Fourier Transform Spectroscopy （DRIFTS）. NO adsorption produces only nitrites species in the absence of O2. NO2 adsorption produces nitrates species besides nitrites species. The produced nitrites will further react with O2, Osurf^-. and Olattice^2- to form nitrates. The reaction of NOx with soot begins with the reaction of nitrates with soot oxygenated complex （C（O））, which is regarded as the key and rate determining step. A reaction pathway is proposed for the catalyzed reaction of NOx with soot in the presence of O2.     

Synthesis and characterization of BiFeO3 nanotube arrays and Y-junction BiFeO3 nanotubes

Multiferroic BiFeO₃ (BFO) nanotube arrays (∼100 nm in diameter and ∼50 μm in length) were synthesized by the sol-gel method utilizing the anodic aluminum oxide (AAO) membrane technique. The microstructure and chemical components of the BFO nanotubes were investigated using scanning electron microscopy (SEM), transmission electron microscopy (TEM) and X-ray photoelectron spectrometer (XPS). The BFO nanotubes exhibited polycrystalline microstructures. The novel Y-junction BFO nanotubes were simultaneously fabricated. Supported by the National Natural Science Foundation of China (Grant No. 90306010), Program for New Century Excellent Talents in University (Grant No. NCET-04-0653) and National Basic Research Program of China (Grant No. 2007CB616911)     

Preparation of Fe3O4@Au nano-composites by self-assembly technique for immobilization of glucose oxidase

Superparamagnetism amination nanocrystals Fe₃O₄ with 3-aminopropyltriethyloxy silane (APTES) were prepared by modified co-precipitation method. Next, 4-5 nm gold nanoparticles, prepared by classical Frens procedure, were coated on the surface of the amination Fe₃O₄ by self-assembly technology. The prepared Fe₃O₄@Au nanocomposite particles were investigated by transmission electron microscopy (TEM), UV-vis, infrared spectrum (FT-IR), and vibrating sample magnetometer (VSM) in order to elucidate the morphology, optics and magnetic properties of the nanocomposites. Their uniform distribution of particle size, which is about 15 nm, and good magnetic responsiveness were observed. In view of the fact that Fe₃O₄ owns superparamagnetism and that nano-gold can readily combine with biological molecules, glucose oxidase (GO _x ) was chosen as a model to penetrate the condition of immobilizing enzyme, and enzymatic properties of resultant immobilized enzyme were studied as well. By systematic optimization, we established that at 28°C, and pH (5.5) and when mole ratio of Fe₃O₄:HAuCl₄ was 0.5:1, the immobilization provided the best results. Finally, we are glad to find that the immobilized enzyme exhibits excellent thermostability in addition to its better stability than free enzyme. Thus, herein described immobilized enzyme could be used repeatedly with the assistance of an external magnetic field. Supported by the Science Foundation of Sichuan Province, China (Grant No. 2005A033) and Science Foundation of Sichuan Agricultural University for Distinguished Young Teachers (Grant No. 007202)     

Preparation and magnetic properties of CoFe2O4/TiO2 composite films

Using （Ti（OC4H9）4） and metal chlorates as starting materials, CoFe2O4/TiO2 composite films were prepared by sol-gel method. The effects of heat treatment temperature and pH of the precursor on microstructure and magnetic properties were studied. The phase structure of the samples was examined by X-ray diffraction. The microstructure was examined by scanning electron microscope, atomic force microscope and polarized microscope. The magnetic property was measured by vibrating sample magnetometer. The results show that the crystals of different phases grow up independently. CoFe2O4 is uniformly embedded into the TiO2 matrix in the prepared composite films, and the growth of composite films is dependent on the heat treatment temperatures and PH of the precursor. The average size of CoFe2O4 crystal is 19 nm in Nanocomposite film prepared when the heat treatment temperature is 800℃ and the pH of the precursor is between 2 and 3. The magnetism of the composite films is enhanced as the heat treatment temperature increases.     

Photovoltaic properties of MEH-PPV/TiO2 nanocomposites

Photovoltaic properties of photodiodes based on nano-TiO2 and poly[2-methoxy,5-（2＇-ethlhexyloxy）-p-phenylenevinylene] （MEH-PPV） composites are investigated. By comparing composite devices with the same weight of TiO2 （nanoparticles and nanotubes）：MEH-PPV, it was found that the device with TiO2 nanotubes exhibited better performance. By further optimizing the weight radio of TiO2 nanotubes： MEH-PPV, we gained the device with a short circuit current density of 9.27μA/cm^2 with a light intensity of 16.7mW/cm^2 at the 500 nm wavelength, the highest open-circuit voltage of 1.1V, and a photosensitivity of 332 at reverse bias of -0.6V. The photosensitivity is improved by a factor of 33 compared with the undoped MEH-PPV device.     

Micro-Raman investigations on the structures of the surface and the inner of MgSO<Subscript>4</Subscript> droplets

Spherical MgSO4 droplets were deposited by a syringe on the hydrophobic Teflon substrate. Using micro-Raman technique, the laser beam was highly focused twice on the surface and in the center of spherlcel droplets. The Raman spectra for the surface and the inner of MgSO4 droplets were accordingly obtained, suggesting formation of a thin layer of gels on MgSO4 droplets at low relative humidity. The gel layer covered the surface and exhibited a significant delay in response to the change of amblent relative humidity, resulting in the structural difference between the surface and the inner of MgSO4 droplets.     

Direct electrochemistry and electrocatalysis of horseradish peroxidase in MnO2 nanosheet film

A novel material MnO2 nanosheet has been used as the support matrix for the immobilization of horseradish peroxidase （HRP）. HRP entrapped in MnO2 nanosheet film exhibits facile direct electron transfer with the electron transfer rate constant of 6.86 s^-1. The HRP/MnO2 nanosheet film gives a reversible redox couple with the apparent formal peak potential （E^0＇） of -0.315 V （vs. Ag/AgCl） in pH 6.5 phosphate buffer solution （PBS）. The formal potential E^0＇ of HRP shifts linearly with pH with a slope of -53.75 mV.pH^-1, denoting that an electron transfer accompanies single-proton transportation. The immobilized HRP shows an electrocatslytic activity to the reduction of H2O2. The response time of the biosensor for H2O2 is less than 3 s, and the detection limit is 0.21 μmol · L^-1 based on signal/noise = 3.     

Crystallization dynamics of supersaturated NaClO4 aerosols studied by high-speed photography

Single supersaturated NaClO4 aerosol droplets on a quartz substrate were observed by a high-speed video camera for their morphologic changes with decreasing relative humidity （RH）. The supersaturated droplets were found to form anhydrous NaClO4 at -10% RH. Three stages were roughly observed in this process, i.e., the main stem appearance, primary and secondary branches growth, and the deep dehydration. The main stem grew steadily and finished in 120 ms. Affected by both crystal precipitation and water evaporation, primary branches grew for 1200 ms, accompanied by a slower growth of secondary branches. The deep dehydration was more complicated, and lasted for a longer time.     

Characterization of PM2.5/PM2.5-10 and source tracking in the juncture belt between urban and rural areas of Beijing

Coarse （PM2.5-10） and fine （PM2.5） atmospheric particulate samples were collected in summer and winter during 2005-2007 in the juncture belt between urban and rural areas of Beijing. Elements, ions, organic/elemental carbon （OC/EC） and polynuclear aromatic hydrocarbons （PAHs） were determined to obtain some latest information about the particulate pollution in the juncture belt of Beijing. Particulate matter levels at this site were high as compared with the levels at other sampling sites in Beijing. Pollution elements, secondary ions and PAHs were enriched in fine particles rather than in coarse particles. An obvious seasonal variation of the chemical composition of PM was observed. Source apportionment results showed that secondary components were the largest mass contributor of PM2.5, accounting for 28%; whereas soil-related sources were the largest contributor of PM2.5-10, explaining about 49% of the total mass. The abnormal levels of soil heavy metals at the electronic waste disassembly site in the upwind villages suggested the potential impact of such activities to the environment.     

Preparation and performance of LiNi0. 8Co0.2O2 cathode material based on Co-substituted α-Ni（OH）2 precursor

Co-substituted α-Ni（OH）2 was synthesized by a novel microwave homogeneous precipitation method in the presence of urea. LiNi0.8Co0.2O2 cathode material was synthesized by calcining Co-substituted α-Ni（OH）2 precursor and LiOH·H2O at 900℃for 10 h in flowing oxygen. XRD, FTIR, FESEM and electrochemical tests were used to study the physical and the electrochemical performances of the materials. The results show that the prepared LiNi0.8Co0.2O2 compound has a good layered hexagonal structure. Moreover, the LiNi0.8Co0.2O2cathode material demonstrates stable cyclability with a high initial specific discharge capacity of 183.9 mAh/g. The good electrochemical performance could be attributed to the uniform distribution of Ni^2＋ and Co^2＋ ions in the crystal structure and a minimal cation mixing in LiNi0.8Co0.2O2 host structure.     

Photodegradation of <Emphasis Type="Italic">N</Emphasis>-nitrosodiethylamine in water with UV irradiation

The direct photolysis of N-nitrosodiethylamine （NDEA） in water with ultraviolet （UV） irradiation was investigated. Results showed that NDEA could be completely degraded under the direct UV irradiation. The effects of the experimental conditions, including the initial concentration of NDEA, humic acid and solution pH, were studied. The degradation products of NDEA were identified and quantified with gas chromatography-mass spectrometry （GC-MS） and high performance liquid chromatography （HPLC）. It was confirmed that methylamine （MA）, dimethylamine （DMA）, ethylamine （EA）, diethylamine （DEA）, NO2^- and NO3^- were the main degradation products. The photolysis degradation mechanism of NDEA was also discussed. As a result of N-N bond fission, NDEA was degraded by direct UV irradiation.     

Decoration of C60 nanorods with nickel and their magnetic properties

We studied the coating of C60 nanorods with nickel by electroless plating method and investigated their magnetic properties. The morphology and structure of the nickel layer coated on C60 nanorods were characterized by transmission electron microscopy （TEM）, energy-dispersive X-ray spectroscopy （EDX）, X-ray diffraction （XRD） and Raman spectroscopy. The coated nickel is in the form of nano-sized crystals and becomes a continuous layer as reaction time increases. The hysteresis loop shows a super paramagnetic characteristic similar to that of nanometer-sized nickel particle. These results suggest that the average size of nickel particles on C60 rods is below 10 nm. Our study has shown that electroless plating is an efficient and simple method for coating C60 nanorods with nickel.     

Vegetation evolution on the central Chinese Loess Plateau since late Quaternary evidenced by elemental carbon isotopic composition

There are many controversial issues in loess studies such as natural vegetation types on the Chinese Loess Plateau during the historical periods and the spatial and temporal evolution of C3/C4 plants. Elemental carbon isotopic composition （δ^13Cec） in the loess section may offer new evidence for these problems. Elemental carbon （EC） is produced by incomplete combustion of vegetation, and its carbon isotopic composition has a very small difference from that of the formal vegetation, then δ^13Cec can be used as a record to recover the changes of vegetation. Elemental carbon was extracted by applying the oxidation method from the Ioess-paleosol sequence in the central Chinese Loess Plateau, and its car- bon isotope composition was analyzed by the isotope mass spectrometer. The results showed that the vegetation in this region was a mixed type of C3 and C4 plants, dominated with C3 plants in most of the time. Since late Quaternary, C3/C4 plants may not follow a simple glacial-interglacial cycle mode on the Chinese Loess Plateau, but showing fluctuations. C3 plants increased gradually in L4 period, and more C3 plants occurred during $3 period, and C4 plants increased again during L3-- L2 periods, after that, Cs plants dominated again during S1 --S0 periods. During periods of paleosol development, C3 plants were abundant in S3 and S1, and there were more Ca plants in S2 and SO. During periods of loess sedimen- tation, there were more C3 plants in L4 and L1, and there were more C4 plants in L3 and L2. On the orbital timescale, the vegetation variations revealed by δ^13Cec record are consistent with the results of pollen data and also similar to the results obtained by organic carbon isotopic composition since the last glacial period.     

TiO2-based building materials: Above and beyond traditional applications

In the 1910s, TiO₂ began to be used in building materials as pigments and opacifier due to its excellent optical property. Since the photocatalytic property of TiO₂ was observed in 1972, its application field was expanded to air cleaning and sterilization. Thereafter, people added TiO₂ into building materials to develop novel and facile building materials. These materials were widely used for air cleaning, sterilization, self-cleaning, anti-fogging, decoration, and building cooling. The combination of building and other functions can serve simultaneously. Although TiO₂-based building materials have bright prospects, some aspects such as improving the stability and enhancing photoactive performance of the materials are of importance for future research. Supported by the National High Technology Research and Development Program (“863” Program) of China (Grant No. 2007AA061402), Chinese Key Technology Research and Development Program of the Eleventh Five-year Plan (Grant No. 2006BAJ02A08), Hangzhou Science & Technology Development Program (Grant No. 20061133B27) and Research Fund for the Doctoral Program of Higher Education (Grant No. 20070335197)     

<Emphasis Type="Italic">Ab initio</Emphasis> study of the effects of Ag/Mn doping on the electronic structure of LiFePO<Subscript>4</Subscript>

Based on density functional theory （DFT） of the first-principle for the cathode materials of lithium ion battery, the electronic structures of Li（Fe1-x）PO4 （Me = Ag/Mn, x = 0-0.40） are calculated by plane wave pseudo-potential method using Cambridge serial total energy package （CASTEP） program. The calculated results show that the Fermi level of mixed atoms Fe1-xAgx moves into its conduction bands （CBs） due to the Ag doping. The Li（Fe1-xAgx）PO4 system displays the periodic direct semiconductor characteristic with the increase of Ag-doped concentration. However, for Fe1-xMnx mixed atoms, the Fermi level is pined at the bottom of conduction bands （CBs）, which is ascribed to the interaction between Mn（3d） electrons and Fe（4s） electrons. The intensity of the partial density of states （PDOS） near the bottom of CBs becomes stronger with the increase of Mn-doped concentration. The Fermi energy of the Li（Fe1-xMnx）PO4 reaches maximum at x = 0.25, which is consistent with the experimental value of x = 0.20. The whole conduction property of Mn-doped LiFePO4 is superior to that of Ag-doped LiFePO4 cathode material, but the structural stability is reverse.     

Fine mapping of the red plant gene R1 in upland cotton(Gossypium hirsutum)

Sub 16 is a substitution line with G. hirsutum cv. TM-1 genetic background except that the 16th chromosome (Chr. 16) is replaced by the corresponding homozygous chromosome of G. barbadense cv. 3-79, and T586 is a G. hirsutum multiple gene marker line with 8 dominant mutation genes. The R ₁ gene for anthocyanin pigmentation was tagged in Chr. 16 in T586. The objective of this research was to screen SSR markers tightly linked with R ₁ by using the F₂ segregating population containing 1259 plants derived from the cross of Sub 16 and T586 and the backbone genetic linkage map from G. hirsutum×G. barbadense BC₁ newly updated by our laboratory. Genetic analysis suggested that the segregation ratio of red plants in the F₂ population fit Mendelian 1:2:1 inheritance, confirming that the red plant trait was controlled by an incomplete dominance gene. Preliminary mapping of R ₁ was conducted using 237 randomLy selected F₂ individuals and JoinMap v3.0 software. Then, a fine map of R1 was constructed using the F₂ segregating population containing 1259 plants, and R ₁ was located between NAU4956 and NAU6752, with only 0.49 cM to the nearest maker loci (NAU6752). These results provided a foundation for map-based cloning of R ₁ and further development of cotton cultivars with red fibers by transgenic technology. Supported by National Natural Science Foundation of China (Grant No. 30730067) and Programme of Introducing Talents of Discipline to Universities (Grant No. B08025)     

Evolution of the serum resistance-associated SRA gene in African trypanosomes

Serum resistance-associated (SRA) protein, a protein unique for Trypanosoma brucei rhodesiense, is responsible for resistance of this parasite to the lysis by normal human serum (NHS) and is a vital molecular marker to distinguish this species from other African trypanosomes. We cloned and sequenced the SRA basic copy (SRAbc) gene from T. b. rhodesiense and related species and found that this gene is confined to the subgenus Trypanozoon. The average 82% identity among the sequenced SRAbc genes indicates that they may have a common origin and are highly conserved. Since SRAbc coexists in the T. b. rhodesiense genome with SRA, we propose that SRAbc might be the ‘donor VSG’, which after duplication became inserted into the expression site by recombination. Under natural selection, SRAbc could reform into SRA following mosaic formation. Supported by National Natural Science Foundation of China (Grant Nos. 30570245, 30670275), Changjiang Scholars and Innovative Research Team in University (Grant No. DPCKSCU/IRT0447), International Foundation for Science of Sweden (Grant No. B/4318-1), Grant Agency of the Czech Republic (Grant No. Z60220518) and Education Foundation of the Czech Republic (Grant No. 2B06129)