Resistless photochemical etching of a silicon wafer by UV laser with an H2O2 and HF aqueous solution

A new resistless etching method has been developed for Silicon wafers. This new method uses an aqueous solution consisting of hydrogen peroxide (H2O2) and hydrogen fluoride (HF) as the activating etchants. A 193 nm ArF excimer laser and a 266 nm fourth harmonic generation Nd:YAG laser were used as the photon sources. Results showed that pattern etching has been achieved without any photoresist film. In the case of the 193 nm laser, the optimal etching appeared at a 1.3 H2O2/HF ratio, where an etch depth of 210 nm was achieved with a fluence of 29 mJ/cm2 and shot number of 10000. At the same conditions, the etch depth with H2O2 and HF solution was three times of that by using H2O and HF mixture. In the case of the 266 nm Nd:YAG laser, the optimal etching appeared at twice ratio of H2O2/HF, where the etch depth of 420 nm was achieved with a fluence of 12 mJ/cm2 and shot number of 30000. Results showed that the etch effect of the 266 nm Nd: YAG laser was more desirable than that of the 193 nm ArF excimer laser.``Keyords: UV laser, resistless photochemical etching, hydrogen peroxide (H2O2).     

Preparation and luminescence characteristics of Sr3SiO5：Eu^2＋ phosphor for white LED

The Sr3SiO5：Eu^2＋ phosphor was synthesized by high temperature solid-state reaction. The emission spectrum of Sr3SiO5：Eu^2＋ shows two bands centered at 487 and 575 nm, which well agree with the theoretic values of emission spectrum. The excitation spectrum for 575 nm emission center has several excitation bands at 365, 418, 458 and 473 nm. And the results show that the emission spectrum of Sr3SiO5：Eu^2＋ is influenced by the Eu^2＋ concentration. The relative emission spectra of the white-emitting InGaN-based YAG：Ce^3＋ LED and Sr3SiO5：Eu^2＋ LED were investigated. The results show that the color development of InGaN-based Sr3SiO5：Eu^2＋ is better than that of InGaN-based YAG：Ce^3＋, and the CIE chromaticity of InGaN-based Sr3SiO5：Eu^2＋ is （x=0.348, y=0.326）.     

Effects of Yb^3＋ codoping on visible and near infrared emissions of Er^3＋-Yb^3＋ codoped Al2O3 powders by the sol-gel method

The 0.1 mol% Er^3＋ and 0-2 mol% Yb^3＋ codoped Al2O3 powders were prepared by the sol-gel method, and the phase structure, including only two crystalline types of doped Al2O3 phase, γ-（Al,Er, Yb）2O3 and θ-（Al,Er, Yb）2O3, was detected at the sintering temperature of 1000℃. The visible and near infrared emissions properties depended strongly on the Yb^3＋ codoping, and the corresponding maximal peak intensities centered at about 523, 545, 660 and 1533 nm were obtained respectively for the 0.1 mol% Er^3＋ and 0.5 mol% Yb^3＋ codoped Al2O3 powders, which were composed of θ-（Al,Er,Yb）2O3 and a small amount of γ-（Al,Er, Yb）2O3 phases. The two-photon absorption process was responsible for the visible up-conversion emissions, and the one-photon absorption process was involved in the near infrared emissions of the Er^3＋-yb^3＋ codoped Al2O3 powders.     

Near-infrared to visible up-conversion emissions of Er^3＋ doped Al2O3 powders derived from the sol-gel method

The Er3 doped Al2O3 powders were prepared by the sol-gel method using the aluminium isopropoxide [Al(OC3H7)3]-derived Al2O3 sols with addition of the erbium nitrate [Er(NO3)3.5H2O]. The different phase structure, including three crystalline types of (Al,Er)2O3 phases, γ, θ, α, and two Er-Al-O phases, ErAlO3 and Al10Er6O24, was obtained with the 1 mol% Er3 doped Al2O3 powders at the different sintering temperatures of 600―1200℃. The green and red up-conversion emissions centered at about 523, 545 and 660 nm, corresponding respectively to the 2H11/2, 4S3/2→4I15/2 and 4F9/2→4I15/2 transitions of Er3 , were detected by a 978 nm semiconductor laser diodes excitation. The phase structure and OH content had evident influence on the up-conversion emissions intensity. The maximum intensities of both the green and red emissions were obtained respectively for the Er3 doped Al2O3 powders sintered at 1200 ℃, which was composed mainly of α-(Al,Er)2O3, less of ErAlO3 and Al10Er6O24 phases, and with the least OH content. The two-photon absorption up-conversion process was involved in the green and red up-conversion emissions of the Er3 doped Al2O3 powders.     

Synthesis and modification of well-ordered layered cathode oxide LiNi<Subscript>2/3</Subscript>Mn<Subscript>1/3</Subscript>O<Subscript>2</Subscript>

Oxalic-acid-based co-precipitation method was employed to prepare LiNi_2/3Mn_1/3O₂ sample with a high-ordered structure. Li⁺, Ni²⁺ and Mn²⁺ acetates were used as starting materials. The influence of the amount of lithium source in the starting materials on Li⁺ content, disorder of Li⁺-Ni²⁺ ions, and electrochemical performance has been investigated. Rietveld refinement shows that the sample prepared with 20% excess Li-source in the starting materials exhibits a perfect ordered structure. A specific discharge capacity is as high as 172 mAh/g at C/20 in the voltage range of 4.35–2.7 V. However, the cyclability is not satisfactory: about 25.3% fade in capacity was observed over 50 cycles. Chemically stable SiO2 was coated on the surface of LiNi_2/3Mn_1/3O₂ particles. A significant improvement in cyclability was attained with 3 wt% SiO2 coating, which is ascribable to the protection of LiNi_2/3Mn_1/3O₂ particles from being dissolved into the electrolyte.     

CO<Subscript>2</Subscript> gas emplacement age in the Songliao Basin: Insight from volcanic quartz <Superscript>40</Superscript>Ar-<Superscript>39</Superscript>Ar stepwise crushing

Due to a lack of suitable minerals, the gas/oil emplacement ages have never been accurately obtained before. CH₄-CO₂-saline- bearing secondary inclusions are found in quartz from the volcanic rocks of the Yingcheng Formation, the container rocks of the deep CO₂ gas reservoir in the Songliao Basin. The inclusion fluid was trapped into microcracks in quartz during the gas emplacement and accumulation, providing an optimal target for the ⁴⁰Ar-³⁹Ar stepwise crushing technique to determine the CO₂ gas emplacement age. ⁴⁰Ar-³⁹Ar dating results of a quartz sample by stepwise crushing yield a highly linear-regression isochron with an age of 78.4±1.3 Ma, indicating that the accumulation of the deep CO₂ gas reservoir in the Songliao Basin occurred in the late Cretaceous. This is the first time to report an exact isotopic age for a CO₂ gas reservoir, which indicates that the ⁴⁰Ar-³⁹Ar dating can serve as a new technique to date the oil/gas emplacement ages.     

I-doping of anodized TiO<Subscript>2</Subscript> nanotubes using an electrochemical method

In order to obtain TiO2 with high photocatalytic activity, a cathode reduction was used to dope I⁷⁺ and I⁵⁺ into TiO₂ nanotubes of anodized Ti in C₂H₂O₄•2H₂O + NH₄F electrolyte. SEM images show that the anodization method integrated the preparation with the doping process, which for nonmetals-doping is advantageous to maintain the morphological integrity of TiO₂ nanotubes. I⁷⁺-I⁵⁺-doping enhances the UV response of TiO₂ and result in a red-shift. Under UV/visible irradiation, a I⁷⁺-I⁵⁺-doped sample (400°C) showed the highest I_ph and photocatalytic efficiency. A part of I^– in the I⁷⁺-I⁵⁺-doped sample is involved in the UV response, the red-shift and the higher I_ph.     

Kinetic studies of the decomposition reaction of adducts of dinuclear Fe(Ⅱ)/O2

Kinetic studies of the decomposition reaction of dinuclear Fe(Ⅱ) adducts [Fe₂(N-Et-HPTB){O₂P(OPh)₂}](Cl- O₄)₂ (1) and [Fe₂(N-Et-HPTB) {O₂P(Ph)₂}] (ClO₄)₂ (2) with O₂ have been carried out at low temperature using UV-vis spectra. The decomposition reaction of Fe(Ⅱ)/O₂ adducts was first-order in the experimental conditions, and the activation parameters were obtained. ?H^¹ = 85.62 kJ·mol^-1, ?S¹ = 19.43 J·mol^-1·K^-1 for compound (1) and ?H^¹ = 97.97 kJ·mol^-1, ?S^¹ = 55.68 J·mol^-1·K^-1 for compound (2). These results are similar to those of dioxygen adducts of other metals complexes and natural enzymes such as methane mono- oxygenase (MMOH).     

Investigation of the cross-reaction mechanism of C<Subscript>6</Subscript>H<Subscript>5</Subscript>F-HNO<Subscript>2</Subscript> aqueous solution irradiated at 355 nm by transient absorbance spectrum technique

The transient absorption spectrum technique was employed to investigate the cross-reaction mechanism of C6H5F-HNO2 aqueous solution irradiated at 355 nm. The characteristic and the kinetic parameters of transient species were also detected. Hydroxyl radical derived from the photolysis of HNO2 was added to monofluorobenzene with a second-order rate constant of （5.83±0.17）×10^9 L·mol^-1·s^-1 to form an adduct, C6H5F…OH, which was able to react with HNO2 as the main reaction pathway with a rate constant of （8.3±0.1）×10^7 L·mol^-1·s^-1. The C6F6…OH adduct can also be decayed by elimination of H2O to yield monofluorophenyl radical C6H4F-. By GC-MS technique, the final products were identified to be monofluorophenol, nitro-monofluorobenzene, nitro-monofluorophenol and para-fluorobiphenyl.     

Photoluminescence and cathodoluminescence properties of a novel CaLaGa307：Dy3＋ phosphor

A single host white emitting phosphor, CaLaGa3O7:Dy3+, was synthesized by chemical co-precipitation. Field emission scanning electron microscopy, X-ray diffraction, laser particle size analysis, and photoluminescence and cathodoluminescence spectra were used to investigate the structural and optical properties of the phosphor. The phosphor particles were composed of microspheres with a slight tendency to agglomerate, and an average diameter was of about 1.0 μm. The Dy3+ ions acted as luminescent centers, and substituted La3+ ions in the single crystal lattice of CaLaGa3O7 where they were located in Cs sites. Under excitation with ultraviolet light and a low voltage electron beam, the CaLaGa3O7:Dy3+ phosphor exhibited the characteristic emission of Dy3+ (4F9/2-6H15/2 and 4F9/2-6H13/2 transitions) with intense yellow emission at about 573 nm. The chromaticity coordinates for the phosphor were in the white region. The relevant luminescence mechanisms of the phosphor are investigated. This phosphor may be applied in both field emission displays and white light-emitting diodes.     

Nitric oxide suppresses stomatal opening by inhibiting inward-rectifying K<Stack><Subscript>in</Subscript><Superscript>+</Superscript></Stack> channels in <Emphasis Type="Italic">Arabidopsis</Emphasis> guard cells

We explore nitric oxide （NO） effect on K^＋in, channels in Arabidopsis guard cells. We observed NO inhibited K^＋in, currents when Ca^2＋ chelator EGTA （Ethylene glycol-bis（2-aminoethylether）-N,N,N′,N;tetraacetic acid） was not added in the pipette solution; K^＋in currents were not sensitive to NO when cytosolic Ca^2＋ was chelated by EGTA. NO inhibited the Arabidopsis stomatal opening, but when EGTA was added in the bath solution, inhibition effect of NO on stomatal opening vanished. Thus, it implies that NO elevates cytosolic Ca^2＋ by activating plasma membrane Ca^2＋ channels firstly, then inactivates K^＋in, chartnels, resulting in stomatal opening suppressed subsequently.     

Lasing on pyroclastic rocks: A case study of <Superscript>40</Superscript>Ar/<Superscript>39</Superscript>Ar dating on Moshishan Group,eastern Zhejiang Province

It is difficult to date pyroclastic rocks, for almost all the dating methods, due to the multiple sources during their formation. ^40Ar/^39gAr incremental heating results on groundmass selected from the samples show that the age spectra are meaningless geologically. However, singe crystal total fusions of CO2 lasing on the sanidine separates could yield rational 4^40Ar/^39Ar results and distinguish their sources in this study. Timing on three formations of the Moshishan Group, after avoiding the exotic and altered grains by lasing on the single sanidine separate, was reported in this paper. The lowermost portion of the Chawan Formation gives an age of 113.7±0.3 Ma; the lower part of the Xishantou Formation was formed 116.4±0.4 Ma ago and the bottom of the Gaowu Formation took its shape at 118.4±0.4 Ma. These new ages are much younger than the previous ones, suggesting that these thick volcanic formations had been formed in very short durations.     

Nonlinear optical properties of Eu<Subscript>2</Subscript>O<Subscript>3</Subscript> doped 5ZnO-20Nb<Subscript>2</Subscript>O<Subscript>5</Subscript>-75TeO<Subscript>2</Subscript> glasses

The third-order optical nonlinearities, including third-order nonlinear susceptibility X^(3), nonlinear refractive index (n2) and temporal response, were measured with forward DFWM using Nd:YAG mode-locked pulse laser. The results show that Eu203 doped 5ZnO-20Nb2O5-75TeO2 glasses have large n2 and ultra-fast temporal response. Raman spectra show that Eu2O3 dopant induces the changes in the local structure of glasses. The higher the dopant concentration, the larger the nonlinear refractive n2 and the faster the temporal response. The enhancement on the third-order optical nonlinearities can be attributed to the deformation of the electronic clouds in [TeO4] enhanced by Eu2O3 dopant.     

Photoluminescence and cathodoluminescence properties of CaLaGa<Subscript>3</Subscript>O<Subscript>7</Subscript>:Eu<Superscript>3+</Superscript> phosphors

The CaLaGa₃O₇:Eu³⁺ phosphor was prepared by a chemical co-precipitation method. Field emission scanning electron microscopy (FE-SEM), laser particle size analysis, X-ray diffraction (XRD), photoluminescence (PL), and cathodoluminescence (CL) spectra were utilized to characterize the synthesized phosphor. The results revealed that the phosphor was composed of microspheres with a slight agglomerate phenomenon and was spherically shaped. The average grain size was about 1.0 μm. Eu³⁺ ions, as luminescent centers, substituted La³⁺ ions into the single crystal lattice of CaLaGa₃O₇ with the sites of C_s. Although the CL spectrum was greatly different from the PL spectrum, it had the strongest red emission corresponding to the ⁵D₀ →⁷F₂ transition of Eu³⁺. Under the excitation of UV light (287 nm) and electron beams (1.0–7.0 kV), the chromaticity coordinates of the phosphor were found to be in the nearly red and orange light regions, respectively.     

Degradation of 2, 4-D acid using Mn2+ as catalyst under UV irradiation

In this paper, the oxidative degradation of 2, 4-dichlorophenoxyacetic acid (2, 4-D) using Mn²⁺/H₂O₂ reagent under UV irradiation was studied. The results show that 2, 4-D was degraded more completely in Mn²⁺/H₂O₂ solution than traditional Fenton solutions. The effects of the concentration of Mn²⁺, H₂O₂ and pH were also investigated. And under the optimal condition of 1.48×10⁻⁴ mol/L, 8.99×10⁻⁵ mol/L and pH 3.38, the formation of ·OH was the most, both the decomposition rate of H₂O₂ and the degradation rate of 2, 4-D were the fastest. In addition, the photoreaction process was monitored using spin-trapping electron paramagnetic resonance (EPR), and the results indicated that the oxidative process was predominated mainly by the hydroxyl radical (·OH) gennerated in the system. Biography: HUANG Yingping (1964–), Professor, Ph. D., research direction: pollution ecology and water pollution control.     

Growth characteristics of directionally solidified Al<Subscript>2</Subscript>O<Subscript>3</Subscript>/YAG/ZrO<Subscript>2</Subscript> ternary hypereutectic <Emphasis Type="Italic">in situ</Emphasis> composites under ultra-high temperature gradient

Oxide eutectic ceramic in situ composites have attracted significant interest in the application of high-temperature structural materials because of their excellent high-temperature strength, oxidation and creep resistance, as well as outstanding microstructural stability. The directionally solidified ternary Al₂O₃/YAG/ZrO₂ hypereutectic in situ composite was successfully prepared by a laser zone remelting method, aiming to investigate the growth characteristic under ultra-high temperature gradient. The microstructures and phase composition of the as-solidified hypereutectic were characterized by using scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), and X-ray diffraction (XRD). The results show that the composite presents a typical hypereutectic lamellar microstructure consisting of fine Al₂O₃ and YAG phases, and the enriched ZrO₂ phases with smaller sizes are randomly distributed at the Al₂O₃/YAG interface and in Al₂O₃ phases. Laser power and scanning rate strongly affect the sample quality and microstructure characteristic. Additionally, coarse colony microstructures were also observed, and their formation and the effect of temperature gradient on the microstructure were discussed.     

Theoretical study on the lithium bond interaction of furan homologues C4H4Y （Y=O,S） with LiCH3 via DFT and MP2

The optimizations geometries and interaction energy corrected by BSSE of the complexes between C4H4Y （Y=O, S） and CHiLi have been calculated at the B3LYP/6-311＋＋G^＊＊ and MP2/6-311＋＋G^＊＊ levels. Three complexes were obtained. Abnormally, the calculations showed that all the C10--Li14 bond lengths increased obviously but the blue-shift of C10-Li14 stretching frequency occurred after formed complexes. The calculated binding energy with basis set super-position error （BSSE） and zero-point vibrational energy corrections of complexes I-III is -45.757, -35.700 and -39.107 kJ·mol^-1, respectively. The analyses on the combining interaction with the atom-in-molecules theory （AIM） also showed that a relatively strong lithium bond interaction presented in furan homologues C4H4Y-LiCH3 systems. Natural bond orbital theory （NBO） analysis has been performed, and the results revealed that the complex I is formed with n-σ type lithium bond interaction between C4H40 and LiCH3, complex II is formed with TT-s type lithium bond interaction between C4H4O and LiCH3, and complex III is formed with TT-s and n-s type lithium bond interactions between C4H4S and LiCH3, respectively.     

In situ Nd isotopic measurement of natural geological materials by LA-MC-ICPMS

Using newly determined Sm isotopic abundances for correcting the isobaric interference of ^144Sm on ^144Nd and the established mass bias relationship between Sm and Nd, a series of in situ Nd isotopic measurements were conducted for relatively high Nd concentrations of natural geological materials, including apatite, titanite, monazite and perovskite on a Neptune multi-collector inductively coupled plasma mass spectrometry （MC-ICPMS）, coupled to a 193 nm ArF excimer laser ablation system. The results show that Ce has no significant influence on the precision and accuracy of Nd isotopic analyses for LREE-enriched geological minerals and that our approach is efficient in obtaining reliable ^143Nd/^144Nd and ^147Sm/^144Nd ratios for those materials with Sm/Nd〈1（^147Sm/^144Nd〈0.6）. When combined with trace element and U-Pb isotope data, the in situ Nd isotopic data can provide important information on geological processes.     

Stabilization of mini-Nd: YVO4 laser using I2 hyperfine transition

By using a diode-pumped Nd:YVO₄ / KTP intracavity frequency-doubling mini-laser and frequency modulation optical heterodyne spectroscopy, we have obtained spectrum of¹²⁷I₂ hyperfine structure near 532 nm. The laser frequency is locked to hyperfine transitions of I₂. The analysis of error servo signal demonstrates that the laser frequency stability can reach 10⁻¹² at 1 second average time.     

Synthesis, Characterization and Calorimetry of Ni（C4H8N2O3）2Cl2

A coordination complex was synthesized from NiCl2 and dipeptide glycylglycine（GG）. It was characterized by element analysis, NMR and TG methods, and then was determined to be Ni（C4HsN2O3）2Cl2. Using an isoperibolic reaction calorimeter, the standard molar enthalpy of formation of Ni（GG）2Cl2（solid） has been determined to be -（1 674.66±2.02） kJ · mol^-1 at 298.15 K.