Preparation and characterization of porous ceramics prepared by kaolinite gangue and Al(OH)<Subscript>3</Subscript> with double addition of MgCO<Subscript>3</Subscript> and CaCO<Subscript>3</Subscript>

Porous ceramics were prepared from kaolinite gangue and Al(OH)₃ with double addition of MgCO₃ and CaCO₃ by the pore-forming in-situ technique. The characterizations of porous ceramics were investigated by X-ray diffractometry, scanning electron microscopy, and mercury porosimetry measurements, etc. It is found that although the decomposition of MgCO₃ and CaCO₃ has little contribution to the porosity, the double addition of MgCO₃ and CaCO₃ strongly affects the formation of liquid phase, and then changes the phase compositions, pore characterization, and strength. The appropriate mode is the sample containing 1.17wt% MgCO₃ and 1.17wt% CaCO₃, which has high apparent porosity (41.0%), high crushing strength (53.5 MPa), high mullite content (76wt%), and small average pore size (3.24 μm).     

Chemical quenching and inhibition of positronium in Cr<Subscript>2</Subscript>O<Subscript>3</Subscript>/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> catalysts

The pore structure of Cr2O3/Al2O3 catalysts and the surface chemical properties of these pores were characterized by positron lifetime and coincidence Doppler broadening (CDB) measurements. Four lifetime components could be resolved from the positron lifetime spectrum, with two long lifetime components and two short lifetime components. The two long lifetimes τ4 and τ3 are attributed to ortho-positronium (o-Ps) annihilation in large pores and microvoids, respectively. With increasing Cr2O3 content, both τ4 and its intensity I4 show sharp decrease, while τ3 and its intensity I3 keep nearly unchanged. The Doppler broadening S parameters also show sharp decrease with increasing Cr2O3 content. Detailed analysis of the CDB spectrum reveals that the parapositronium (p-Ps) intensity also decreases with increasing Cr2O3 content. This indicates that the change of o-Ps lifetime τ4 is due to the chemical quenching by Cr2O3 but not spin-conversion of positronium. The decrease of o-Ps intensity I4 indicates that Cr2O3 also inhibits positronium formation.     

Character and fabrication of Al/Al<Subscript>2</Subscript>O<Subscript>3</Subscript>/Al tunnel junctions for qubit application

The superconductive Josephson junction is the key device for superconducting quantum computation. We have fabricated Al/Al2O3/Al tunnel junctions using a double angle evaporation method based on a suspended shadow mask. The Al2O3 junction barrier has been formed by introducing pure oxygen into the chamber during the fabrication process. We have adjusted exposure conditions by changing either the oxygen pressure or the oxidizing time during the formation of tunnel barriers to control the critical current density Jc and the junction specific resistance Rc. Measurements of the leakage in Al/Al2O3/Al tunnel junctions show that the devices are suitable for qubit applications.     

Dissolution of Al<Subscript>2</Subscript>TiO<Subscript>5</Subscript> inclusions in CaO-SiO<Subscript>2</Subscript>-Al<Subscript>2</Subscript>O<Subscript>3</Subscript> slags at 1823 K

Al-Ti-O inclusions always clog submerged nozzles in Ti-bearing Al-killed steel. A typical synthesized Al₂TiO₅ inclusion was immersed in a CaO-SiO₂-Al₂O₃ molten slag for different durations at 1823 K. The Al₂TiO₅ dissolution paths and mechanism were revealed by scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS). Decreased amounts of Ti and Al and increased amounts of Si and Ca at the dissolution boundary prove that inclusion dissolution and slag penetration simultaneously occur. SiO₂ diffuses or penetrates the inclusion more quickly than CaO, as indicated by the w(CaO)/w(SiO₂) value in the reaction region. A liquid product (containing 0.7–1.2 w(CaO)/w(SiO₂), 15wt%–20wt% Al₂O₃, and 5wt%–15wt% TiO₂) forms on the inclusion surface when Al₂TiO₅ is dissolved in the slag. Al₂TiO₅ initially dissolves faster than the diffusion rate of the liquid product toward the bulk slag. With increasing reaction time, the boundary reaches its largest distance, the Al₂TiO₅ dissolution rate equals the liquid product diffusion rate, and the dissolution process remains stable until the inclusion is completely dissolved.     

Effect of Ag addition on the thermal stability and glass-forming ability of Zr<Subscript>35</Subscript>Ti<Subscript>30</Subscript>Cu<Subscript>7.5</Subscript>Be<Subscript>27.5</Subscript> bulk metallic glass

The thermal stability and glass forming ability (GFA) of Zr35-xTi30Cu7.5Be27.5Agx (x = 0-10) alloys were studied by X-ray diffraction (XRD), differential scanning calorimetry (DSC) and ultrasonic techniques. We found that the addition of 1 at.% Ag can considerably enhance the GFA as indicated by an increase in the critical glass dimension from 15 mm in the Zr35Ti30Cu7.5Be27.5 alloy to 20 mm in the Zr34Ti30Cu7.5Be27.5Ag1 alloy. However, with the addition of more Ag the supercooled liquid region (△Tx) and y parameter (defined as Tx/(Tg+Tl)) drastically decreased from 155 K and 0.436 to 76 K and 0.363, respectively, resulting in a decrease in the GFA. Additionally, the elastic constant (the ratio of shear modulus to bulk modulus or Poisson’s ratio) was also used as a gauge to evaluate the GFA in Zr35-xTi30Cu7.5Be27.5Agx alloys.     

Synthesis of highly ordered SnO2／Fe2O3 composite nanowire arrays by electrophoretic deposition method

Highly ordered SnO2/Fe2O3 composite nanowire arrays have been synthesized by electrophoretic deposition method. The morphology and chemical composition of SnO2/Fe2O3 composite nanowire arrays are characterized by SEM, TEM, EDX, XPS, and XRD. The results show that the SnO2/Fe2O3 composite nanowires are about 180 nm in width and tens of microns in length, and they are composed of small nanoparticles of tetraganal SnO2 and rhombohedral α-Fe203 with diameters of 10-15nm. The SnO2/Fe2O3 composite nanowires are formed by a series of chemical reactions.     

CaCO<Subscript>3</Subscript> film synthesis from ladle furnace slag: morphological change,new material properties,and Ca extraction efficiency

A rapidly air-cooled ladle furnace slag (RA-LFS), which is a type of steelmaking slag discharged from a steel mill, was used to synthesize CaCO₃ film. The CaCO₃ film with 35 cm2 of surface area was synthesized under atmospheric conditions, and the surface morphology of the CaCO₃ films was changed by using additives (CaCl₂ and ethylene glycol). Especially, the addition of CaCl₂ changed the surface morphology of CaCO₃ film with pore and induced new material properties, such as water adsorption. The (012) face of CaCO₃ film (calcite) was rapidly decreased by the addition of CaCl₂. The major components of RA-LFS were calcium (type of CaO, 53.9wt%) and aluminum (type of Al₂O₃, 37.9wt%), and the major crystal phases of RA-LFS were C₃S, C₁₂A₇, and C₃A. The calcium extraction efficiency of RA-LFS was significantly increased after the CaCO₃ film synthesis. The material properties (hardness and elastic modulus) and the thermal characteristics of the CaCO₃ films were analyzed by nano-indentation and thermogravimetry-differential thermal analysis. The synthesized CaCO₃ films from RA-LFS and Ca(OH)₂ (reagent) showed similarities in terms of their material properties and the decomposition temperature.     

Synthesis and modification of well-ordered layered cathode oxide LiNi<Subscript>2/3</Subscript>Mn<Subscript>1/3</Subscript>O<Subscript>2</Subscript>

Oxalic-acid-based co-precipitation method was employed to prepare LiNi_2/3Mn_1/3O₂ sample with a high-ordered structure. Li⁺, Ni²⁺ and Mn²⁺ acetates were used as starting materials. The influence of the amount of lithium source in the starting materials on Li⁺ content, disorder of Li⁺-Ni²⁺ ions, and electrochemical performance has been investigated. Rietveld refinement shows that the sample prepared with 20% excess Li-source in the starting materials exhibits a perfect ordered structure. A specific discharge capacity is as high as 172 mAh/g at C/20 in the voltage range of 4.35–2.7 V. However, the cyclability is not satisfactory: about 25.3% fade in capacity was observed over 50 cycles. Chemically stable SiO2 was coated on the surface of LiNi_2/3Mn_1/3O₂ particles. A significant improvement in cyclability was attained with 3 wt% SiO2 coating, which is ascribable to the protection of LiNi_2/3Mn_1/3O₂ particles from being dissolved into the electrolyte.     

Near-infrared to visible up-conversion emissions of Er^3＋ doped Al2O3 powders derived from the sol-gel method

The Er3 doped Al2O3 powders were prepared by the sol-gel method using the aluminium isopropoxide [Al(OC3H7)3]-derived Al2O3 sols with addition of the erbium nitrate [Er(NO3)3.5H2O]. The different phase structure, including three crystalline types of (Al,Er)2O3 phases, γ, θ, α, and two Er-Al-O phases, ErAlO3 and Al10Er6O24, was obtained with the 1 mol% Er3 doped Al2O3 powders at the different sintering temperatures of 600―1200℃. The green and red up-conversion emissions centered at about 523, 545 and 660 nm, corresponding respectively to the 2H11/2, 4S3/2→4I15/2 and 4F9/2→4I15/2 transitions of Er3 , were detected by a 978 nm semiconductor laser diodes excitation. The phase structure and OH content had evident influence on the up-conversion emissions intensity. The maximum intensities of both the green and red emissions were obtained respectively for the Er3 doped Al2O3 powders sintered at 1200 ℃, which was composed mainly of α-(Al,Er)2O3, less of ErAlO3 and Al10Er6O24 phases, and with the least OH content. The two-photon absorption up-conversion process was involved in the green and red up-conversion emissions of the Er3 doped Al2O3 powders.     

Synthesis, Characterization and Calorimetry of Ni（C4H8N2O3）2Cl2

A coordination complex was synthesized from NiCl2 and dipeptide glycylglycine（GG）. It was characterized by element analysis, NMR and TG methods, and then was determined to be Ni（C4HsN2O3）2Cl2. Using an isoperibolic reaction calorimeter, the standard molar enthalpy of formation of Ni（GG）2Cl2（solid） has been determined to be -（1 674.66±2.02） kJ · mol^-1 at 298.15 K.     

Temperature effect on the corrosion and passivation characterization of Ni<Subscript>82.3</Subscript>Cr<Subscript>7</Subscript>Fe<Subscript>3</Subscript>Si<Subscript>4.5</Subscript>B<Subscript>3.2</Subscript> alloy in acidic media

The effects of temperature on corrosion and the electrochemical behavior of Ni_82.3Cr₇Fe₃Si_4.5B_3.2 glassy alloy in HCl, H₂SO₄, and H₃PO₄ acids were studied using AC and DC techniques. Impedance data reveal that the susceptibility to localized corrosion increases with increasing temperature. Potentiodynamic polarization curves reveal that the bulk glassy alloy is spontaneously passivated at all the investigated temperature in H₂SO₄ and H₃PO₄ solutions. A localized corrosion effect in HCl solution is clearly observed. The apparent activation energies in the regions of Tafel, active, and passive, as well as the enthalpies and entropies of the dissolution process were determined and discussed. The high apparent activation energy (E_a) value for H₃PO₄ solution in Tafel region is explained by the low aggressivity of PO₄3- ions.     

Comparative analysis of the dissolution kinetics of galena in binary solutions of HCl/FeCl<Subscript>3</Subscript> and HCl/H<Subscript>2</Subscript>O<Subscript>2</Subscript>

A comparative study of the dissolution kinetics of galena ore in binary solutions of FeCl₃/HCl and H₂O₂/HCl has been undertaken. The dissolution kinetics of the galena was found to depend on leachant concentration, reaction temperature, stirring speed, solid-to-liquid ratio, and particle diameter. The dissolution rate of galena ore increases with the increase of leachant concentration, reaction temperature, and stirring speed, while it decreases with the increase of solid-to-liquid ratio and particle diameter. The activation energy (E _a) of 26.5 kJ/mol was obtained for galena ore dissolution in 0.3 M FeCl₃/8.06 M HCl, and it suggests the surface diffusion model for the leaching reaction, while the E _a value of 40.6 kJ/mol was obtained for its dissolution in 8.06 M H₂O₂/8.06 M HCl, which suggests the surface chemical reaction model for the leaching reaction. Furthermore, the linear relationship between rate constants and the reciprocal of particle radius supports the fact that dissolution is controlled by the surface reaction in the two cases. Finally, the rate of reaction based on the reaction-controlled process has been described by a semiempirical mathematical model. The Arrhenius and reaction constants of 11.023 s⁻¹, 1.25×10⁴ and 3.65×10² s⁻¹, 8.02×10⁶ were calculated for the 0.3 M FeCl₃/8.06 M HCl and 8.06 M H₂O₂/8.06 M HCl binary solutions, respectively.     

Microwave sintering of Ca<Subscript>0.6</Subscript>La<Subscript>0.2667</Subscript>TiO<Subscript>3</Subscript> microwave dielectric ceramics

Ca_0.6La_0.2667TiO₃ ceramics were prepared by conventional and microwave sintering techniques and their sinterability, microstructure, and microwave dielectric properties were investigated in detail for comparison. Densified Ca_0.6La_0.2667TiO₃ ceramics were obtained by microwave sintering at 1350°C for 30 min and by conventional sintering at 1450°C for 4 h. An unusual phenomenon was found that some larger grains (grain size range: 8–10 μm) inclined to assemble in one area but some smaller ones (grain size range: 2–4 μm) inclined to gather in another area in the microwave sintered ceramics. The microwave dielectric properties of Ca_0.6La_0.2667TiO₃ ceramics prepared by microwave sintering at 1350°C were as follows: dielectric constant (ɛ _r) = 119.6, quality factor (Qf) = 17858.5 GHz, and temperature coefficient of resonant frequency (τ _f) = 155.5 ppm/°C. In contrast, the microwave dielectric properties of the ceramics prepared by conventional sintering at 1450°C were ɛ _r = 117.4, Qf = 13375 GHz, and τ _f = 217.2 ppm/°C.     

Preparation of Al<Subscript>72</Subscript>Ni<Subscript>8</Subscript>Ti<Subscript>8</Subscript>Zr<Subscript>6</Subscript>Nb<Subscript>3</Subscript>Y<Subscript>3</Subscript> amorphous powders and bulk materials

Amorphous Al₇₂Ni₈Ti₈Zr₆Nb₃Y₃ powders were successfully fabricated by mechanical alloying. The microstructure, glass-forming ability, and crystallization behavior of amorphous Al₇₂Ni₈Ti₈Zr₆Nb₃Y₃ powders were investigated by X-ray diffraction (XRD), transmission electron microscopy (TEM), and differential scanning calorimetry (DSC). The isothermal crystallization kinetics was analyzed by the Johnson–Mehl–Avrami equation. In the results, the supercooled liquid region of the amorphous alloy is as high as 81 K, as determined by non-isothermal DSC curves. The activation energy for crystallization is as high as 312.6 kJ·mol?1 obtained by Kissinger and Ozawa analyses. The values of Avrami exponent (n) imply that the crystallization is dominated by interface-controlled three-dimensional growth in the early stage and the end stage and by diffusion-controlled two- or three-dimensional growth in the middle stage. In addition, the amorphous Al₇₂Ni₈Ti₈Zr₆Nb₃Y₃ powders were sintered under 2 GPa at temperatures of 673 K and 723 K. The results show that the Vickers hardness of the compacted powders is as high as Hv 1215.     

Analysis of the factors affecting the magnetic characteristics of nano-Fe<Subscript>3</Subscript>O<Subscript>4</Subscript> particles

We prepared Fe3O4 nanoparticles using chemical coprecipitation and studied the factors affecting the magnetic characteristics of nano-Fe3O4 particles.We identified four factors and three levels of an orthogonal experiment and investigated these four factors that affect the magnetic characteristics of the Fe3O4 particles.We obtained important information from this investigation.The Fe3+ to Fe2+ molar ratio,the iron precursor salt,the amount of surfactant and the amount of alkali were found to be important.We also studied the influence of the order of alkali and surfactant addition,the aging time and the stirring speed on the magnetic characteristics of the nano-Fe3O4 particles.The Fe3O4 preparation process was also analyzed.     

3,4-dichlorotoluene ammoxidation to 3,4-dichlorobenzonitrile over VPO/SiO<Subscript>2</Subscript> catalyst

Ammoxidation of 3,4-dichlorotoluene (DCT) to prepare 3,4-dichlorobenzonitrile (DCBN) over silica supported vanadium phosphorus oxide catalysts has been studied. On the VPO/SiO₂ catalyst, the influence of the reaction temperature, the molar ratio of air/DCT, the molar ratio of NH₃/DCT in the feed gas and the space velocity (v ₁) on the conversion, yield and selectivity was observed. The most appropriate reaction condition is: reactionT=673 K,n(DCT):n(NH₃):n(air)=1:7:30 andv ₁=250 h⁻¹. At this optimum reaction condition, the conversion of DCT is 97.8%; the molar yield of DCBN is 67.4%. It was found that the addition of element phosphorus can improve the yield of DCBN compared with VO/SiO₂ catalyst. Foundation item: Supported by Youth Chen-Guang Project of the Committee of Science and Technology of Wuhan (20015005042) Biography: Huang Chi(1972-), male, Ph D, Lecture, research direction: ammoxidation.     

Preparation of In<Subscript>2</Subscript>S<Subscript>3</Subscript> and Cu-Doped In<Subscript>2</Subscript>S<Subscript>3</Subscript> 2D Ultrathin Nanoflakes with Tunable Absorption and Intense Photocurrent Response

We reported an effective method to synthesize In₂S₃ and Cu-doped In₂S₃ two-dimensional ultrathin nanoflakes by the hydrothermal method through tuning the Cu/In molar ratio. The transmission electron microscope images showed that the products had ultrathin flake-like shape with wrinkling and rolling. The X-ray diffraction patterns indicated the crystal phase of nanoflakes was varied from β-In₂S₃ to tetragonal-CuInS₂ as the Cu/In molar ratio was increased. The In₂S₃ nanoflakes exhibited absorption band at 450 nm, while new absorption peaks in turn appeared at 550 nm and 670 nm as the Cu/In molar ratio was increased. In addition, the two-dimensional ultrathin nanoflakes exhibited intense photocurrent response.     

Preparation and luminescence characteristics of Sr3SiO5：Eu^2＋ phosphor for white LED

The Sr3SiO5：Eu^2＋ phosphor was synthesized by high temperature solid-state reaction. The emission spectrum of Sr3SiO5：Eu^2＋ shows two bands centered at 487 and 575 nm, which well agree with the theoretic values of emission spectrum. The excitation spectrum for 575 nm emission center has several excitation bands at 365, 418, 458 and 473 nm. And the results show that the emission spectrum of Sr3SiO5：Eu^2＋ is influenced by the Eu^2＋ concentration. The relative emission spectra of the white-emitting InGaN-based YAG：Ce^3＋ LED and Sr3SiO5：Eu^2＋ LED were investigated. The results show that the color development of InGaN-based Sr3SiO5：Eu^2＋ is better than that of InGaN-based YAG：Ce^3＋, and the CIE chromaticity of InGaN-based Sr3SiO5：Eu^2＋ is （x=0.348, y=0.326）.     

Different climatic controls of soil δ 13Corg in three mid-latitude regions of the Northern Hemisphere since the Last Glacial period

Paleoecological records of soil δ^13Corg from three regions in the middle latitudes of the Northern Hemisphere, including the Chinese Loess Plateau （CLP）, the Great Plains and adjacent areas of North America and northwestern Europe, showed different variations since the Last Glacial period. An attempt was made to evaluate the causes for the difference in δ^13Corg on the basis of the modern climatic data collected in these regions and of the modern C3 and C4 plant distributions. The analysis indicates that temperature, especially the growing season temperature, has a dominant control on the growth of C4 plants. When the mean annual or growing season temperatures are below the ＂threshold value＂, the growth of C4 plants is limited. When the temperature is above the ＂threshold value＂, C4 plants can grow under a wide range of precipitation. However, when the precipitation is high enough to favor the growth of trees, the proportions of C4 plants in local biomass will decline. The implicit control factor recovered by sedimentary records is consistent with the control factor on modern C3/C4 distribution. Pure C3 plants have been dominating the local biomass since the Last Glacial period in European loess region, mainly owing to the low local temperature. The increases in C4 plants from the late Pleistocene to the Holocene in the Chinese Loess Plateau, the Great Plains and adjacent areas, mainly reflect the influence of increasing temperature.     

He-H2 mixture and Er3NiHx packing for the refrigeration enhancement of pulse tube refrigerator

The computation with the theory of modified Brayton Cycle indicates that higher cooling power and coefficient of performance for a pulse tube refrigerator can be achieved with He-H2 mixture as working gas than those with pure He in the temperature region of 30 K. In addition, it is found that Er3Ni, a regenerative material, is able to absorb H2 and produces Er3NiHx. The computation presents that the regenerative performance of Er3NiHx is better than that of Er3Ni due to its higher volume specific heat. Experimental results show that the pulse tube refrigeration performance in 30 K temperature region is enhanced greatly with He-H2 mixture and Er3NiHx packing.