Coherent thermal radiation in thin films and its application in the emissivity design of multilayer films

The infrared transmission spectra of a 0.54-μm-thick Ge film and a 20-μm-thick Si film were experimentally measured. As the incident radiation was in the wavelength range from 1.5μm to 10μm, the Ge film demonstrated a strongly spectral coherence. However, thermal radiation of the Ge film was found to be spatially incoherent due to its extreme thinness. The Si film exhibited significantly spectral and spatial coherence. The results confirmed that thermal radiation of a monolayer film could be coherent spectrally and spatially if the film thickness was comparable with the wavelength. The optical characteristic matrix method was applied to calculate the transmission spectra of the Si and Ge film, and the results agreed well with the measurements. This method was further used to analyze two multilayer films composed of five low emissive layers. Their emissivities were found to be highly emissive at a certain zenith angle, and the emissive peak could be controlled by careful selection of film thickness.     

Singlebeam two-photon three-dimensional optical storage in a pyrryl-substituted fulgide photochromic material

We introduce a high-density three-dimensional optical data storage approach by using a pyrryl-substituted fulgide photochromic material with a method of single-beam two-photon recording and fluorescence confocal readout. The detailed information about the photochromic material and the experimental setup are presented. The experiments about multi-layered recording and readout are carried out with a 100-μm-thick transparent photochromic material film. The results show that the lateral resolution is better than 1 μm, and the longitudinal resolution is about 3 μm. Besides, the readout times for the recorded data are desirable when using a readout laser power smaller than 5 mW.     

基于烧蚀原理的激光抛光的数值建模与分析

采用连续激光对304不锈钢材料进行了基于烧蚀原理的激光抛光实验,得到了较好的抛光效果.耦合激光抛光中的传热和材料汽化,建立了一个二维瞬态数值模型,仿真了激光抛光中工件表面的演变,预测了激光抛光后工件的表面形貌和表面粗糙度值,仿真结果与实验结果十分接近,误差仅为8.17%.此外,利用该模型研究了激光抛光中工件表面移动速度的分布情况,确定了表面移动速度与初始表面形貌的关系:表面形貌波峰位置的表面移动速度较大,而波谷位置的表面移动速度较小,揭示了基于烧蚀原理的激光抛光降低工件表面粗糙度的机制.     

Silicon field emission arrays coated with CN<Subscript>x</Subscript> thin films

Arrays of silicon micro-tips were made by etching the p-type (1 0 0) silicon wafers which had SiO₂ masks with alkaline solution. The density of the micro-tips is 2×10⁴ cm⁻². The Scanning Electron Microscope (SEM) photos showed that the tips in these arrays are uniform and orderly. The CN_x thin film, with the thickness of 1.27 μm was deposited on the silicon micro-tip arrays by using the middle frequency magnetron sputtering technology. The SEM photos showed that the films on the tips are smoothly without particles. Keeping the sharpness of the tips will benefit the properties of field emission. The X-ray photoelectron spectrum (XPS) showed that carbon, nitrogen and oxygen are the three major elements in the surfaces of the films. The percents of them are C: 69.5%, N: 12.6% and O: 17.9%. The silicon arrays coated with CN_x thin films had shown a good field emission characterization. The emission current intensity reached 3.2 mA/cm² at 32.8 V/μm, so it can be put into use. The result showed that the silicon arrays coated with CN_x thin films are likely to be good field emission cathode. The preparation and the characterization of the samples were discussed in detail. Foundation item: Supported by the National Natural Science Foundation of China (19975035) Biography: Chen Ming an (1978-), male, Ph. D candidate, research direction: novel functional materials film and ion beam modification of materials.     

Field emission of SiCN thin films bombarded by Ar<Superscript>+</Superscript> ions

SiCN thin films were synthesized by a radio frequency chemical vapor deposition (RFCVD) system on P-type Si (1 0 0) wafers using C₂H₄, SiH₄ and N₂ as raw materials, In order to get rid of the oxygen absorbed on the surface and improve the characteristics of electron field emission, Ar⁺ ions of low energy were used to bombard the samples. The field emission characteristics of SiCN thin films before and after Ar⁺ bombardment were studied in the super vacuum environment of 10⁻⁶ Pa. It was showed that the turn-on field (defined as the point where the current-voltage curve shows a sharp increase in the current density) decreased from 38 V/μm before bombardment to 25 V/μm after bombardment. And the maximum emission current density increased from 159.2 to 267.4 μA/cm². The composition before and after Ar⁺ bombardment was compared using X-ray photoelectron spectroscopy (XPS). Our results illustrated that the field emission characteristics were improved after the bombardment of Ar⁺. Foundation item: Supported by the National Natural Science Foundation of China (19975035) Biography: Ma You-peng (1978), male, Master candidate, research direction: novel functional materials film and ion beam modification of materials.     

Electron field emission from nano-crystalline Si films deposited by inductively coupled plasma CVD at room temperature

ELECTRON FIELD EMISSION IS ONE OF THE INTERESTING PER- FORMANCES OF NANO-SCALE MATERIALS [1-3]. CARBON NANO- TUBES HAVE BEEN DEMONSTRATED TO BE THE MOST FASCINAT- ING MATERIAL OF ELECTRON FIELD EMISSION, BUT THEIR INSTA- BILITY OF EMISSION DUE TO THE AGING EFFECT LIMITS THEIR APPLICATION IN VACUUM ELECTRONICS [4]. SI TIPS HAVE MORE FAVORITE GEOMETRIC FEATURE AND MORE STABLE C…     

脉冲CO2激光高精度烧蚀熔石英玻璃

激光抛光是一种能获得超光滑表面新颖的光学元件加工方法,但抛光后表面存在残余波纹和面形畸变.激光高精度烧蚀可用于对元件表面残余波纹和面形进行修正,是一种极具潜力的修形技术.本文开展了激光高精度烧蚀熔石英玻璃的实验,验证了脉冲CO2激光通过控制重叠率可以实现高精度的局部区域均匀烧蚀,并可通过控制激光功率密度获得不同纳米量级的烧蚀深度.但实验发现激光局部区域烧蚀过程存在热累积和过烧蚀的现象.为此建立三维数值模型模拟脉冲CO2激光扫描熔石英表面的过程,对不同重叠率及不同脉冲重复频率作用下熔石英表面温度分布及演变进行分析.数值计算结果表明,重叠率过高将导致熔石英过烧蚀;在合适的重叠率下,高脉冲重复频率会导致明显的热累积.     

Friction characteristics of floppy disks

This note presents the principle and structure of a tribological measure for floppy disks. The precision of the force measuring system is 1 mN in loading and 3×10⁻⁶ N in friction. The resolution of the film thickness between head and floppy disk is 0.5 nm in the vertical and 1.5 nm in the horizontal direction. In order to investigate the tribological characteristics of floppy disks, six types of floppy disks have been tested and the floating properties of these disks are also studied with film measuring system. The experimental results of the surface morphology and friction coefficient of these floppy disks using the atomic force microscope/friction force mcroscope (AFM/FFM) are in accordance with the conclusion made by our own measuring system. The experimental results show that the air film thickness between head and disk is of the same order as the surface roughness of floppy disks.     

Microstructures of metallic film and diamond growth from Fe-Ni-C system

The microstructures of metallic film surrounding diamond have been systemically studied using the transmission electron microscopy (TEM) and the atom force microscopy (AFM). The film can be divided into three layers (inner layer near diamond, external layer near graphite and middle layer). The graphite cannot be directly transformed into diamond in the film at HTHP; there exists a parallel relationship between (−111) of γ-(Fe,Ni) and (110) of Fe₃C in the inner layer; the sawtooth-like step morphology found by AFM on the film is similar to that of corresponding diamond surface. A new model for diamond growth at HPHT is proposed from the parallel relationship and sawtooth-like step morphology. It is believed that Fe₃C may be a transitional phase in the course of diamond growth, γ-(Fe,Ni) in the inner layer can absorb carbon atom groups with lamella structure from Fe₃C, and then the carbon groups stack on growing diamond.     

Evaluation of virus removal in MBR using coliphages T4

A membrane bioreactor (MBR) with gravity drain was tested for domestic wastewater for 65 days. Resultss howed that the effluent quality was excellent, and met with the reuse water standard of China (GB/T 18920-2002). Virus removal in the membrane separation process was investigated by employing coliphages T4 as a tracer. Two microfiltration membrane modules, with pore sizes of 0.22 and 0.1 μm, were used to investigate their effects on virus rejection at the transmembrane pressure of 8.5 kPa. It was found that 0.1 μm membrane had complete rejection of virus, and 0.22 μm membrane had significant rejection of virus. In the longterm operation of this MBR, no significant difference was observed between both pore sizes because the virus concentrations of the effluent in both cases were in the same order. Effluent virus concentration at steady state of MBR running was less than 2 PFU/mL. The removal ratios of coliphage T4 in MF processes were more than 10^5.5. The membrane surface deposits played an important role in the rejection of virus. The formation of cake clay on the membrane surface was the main cause of high rejection of colipbage T4 with MF of 0.22 μm.     

Photocatalytic degradation of trace-level of MicrocystinLR by nano-film of titanium dioxide

The occurrence of toxic water bloom of cyanobacte-ria algae, widely reported in eutrophic freshwater, hasbeen a serious pollution problem in recent years[1]. Mi-crocystins (MCs), the most common cyanobacteriatoxin with a cyclic heptapeptide structure (Fig…     

Underwater holmium-laser-pulse-induced complete cavitation bubble movements and acoustic transients

The complete evolution of holmium-laser-pulse-induced cavitation bubble movements and acoustic transients underwater are investigated experimentally. The laser was single fiber-guided and had a 300 mJ pulse energy and 300 μs pulse duration (full width at half-maximum). In our experiments, more than four oscillations and four acoustic transients were demonstrated. 272 μs after laser onset, the cavitation bubbles reached their maximum transverse and longitudinal lengths of 2046 and 1914 μm, respectively. The maximum transverse and longitudinal bubble wall velocities were 28.9 and 39.2 m/s at 560 and 528 μs after laser onset, respectively. This investigation will be helpful to make good use of cavitation effect in medical applications of holmium laser pulses.     

Photo-induced degradation of Ru（Ⅱ） complex absorbed on anatase TiO2 thin film electrode

Photo-induced degradation of a monolayer of Ru（Ⅱ） complex absorbed on anatase TiO2 thin film was studied by using resonant micro-Raman spectroscopy. Under intense light radiation of a laser and in the absence of a reducing agent, the dye decomposed quickly. When the dye-sensitized TiO2 thin film electrode was covered by a reducing agent, namely the I^-/I3^- redox couple, the photo-induced decomposing rate was slowed by a factor of -10^6. In both cases, the dye decomposed with time under an exponential law.     

Compositional change in human enamel irradiated with MIR free electron laser

The purpose of this study was to investigate compositional changes in human enamel irradiated with the free electron laser (FEL). The exposure on dental enamel at the wavelength of 9.64 μm was observed with the Beijing free electron laser. The distribution of elements in the irradiated or non-irradiated enamel was measured by scanning electron microscope (SEM) with energy-dispersive spectroscopy and synchrotron radiation X-ray fluorescence (SRXRF) in Beijing Synchrotron Radiation Facility (BSRF). The results showed that the P/Ca ratio in the ablation region of enamel at the maximum wavelength of infrared absorption was obviously smaller than that at the non-maximum wavelength. In the ablation region the ratios of P/Ca and Ca/Sr were smaller than those in the non-ablation region. The distributions of P, Ca and Sr in the ablation region were heterogeneous due to the element change caused by FEL irradiation.     

Preparation of protein-loaded microspheres with size≤10 μm by electrostatic droplet generation technology

AT PRESENT, ALMOST ALL PROTEIN DRUGS HAVE TO BE CLINI- CALLY ADMINISTERED VIA INJECTION ROUTES SUCH AS INTRAVE- NOUS INJECTION. ONE OF THE IMPORTANT PROBLEMS CON- FRONTED IS THAT THESE DRUGS SHOULD BE INJECTED REPEATEDLY DUE TO SHORT HALF-LIFE IN BLOOD. I…     

Simultaneous in-situ determination of U-Pb age and trace elements in zircon by LA-ICP-MS in 20 μm spot size

Simultaneous in-situ determination of U-Pb ages and 20 trace elements of three international zircon standards （91500, GJ1 and TEMORA 1） and one laboratory zircon standard （SK10-2） separated from Cenozoic fine-grained gabbro was carried out on quadrupole ICP-MS equipped with 193 nm excimer laser in 20 μm spot size. The weighted mean ^206Pb/^238U ages of 91500, GJ1 and TEMORA 1 are 1064.4±4.8 Ma （2σ）, 603.2±2.4 Ma （2σ） and 418.2±2.4 Ma （2σ）, respectively. The relative standard deviations （RSDs） of ^206Pb/^238U ages （2σ） are less than 2.2% for single measurements and 0.6% for weighted means. The obtained weighted mean ^206Pb/^238U ages of three standard zircons agree with the recommended values within 2σrerror. The weighted mean ^206Pb/^238U age of SK10-2 is 31.42=0.25 Ma （2σ） and the RSDs of ^206Pb/^238U ages （2σ） are between 2.4% and 5.7% for single measurements and less than 0.8% for weighted mean. The obtained weighted mean ^206Pb/^238U age is in good agreement with the age obtained by Yuan （2004）. Trace element concentrations of NIST612 and NIST614 obtained under the same LA-ICP-MS operating conditions agree with the recommended values within analytical error. The results indicate that it is possible to measure U-Pb age and trace elements simultaneously by LA-ICP-MS in a small spot size of 20μm.     

金刚石膜抛光表面缺陷对其红外透射率的影响

通过等离子体喷射CVD(chemical vapor deposition)方法生长了光学级金刚石厚膜,运用电火花和机械抛光技术对厚膜进行了双面抛光,并研究抛光表面缺陷对厚膜红外透射率的影响.结果表明:表面的台阶、孔洞、裂纹和沟槽等缺陷均会引起入射红外光波的散射和吸收,从而导致金刚石厚膜透射率的下降.表面的台阶、孔洞、裂纹和沟槽等缺陷厚膜的平均红外透射率分别为46.53%,62.56%,50.11%,58.26%.     

In situ simultaneous determination of trace elements, U-Pb and Lu-Hf isotopes in zircon and baddeleyite

This paper describes a combined method of simultaneously measuring U-Pb and Lu-Hf isotopes as well as trace elements in Phalaborwa baddeleyite and 91500, GJ-1, TEMORA-1 and SK10-2 zircons by means of Neptune MC-ICPMS and Agilent Q-ICPMS connected to a 193 nm excimer laser ablation system. Material ablated by laser was carried in different proportions into Q-ICPMS for U-Pb isotopic and trace elemental and MC-ICPMS for Lu-Hf isotopic compositions. Experiments indicate that different proportions of ablated material for the Q-ICPMS and MC-ICPMS （6：4, 5：5 and 4：6 respectively） do not show any bias for the zircon/baddeleyite U-Pb age, Lu-Hf isotope and trace elemental compositions within analytical errors. Using 40-60 μm spot size, the obtained U-Pb ages of Phalaborwa baddeleyite, 91500, GJ-1, TEMORA and SK10-2 zircons are 2065±15 （2σ, n=20）, 1063±6 （2σ, n=-19）, 613±6 （2σ, n=20）, 416±5 （2σ, n=20） and 32.6±0.5 （2σ, n=20） Ma, respectively. The ^176Hf/^177Hf ratios are 0.281231±24 （2SD, n=20）, 0.282310±35 （2SD, n=19）, 0.282028±34 （2SD, n=20）, 0.282687±34 （2SD, n=20） and 0.282752±53 （2SD, n=20）, respectively. The obtained trace elemental compositions are identical to the reference values. Therefore, this kind of technique makes it possible to simultaneously obtain the U-Pb age, Lu-Hf isotopes and trace elemental compositions of zircon and baddeleyite, which could be an important tool in solving problems in earth sciences.     

Preparation of porous microstructures on NiTi alloy surface with femtosecond laser pulses

Porous microstructures on Nickel-Titanium （NiTi） alloy surfaces were prepared by linearly polarized femtosecond lasers with moving focal point at a certain speed. It was found that various novel micro- structures from feather-like ripples to cluster-like porous textures could be formed with increasing laser energy. Particularly, when the laser energy was 400 llJ, a periodic porous metal surface was gen- erated. Measurement of X-ray diffraction showed that the grains on the sample surface were refined through femtosecond laser ablation processes, but the crystal structures still kept their original states. Analysis by X-ray photoelectron spectroscopy revealed that Ni/l＂i on the sample surface was changed with an evident oxidization of titanium element under different laser energies. This investigation pro- vides a new approach to improve the biocompatibility of NiTi-based implant devices.     

Discovery of the superlarge gallium ore deposit in Jungar, Inner Mongolia, North China

Gallium, Ge, V, and U are the associated valuable elements in coal. From the 1950s to the 1970s, some researchers in the departments of coal industry and mineral resources of China investigated these elements in coal during geological explorations. The enrichment mechanism and the environmental influence of trace elements in coal have been deeply studied in recent twenty years. With respect to the ore-forming theories and practical utilizations of metals in coal, germanium was furthest studi…