Effects of Yb^3＋ codoping on visible and near infrared emissions of Er^3＋-Yb^3＋ codoped Al2O3 powders by the sol-gel method

The 0.1 mol% Er^3＋ and 0-2 mol% Yb^3＋ codoped Al2O3 powders were prepared by the sol-gel method, and the phase structure, including only two crystalline types of doped Al2O3 phase, γ-（Al,Er, Yb）2O3 and θ-（Al,Er, Yb）2O3, was detected at the sintering temperature of 1000℃. The visible and near infrared emissions properties depended strongly on the Yb^3＋ codoping, and the corresponding maximal peak intensities centered at about 523, 545, 660 and 1533 nm were obtained respectively for the 0.1 mol% Er^3＋ and 0.5 mol% Yb^3＋ codoped Al2O3 powders, which were composed of θ-（Al,Er,Yb）2O3 and a small amount of γ-（Al,Er, Yb）2O3 phases. The two-photon absorption process was responsible for the visible up-conversion emissions, and the one-photon absorption process was involved in the near infrared emissions of the Er^3＋-yb^3＋ codoped Al2O3 powders.     

Up-conversion luminescence of Er^3＋ doped and Er^3＋/Yb^3＋ co-doped YTaO4

The synthesis and up-conversion luminescent properties of YTaO4：Er^3＋ and YTaO4：Er^3＋/Yb^3＋ are reported for the first time. According to the measurement results of up-conversion spectra, Yb^3＋ co-doping can remarkably enhance the green （^2H11/2/^4S3/2→^4I15/2） and red （^4F9/2→^4I15/2） emissions, but depress the infrared emission （^4I9/2→^4I15/2）. With the increase of the Yb^3＋ concentration, the intensity of green emission increases, after that, when the Yb^3＋ concentration increases continuously, the intensity of green emission decreases, while those of the red and infrared emissions increase and decrease alternately. In addition, the up-conversion mechanisms of Er^3＋ doped and Er^3＋/Yb^3＋ co-doped YTaO4 are also discussed. It is found that the transform of up-conversion mechanism from two-step energy transfer to cooperating sensitization takes place when Yb^3＋ concentration is increased up to 12 mol%. With the further increase of Yb^3＋ concentration, the energy-back-transfer gradually becomes the dominant up-conversion mechanism, which results in the quenching of the green emission and slight increasing of the red and infrared emissions.     

CO<Subscript>2</Subscript> gas emplacement age in the Songliao Basin: Insight from volcanic quartz <Superscript>40</Superscript>Ar-<Superscript>39</Superscript>Ar stepwise crushing

Due to a lack of suitable minerals, the gas/oil emplacement ages have never been accurately obtained before. CH₄-CO₂-saline- bearing secondary inclusions are found in quartz from the volcanic rocks of the Yingcheng Formation, the container rocks of the deep CO₂ gas reservoir in the Songliao Basin. The inclusion fluid was trapped into microcracks in quartz during the gas emplacement and accumulation, providing an optimal target for the ⁴⁰Ar-³⁹Ar stepwise crushing technique to determine the CO₂ gas emplacement age. ⁴⁰Ar-³⁹Ar dating results of a quartz sample by stepwise crushing yield a highly linear-regression isochron with an age of 78.4±1.3 Ma, indicating that the accumulation of the deep CO₂ gas reservoir in the Songliao Basin occurred in the late Cretaceous. This is the first time to report an exact isotopic age for a CO₂ gas reservoir, which indicates that the ⁴⁰Ar-³⁹Ar dating can serve as a new technique to date the oil/gas emplacement ages.     

Photoluminescence and cathodoluminescence properties of CaLaGa<Subscript>3</Subscript>O<Subscript>7</Subscript>:Eu<Superscript>3+</Superscript> phosphors

The CaLaGa₃O₇:Eu³⁺ phosphor was prepared by a chemical co-precipitation method. Field emission scanning electron microscopy (FE-SEM), laser particle size analysis, X-ray diffraction (XRD), photoluminescence (PL), and cathodoluminescence (CL) spectra were utilized to characterize the synthesized phosphor. The results revealed that the phosphor was composed of microspheres with a slight agglomerate phenomenon and was spherically shaped. The average grain size was about 1.0 μm. Eu³⁺ ions, as luminescent centers, substituted La³⁺ ions into the single crystal lattice of CaLaGa₃O₇ with the sites of C_s. Although the CL spectrum was greatly different from the PL spectrum, it had the strongest red emission corresponding to the ⁵D₀ →⁷F₂ transition of Eu³⁺. Under the excitation of UV light (287 nm) and electron beams (1.0–7.0 kV), the chromaticity coordinates of the phosphor were found to be in the nearly red and orange light regions, respectively.     

Al^3＋ -induced vesicle formation

Aluminium laurate [Al(OOCC11H23)3] was synthesized as a surfactant, which can dissolve in micellar solution of a zwitterionic surfactant, tetradecycldimethylamine oxide (C14DMAO). The phase behavior of the mixtures of Al(OOCC11H23)3 and C14DMAO in water was studied and birefringent Lα-phase was observed. The birefringent Lα-phase consists of vesicles that were demonstrated by Polarizer and Transmission Electron Microscope (TEM) micrographs. Al3 -coordinated vesicles could be used as templating-precursor, providing a vesicle-route for preparation of inorganic nanoscale particles.     

Nitric oxide suppresses stomatal opening by inhibiting inward-rectifying K<Stack><Subscript>in</Subscript><Superscript>+</Superscript></Stack> channels in <Emphasis Type="Italic">Arabidopsis</Emphasis> guard cells

We explore nitric oxide （NO） effect on K^＋in, channels in Arabidopsis guard cells. We observed NO inhibited K^＋in, currents when Ca^2＋ chelator EGTA （Ethylene glycol-bis（2-aminoethylether）-N,N,N′,N;tetraacetic acid） was not added in the pipette solution; K^＋in currents were not sensitive to NO when cytosolic Ca^2＋ was chelated by EGTA. NO inhibited the Arabidopsis stomatal opening, but when EGTA was added in the bath solution, inhibition effect of NO on stomatal opening vanished. Thus, it implies that NO elevates cytosolic Ca^2＋ by activating plasma membrane Ca^2＋ channels firstly, then inactivates K^＋in, chartnels, resulting in stomatal opening suppressed subsequently.     

Preparation and luminescence characteristics of Sr3SiO5：Eu^2＋ phosphor for white LED

The Sr3SiO5：Eu^2＋ phosphor was synthesized by high temperature solid-state reaction. The emission spectrum of Sr3SiO5：Eu^2＋ shows two bands centered at 487 and 575 nm, which well agree with the theoretic values of emission spectrum. The excitation spectrum for 575 nm emission center has several excitation bands at 365, 418, 458 and 473 nm. And the results show that the emission spectrum of Sr3SiO5：Eu^2＋ is influenced by the Eu^2＋ concentration. The relative emission spectra of the white-emitting InGaN-based YAG：Ce^3＋ LED and Sr3SiO5：Eu^2＋ LED were investigated. The results show that the color development of InGaN-based Sr3SiO5：Eu^2＋ is better than that of InGaN-based YAG：Ce^3＋, and the CIE chromaticity of InGaN-based Sr3SiO5：Eu^2＋ is （x=0.348, y=0.326）.     

I-doping of anodized TiO<Subscript>2</Subscript> nanotubes using an electrochemical method

In order to obtain TiO2 with high photocatalytic activity, a cathode reduction was used to dope I⁷⁺ and I⁵⁺ into TiO₂ nanotubes of anodized Ti in C₂H₂O₄•2H₂O + NH₄F electrolyte. SEM images show that the anodization method integrated the preparation with the doping process, which for nonmetals-doping is advantageous to maintain the morphological integrity of TiO₂ nanotubes. I⁷⁺-I⁵⁺-doping enhances the UV response of TiO₂ and result in a red-shift. Under UV/visible irradiation, a I⁷⁺-I⁵⁺-doped sample (400°C) showed the highest I_ph and photocatalytic efficiency. A part of I^– in the I⁷⁺-I⁵⁺-doped sample is involved in the UV response, the red-shift and the higher I_ph.     

Characteristics of Pb<Superscript>2+</Superscript> biosorption with aerobic granular biomass

Experimental studies were conducted on the feasibility of aerobic granular biomass as a novel type of biosorbent for Pb^2＋ removal. The results show that the initial pH, Pb^2＋ concentration （Co） and biomass concentration （X0） affected the biosorption process significantly. Both the Freundlich and Langmuir isotherm models describe the biosorption process accurately, with correlation coefficients of 0.932 and 0.959 respectively. The Pb^2＋ biosorpUon kinetics is interpreted as having two stages, with the second stage described reasonably well by a Lagergren pseudo-second order model. Moreover, the surface change of granular biomass after the Pb^2＋ biosorption process appears to be caused by ion exchange and metal chelation according to the analysis results of Environmental Scanning Electron Microscopy （ESEM） and Energy Dispersive X-ray Spectroscopy （EDX）.     

Photoluminescence and cathodoluminescence properties of a novel CaLaGa307：Dy3＋ phosphor

A single host white emitting phosphor, CaLaGa3O7:Dy3+, was synthesized by chemical co-precipitation. Field emission scanning electron microscopy, X-ray diffraction, laser particle size analysis, and photoluminescence and cathodoluminescence spectra were used to investigate the structural and optical properties of the phosphor. The phosphor particles were composed of microspheres with a slight tendency to agglomerate, and an average diameter was of about 1.0 μm. The Dy3+ ions acted as luminescent centers, and substituted La3+ ions in the single crystal lattice of CaLaGa3O7 where they were located in Cs sites. Under excitation with ultraviolet light and a low voltage electron beam, the CaLaGa3O7:Dy3+ phosphor exhibited the characteristic emission of Dy3+ (4F9/2-6H15/2 and 4F9/2-6H13/2 transitions) with intense yellow emission at about 573 nm. The chromaticity coordinates for the phosphor were in the white region. The relevant luminescence mechanisms of the phosphor are investigated. This phosphor may be applied in both field emission displays and white light-emitting diodes.     

Theoretical investigations of ESR and optical spectra of crystalline KHSO4：Mn^2＋

Calculations of d-d transitions and the axial zero-field splitting parameter D in crystalline KHSO4:Mn2+ have been undertaken, with consideration of the ninth O2– ligand. Energy level values calculated in a tetragonal field are in good agreement with experimentally observed values. Occasionally degenerate energy levels of 4A1(4Eg(G)) and 4A1(4A1g(G)) were found in the tetragonal crystal field. The calculated value of D is in good agreement with experimental value for KHSO4:Mn2+.     

Structural investigation and luminescent properties of BaZr(BO<Subscript>3</Subscript>)2:Eu<Superscript>3+</Superscript> phosphors containing Si

Si⁴⁺-doped BaZr(BO₃)₂:Eu³⁺ phosphors are prepared by a conventional solid-state reaction. The influence of Si⁴⁺ addition on the charge transfer state of Eu³⁺-O^2– and photoluminescence (PL) properties of BaZr(BO₃)₂:Eu³⁺ are discussed. Room temperature PL spectra indicated that efficient emission is obtained by Si doping. Increased values for the peak-peak ratio (PPR) of BaZr(BO₃)₂:Eu³⁺ at higher Si doping concentrations implied that the Eu³⁺ ion is located in a more asymmetric environment in BaZr_0.8Si_0.2(BO₃)₂:Eu³⁺ than in the undoped samples. The Judd-Ofelt parameters Ω_λ (λ=2,4) were calculated from the PL data, giving results that were consistent with those from the PPR. The maximum radiative quantum efficiency was achieved at a Si doping concentration of 20 mol%.     

Near-infrared to visible up-conversion emissions of Er^3＋ doped Al2O3 powders derived from the sol-gel method

The Er3 doped Al2O3 powders were prepared by the sol-gel method using the aluminium isopropoxide [Al(OC3H7)3]-derived Al2O3 sols with addition of the erbium nitrate [Er(NO3)3.5H2O]. The different phase structure, including three crystalline types of (Al,Er)2O3 phases, γ, θ, α, and two Er-Al-O phases, ErAlO3 and Al10Er6O24, was obtained with the 1 mol% Er3 doped Al2O3 powders at the different sintering temperatures of 600―1200℃. The green and red up-conversion emissions centered at about 523, 545 and 660 nm, corresponding respectively to the 2H11/2, 4S3/2→4I15/2 and 4F9/2→4I15/2 transitions of Er3 , were detected by a 978 nm semiconductor laser diodes excitation. The phase structure and OH content had evident influence on the up-conversion emissions intensity. The maximum intensities of both the green and red emissions were obtained respectively for the Er3 doped Al2O3 powders sintered at 1200 ℃, which was composed mainly of α-(Al,Er)2O3, less of ErAlO3 and Al10Er6O24 phases, and with the least OH content. The two-photon absorption up-conversion process was involved in the green and red up-conversion emissions of the Er3 doped Al2O3 powders.     

A magic eggshell: Cu<Superscript>2+</Superscript> reacts with S<Superscript>2−</Superscript> to produce metal Cu,rather than CuS

In common sense, the chemical reaction between Cu²⁺ and S^2– ions produces black precipitation of CuS. However, if they are separated by an eggshell, they produce copper with trace amount of CuS on the surface of the eggshell at the side of copper chloride solution within one week. Such an unexpected phenomenon strongly indicated that Cu²⁺ is able to be reduced into metal copper when S^2– diffuses throughout the porous eggshell. The produced copper was verified by reacting with nitric acid to generate red-brown nitrogen dioxide at ambient temperature, as well as by the powder X-ray diffraction (XRD) and energy dispersive analysis of X-rays (EDS).     

Extraction and separation of nickel and cobalt from saprolite laterite ore by microwave-assisted hydrothermal leaching and chemical deposition

Extraction and separation of nickel and cobalt from saprolite laterite ore were studied by using a method of microwave-assisted hydrothermal leaching and chemical deposition. The effects of leaching temperature and time on the extraction efficiencies of Ni2+ and Co2+ were investigated in detail under microwave conditions. It is shown that the extraction efficiencies of Ni2+ and Co2+ from the ore pre-roasted at 300℃ for 5 h were 89.19% and 61.89% when the leaching temperature and time were about 70℃ and 60 min, respectively. For the separation process of Ni and Co, the separation of main chemical components was performed by adjusting the pH values of sulfuric leaching solutions using a NaOH solution based on the different pH values of precipitation for metal hydroxides. The final separation efficiencies of Ni and Co were 77.29% and 65.87%, respectively. Furthermore, the separation efficiencies of Fe of 95.36% and Mg of 92.2% were also achieved at the same time.     

Resistless photochemical etching of a silicon wafer by UV laser with an H<Superscript>2</Superscript>O<Superscript>2</Superscript> and HF aqueous solution

A new resistless etching method has been developed for Silicon wafers. This new method uses an aqueous solution consisting of hydrogen peroxide (H₂O₂) and hydrogen fluoride (HF) as the activating etchants. A 193 nm ArF excimer laser and a 266 nm fourth harmonic generation Nd: YAG laser were used as the photon sources. Results showed that pattern etching has been achieved without any photoresist film. In the case of the 193 nm laser, the optimal etching appeared at a 1.3 H₂O₂÷HF ratio, where an etch depth of 210 nm was achieved with a fluence of 29 mJ/cm² and shot number of 10000. At the same conditions, the etch depth with H₂O₂ and HF solution was three times of that by using H₂O and HF mixture. In the case of the 266 nm Nd: YAG laser, the optimal etching appeared at twice ratio of H₂O₂/HF, where the etch depth of 420 nm was achieved with a fluence of 12 mJ/cm² and shot number of 30000. Results showed that the etch effect of the 266 nm Nd: YAG laser was more desirable than that of the 193 nm ArF excimer laser.     

Preparation and upconversion luminescence of YVO<Subscript>4</Subscript>:Er<Subscript>3+</Subscript>, Yb<Subscript>3+</Subscript>

YVO₄:Er³⁺, Yb³⁺ with varying Yb³⁺ concentrations were prepared by a precipitation method. The results of X-ray diffraction (XRD) show that all the samples have a tetragonal zircon structure; the calculated average crystallite sizes are in the range of 14–22 nm. The lattice constants and cell volume of the samples decrease slightly with the increase in Yb³⁺ concentration. The upconversion luminescence spectra of all the samples were studied under 980 nm laser excitation. The strong green emission is observed, which is attributed to the ²H_11/2 → ⁴I_15/2 and ⁴S_3/2→⁴I_15/2 transitions of Er³⁺, and the red emission peaks in 650–675 nm can be ignored. The emission intensity for the sample depends on the Yb³⁺ concentration. These results reveal that the upconversion processes of YVO₄:Er³⁺, Yb³⁺ are related to the structure and the doping Yb³⁺ concentration of the sample.     

Resonance-enhanced multiphoton ionization spectroscopy on the B′2Σ+ and B2Π states of NS

Resonance-enhanced multiphoton ionization （REMPI） spectra of N^32S and N^34S have been recorded in the range of 35700-40200 cm^-1. The radical was generated by a pulsed dc discharge of a mixture of SF6 and N2 under a supersonic free jet condition. All the 16 observed bands of N^32S radicals have been assigned, among which 12 bands belong to three transition progressions （v′=0-4, 0）, （v′=1-4, 1） and （v′=2-4, 2） from the X^2П ground state to the B′^2∑^＋ upper state and the rest correspond to （9, 0）, （10, 0）, （11, 0） and （12, 0） bands of B^2П-X^2П transition, respectively. Analysis of the rotationally resolved spectra yields exhaustive spectroscopic constants of both the X^2П ground state and the B′^2∑^＋ excited state. The electronic transition bands of the isotopic molecule N^34S have been rotationally analyzed for the first time and the rotational constants of the ground and upper states have been determined simultaneously.     

Preparation of Zn-doped TiO2 nanotubes electrode and its application in pentachlorophenol photoelectrocatalytic degradation

Zn-doped titanium oxide （TiO2） nanotubes electrode was prepared on a titanium plate by direct anodic oxidation and immersing method in sequence. Field emission scanning electron microscopy （FESEM） showed that the Zn-doped TiO2 nanotubes were well aligned and organized into high density uniform arrays with diameter ranging from 50 to 90 nm. The length and the thickness were about 200 and 15 nm respectively. TiO2 anatase phase was identified by X-ray diffraction （XRD）. X-ray photoelectronspectroscopy （XPS） indicated that Zn ions were mainly located on the surface of TiO2 nanotubes in form of ZnO clusters. Compared with TiO2 nanotubes electrode, about 20 nm red shift in the spectrum of UV-vis absorption was observed. The degradation of pentachlorophenol （PCP） in aqueous solution under the same condition （initial concentration of PCP： 20 mg/L; concentration of Na2SO4：0.01 mol/L and pH： 7.03） was carried out using Zn-doped TiO2 nanotubes electrode and TiO2 nanotubes electrode. The degradation rates of PCP using Zn-doped TiO2 nanotubes electrode were found to be twice and 5.8 times as high as that using TiO2 nanotubes electrode by UV radiation （400 μw/cm^2） and visible light radiation （4500 μw/cm^2）, respectively. 73.5% of PCP was removed using Zn-doped TiO2 nanotubes electrode against 45.5% removed using TiO2 nanotubes electrode in 120 min under UV radiation. While under visible light radiation, the degradation efficiency of PCP was 18.4% using Zn-doped TiO2 nanotubes electrode against 3.2% using TiO2 nanotubes electrode in 120 min. The optimum concentration of Zn doping was found to be 0.909%. The PCP degradation efficiencies of the 10 repeated experiments by Zn-doped TiO2 nanotubes electrode were rather stable with the deviation within 3.0%.     

Temperature effect on the corrosion and passivation characterization of Ni<Subscript>82.3</Subscript>Cr<Subscript>7</Subscript>Fe<Subscript>3</Subscript>Si<Subscript>4.5</Subscript>B<Subscript>3.2</Subscript> alloy in acidic media

The effects of temperature on corrosion and the electrochemical behavior of Ni_82.3Cr₇Fe₃Si_4.5B_3.2 glassy alloy in HCl, H₂SO₄, and H₃PO₄ acids were studied using AC and DC techniques. Impedance data reveal that the susceptibility to localized corrosion increases with increasing temperature. Potentiodynamic polarization curves reveal that the bulk glassy alloy is spontaneously passivated at all the investigated temperature in H₂SO₄ and H₃PO₄ solutions. A localized corrosion effect in HCl solution is clearly observed. The apparent activation energies in the regions of Tafel, active, and passive, as well as the enthalpies and entropies of the dissolution process were determined and discussed. The high apparent activation energy (E_a) value for H₃PO₄ solution in Tafel region is explained by the low aggressivity of PO₄3- ions.