Photovoltaic properties of MEH-PPV/TiO2 nanocomposites

Photovoltaic properties of photodiodes based on nano-TiO2 and poly[2-methoxy,5-（2＇-ethlhexyloxy）-p-phenylenevinylene] （MEH-PPV） composites are investigated. By comparing composite devices with the same weight of TiO2 （nanoparticles and nanotubes）：MEH-PPV, it was found that the device with TiO2 nanotubes exhibited better performance. By further optimizing the weight radio of TiO2 nanotubes： MEH-PPV, we gained the device with a short circuit current density of 9.27μA/cm^2 with a light intensity of 16.7mW/cm^2 at the 500 nm wavelength, the highest open-circuit voltage of 1.1V, and a photosensitivity of 332 at reverse bias of -0.6V. The photosensitivity is improved by a factor of 33 compared with the undoped MEH-PPV device.     

CoFe2O4/SiO2纳米复合材料的制备及其磁性

采用溶胶-凝胶法制备（CoFe₂O₄）_x/（SiO₂）_1-x纳米复合材料. 利用X射线衍射（XRD）和振动样品磁强计（VSM）研究样品结构、 晶粒尺寸及磁性. 结果表明, 随SiO₂含量增加, 样品的晶粒尺寸减小, 比饱和磁化强度和矫顽力降低.      

Preparation and performance of LiNi0. 8Co0.2O2 cathode material based on Co-substituted α-Ni（OH）2 precursor

Co-substituted α-Ni（OH）2 was synthesized by a novel microwave homogeneous precipitation method in the presence of urea. LiNi0.8Co0.2O2 cathode material was synthesized by calcining Co-substituted α-Ni（OH）2 precursor and LiOH·H2O at 900℃for 10 h in flowing oxygen. XRD, FTIR, FESEM and electrochemical tests were used to study the physical and the electrochemical performances of the materials. The results show that the prepared LiNi0.8Co0.2O2 compound has a good layered hexagonal structure. Moreover, the LiNi0.8Co0.2O2cathode material demonstrates stable cyclability with a high initial specific discharge capacity of 183.9 mAh/g. The good electrochemical performance could be attributed to the uniform distribution of Ni^2＋ and Co^2＋ ions in the crystal structure and a minimal cation mixing in LiNi0.8Co0.2O2 host structure.     

Modification of TiO2 nanotubes arrays by CdS and their photoelectrocatalytic hydrogen generation properties

In order to realize hydrogen generation under visible light, novel CdS/TiO2 nanotubes arrays are developed by electrochemical anodizaUon of Ti in 0.15 mol/L NHTF ＋ 0.08 mol/L H2C2O4 electrolyte. The diameter of the nanotube is 80-100 nm and the length is approximately 550 nm. The CdS nano-particles are deposited on the TiO2 nanotubes arrays by chemical bath deposition （CBD） in the ammonia-thiourea system. A 300 W Xe lamp is used as the light source, CdS/TiO2 nanotube arrays are used as the photoanode with the application of 1.0 V bath voltage, and 0.1 mol/L Na2S ＋ 0.04 mol/L Na2SO3 solution is used as the electrolyte, then the rate of photoelectrocatalytic hydrogen generation is 245.4 μL/（h·cm^2）. This opens new perspectives for photoelectrocatalytic hydrogen generation by using CdS/TiO2 nanotubes arrays.     

Comparison between P25 and anatase-based TiO<Subscript>2</Subscript> quasi-solid state dye sensitized solar cells

Pure anatase TiO2 films have been made via hydration of titanium isopropoxide using a sol-gel tech-nique, while mixed TiO2 films which contained both anatase and rutile TiO2 were made from commercial P25 powder. Quasi-solid state dye-sensitized solar cells were fabricated with these two kinds of mesoporous films and a comparison study was carried out. The result showed that the open-circuit photovoltages （Voc） for both kinds of cells were essentially the same, whereas the short-circuit photo-currents （1sc） of the anatase-based cells were about 33% higher than that of the P25-based cells. The highest photocurrent intensity of the anatase-based cell was 6.12 mA/cm^2 and that of the P25-based cell was 4.60 mA/cm^2. Under an illumination with the light intensity of 30 mW/cm^2, the corresponding energy conversion efficiency was measured to be 7.07% and 6.89% for anatase-based cells and P25-based cells, respectively.     

The comparison of Cu（ll） adsorption capability of baker＇s yeast,nano-titania and their composite adsorbent

The anatase nano-TiO2 powder, with crystal size between 40 and 80 nm, was prepared by the liquid phase hydrolysis of TiCI4. At the same time, the nano-TiO2 was utilized with the baker＇s yeast biomass as a composite adsorbent to adsorb the Cu ions in the artificial aqueous solution. The investigation showed that the composite adsorbent had a fine adsorption efficiency. The TiO2 in the composite adsorbent could cooperate well with baker＇s yeast to improve the adsorbing capability of Cu^2＋ under the following experimental conditions as well： a quantity of composite adsorbent of 5 g·L^-1, pH≥4.0, an adsorption time of 40 min and an initial concentration of Cu ions of 10 mg·L^-1. In addition, the results of measurements, obtained with a scanning electron microscope, an infrared spectrophotometer and a Zeta potential analyzer, revealed that the baker＇s yeast and nano-TiO2 produced the composite adsorbent through coordination and hydrogen bonds in particular, etc. The stability of the composite adsorbent and the amount of titania loaded were largely dependent on the concentration of hydrogen ion in the solution.     

An in-situ DRIFTS study in the reaction between NO x and soot on BaAl2O4

The interactions between NO, O2 and their mixture on BaAl2O4, as well as the reaction of NOx with soot in the presence of O2, have been investigated using Diffuse Reflectance Infrared Fourier Transform Spectroscopy （DRIFTS）. NO adsorption produces only nitrites species in the absence of O2. NO2 adsorption produces nitrates species besides nitrites species. The produced nitrites will further react with O2, Osurf^-. and Olattice^2- to form nitrates. The reaction of NOx with soot begins with the reaction of nitrates with soot oxygenated complex （C（O））, which is regarded as the key and rate determining step. A reaction pathway is proposed for the catalyzed reaction of NOx with soot in the presence of O2.     

Fe_2O_3/TiO_2复合纳米管阵列的制备及其可见光催化性能研究

在氟化铵-乙二醇体系中,采用阳极氧化法在铁基体上制备Fe_2O_3纳米管阵列,然后以氟钛酸铵为钛源,利用水热法在Fe_2O_3纳米管阵列上负载TiO_2纳米片,制得Fe_2O_3/TiO_2复合纳米管阵列,利用SEM、EDS、XRD、TEM、UV-Vis等手段,对所制Fe_2O_3/TiO_2纳米管阵列的表面形貌、物相结构及光催化性能进行表征,并分析Fe_2O_3/TiO_2纳米结构对亚甲基蓝的可见光降解能力。结果表明,Fe_2O_3/TiO_2复合纳米管阵列具有良好的可见光响应;NH_4F浓度为0.4%、水热反应3h制备的Fe_2O_3/TiO_2复合结构具有最佳的光催化性能,对亚甲基蓝的降解率可达90%。     

Dielectric properties of low dielectric constant Ba0.60Sr0.40Mg0.15Ti0.85O3-Mg2TiO4 composite thin films for tunable applications

Ba0.60Sr0.40Mg0.15Ti0.85O3-xmol%Mg2TiO4 （x = 0-40 mol%） （BSTM-MT） composite thin films were fabricated by sol-gel method. The precursor solution of these composite thin films was prepared through mixing the Ba0.80Sr0.40Mg0.15Ti0.85O3 and Mg2TiO4 solution. The microstructures and dielectric tunability of composite thin films were investigated. The dielectric constant of composite thin films can be tailored from 155 to 55 by changing the concentration of Mg2TiO4. The dielectric loss of these composite thin films were still kept below 0.01 and the tunability was above 20% at a dc-applied electric field of 500 kV/cm. Suitable dielectric constant, low dielectric loss, and high tunability of this kind of composite thin films can be useful for potential microwave tunable applications.     

水热体系下二氧化钛与氧化石墨烯复合纳米晶的合成

 200 ℃下四方结构的二氧化钛(TiO2)与氧化石墨烯(GO)复合纳米晶在一个装有适量钛酸四丁酯、无水乙醇、氧化石墨烯和蒸馏水的密闭的水热釜中加热12 h后被制备。X射线粉末衍射仪（XRD)、扫描电子显微镜（SEM）、透射电子显微镜（TEM）等一系列分析仪器被运用来揭示二氧化钛与氧化石墨烯复合纳米晶是由粒径大约160 nm的四方结构的二氧化钛纳米晶与氧化石墨烯复合而成,通过紫外吸收对其光学性能进行了必要的测试。
     

Direct electrochemistry and electrocatalysis of horseradish peroxidase in MnO2 nanosheet film

A novel material MnO2 nanosheet has been used as the support matrix for the immobilization of horseradish peroxidase （HRP）. HRP entrapped in MnO2 nanosheet film exhibits facile direct electron transfer with the electron transfer rate constant of 6.86 s^-1. The HRP/MnO2 nanosheet film gives a reversible redox couple with the apparent formal peak potential （E^0＇） of -0.315 V （vs. Ag/AgCl） in pH 6.5 phosphate buffer solution （PBS）. The formal potential E^0＇ of HRP shifts linearly with pH with a slope of -53.75 mV.pH^-1, denoting that an electron transfer accompanies single-proton transportation. The immobilized HRP shows an electrocatslytic activity to the reduction of H2O2. The response time of the biosensor for H2O2 is less than 3 s, and the detection limit is 0.21 μmol · L^-1 based on signal/noise = 3.     

TiO2/SiO2复合光催化剂制备工艺参数优化及其表征

先以无机钛盐、硅酸盐为原料制取聚合硅酸硫酸钛,再通过液相水解法制得TiO2/SiO2复合光催化剂,并用SEM、XRD、BET和甲基橙脱色率对复合光催化剂进行表征。结果表明,TiO2/SiO2复合光催化剂制备优化工艺参数为:Ti(SO4)2作钛源、Ti/Si摩尔比为12∶1、水解反应pH值为6、煅烧温度为650℃,以此条件制备的复合光催化剂对甲基橙脱色率可达98.6%以上;TiO2/SiO2复合光催化剂为一种分散均匀的纳米级球形颗粒,其成分为以锐钛矿为主的TiO2,SiO2的复合有效抑制了TiO2晶粒的生长,同时提高了TiO2的热稳定性。     

LaVO4/TiO2在分解甲基橙中的光催化性能研究

光催化剂TiO₂在污水有机物降解中有着巨大优势,但由于对光的利用率过低,需要在TiO₂的基础上进行掺杂来改善其光催化性能。本研究利用稀土镧元素对TiO₂进行了掺杂分别制备了LaVO₄/TiO₂和La(NO₃)₃/TiO₂复合光催化剂,并将它们应用于甲基橙的光催化降解反应,证实了LaVO₄对TiO₂的光催化效果有较明显的增强作用。另外还研究了不同pH条件制备和不同掺杂比例的LaVO₄/TiO₂光催化效果,pH在10.56左右制备出的LaVO₄和掺杂比例为5%的LaVO₄制得的LaVO₄/TiO₂复合光催化剂效果较好。     

Preparation and photocatalytic activity of Cu-doped TiO2/SiO2

Cu²⁺-doped nanostructured TiO₂-coated SiO₂ (TiO₂/SiO₂) particles were prepared by the layer-by-layer assembly technique and their photocatalytic property was studied. TiO₂ colloids were synthesized by the sol-gel method using TiOSO₄ as a precursor. The experimental results showed that TiO₂ nanopowders on the surface of SiO₂ particles were well distributed and compact. The amount of TiO₂ increased with the increase in coating layers. The shell structure appeared to be composed of anatase titania nanocrystals at 550°C. The 2-layer coated TiO₂ particles on the surface showed a higher degradation rate compared with all the different-layer samples. The photocatalytic activity of Cu²⁺-doped TiO₂/SiO₂ was higher than that of undoped TiO₂/SiO₂. The optimum dopant content was about 0.10wt%.     

Performances improvement of eosin Y sensitized solar cells by modifying TiO2 electrode with silane-coupling reagent

Chemical fixing of xanthene dye （eosin Y） on the surface of TiO2 electrode was carried out by modifying the electrode with silane-coupling reagent to obtain stable dye-sensitized TiO2 electrode. Such silane modification can not only evidently enhance the stability of dye-sensitized TiO2 electrode but also improve the energy conversion efficiency of the assembled cells by increasing short-circuit photocurrent （Jsc） and open-circuit photovoltage （Voc）. It was found that the improvements of cell performances differ depending on the composition of the electrolyte. The optimum cell of the cell performance was achieved in the electrolyte with 0.5 mol/L TBAI/0.05 mol/L 12/EC：PC（3：1 w/w）, yielding Jsc of 4.69 mA. cm-2, Voc of 0,595 V, fill factor （FF） of 0.64 and ηof 1,78%, Different spectroscopic techniques including UV-Vis spectra, fluorescence spectra, EIS and dark current measurements were employed to derive reasonable analysis and explanations.     

原位合成CNTs/Cu-Al2O3复合材料的性能研究

对Al的质量分数分别为0.20%,0.35%,0.60%的Cu-Al合金粉末进行内氧化,得到Cu-Al₂O₃粉末。采用化学气相沉积法在Cu-Al₂O₃粉末表面原位生长碳纳米管(carbon nano tubes, CNTs),采用放电等离子烧结工艺成功制备了CNTs/Cu-Al₂O₃复合材料。采用扫描电子显微镜和透射电子显微镜观察了CNTs/Cu-Al₂O₃复合粉末、复合材料断口的形貌。采用显微硬度计、微拉伸试验机、摩擦磨损试验机分别对纯Cu及复合材料的维氏硬度、抗拉强度、摩擦因数进行测试。采用电化学工作站测试复合材料在3.5%NaCl (质量分数)水溶液中的耐腐蚀性能。结果表明,随着Al的质量分数的增加,粉末表面合成的CNTs的数量也增多。Al的质量分数为0.35%时,CNTs/Cu-Al₂O₃复合材料的综合性能最佳,与纯Cu相比,复合材料的抗拉强度和腐蚀电势分别提高了86.4%和43.2%,分别为315 MPa和-0.268 V,摩擦因数降低了53.3%,仅为0.28。     

Preparation of narrow band gap V2O5/TiO2 composite films by micro-arc oxidation

V₂O₅/TiO₂ composite films were prepared on pure titanium substrates via micro-arc oxidation (MAO) in electrolytes consisting of NaVO₃. Their morphology and elements were characterized by scanning electron microscopy (SEM) and energy-dispersive X-ray (EDX) analysis. Phase composition and valence states of species in the films were characterized by X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS). Ultraviolet-visible diffuse reflectance spectra (UV-Vis DRS) were also employed to evaluate the photophysical property of the films. The V₂O₅/TiO₂ composite films show a sheet-like morphology. Not only V₂O₅ phase appears in the films when the NaVO₃ concentration of the electrolyte is higher than 6.10 g/L and is loaded at the surface of anatase, but also V⁴⁺ is incorporated into the crystal lattice of anatase. In comparison with pure TiO₂ films the V₂O₅/TiO₂ composite films exhibit significantly narrow band gap energy. The film prepared in an electrolyte consisting of NaVO₃ with a concentration of 8.54 g/L exhibits the narrowest band gap energy, which is approximately 1.89 eV. The V₂O₅/TiO₂ composite films also have the significantly enhanced visible light photocatalytic activity. The film prepared in an electrolyte consisting of NaVO₃ with a concentration of 8.54 g/L exhibits the best photocatalytic activity and about 93% of rhodamine is degraded after 14 h visible light radiation.     

State of water and its implications for supersaturated structures in Mg(NO3)2 aerosols

One technique based on the difference spectra was developed to study the state of water in supersaturated Mg(NO₃)₂ aerosols. The technique could be derived from the observation that the Raman scattering and infrared absorbance cross sections of molecular vibrations of interest remain practically constant from diluted solutions to supersaturated aerosols. The spectra of solvated water were obtained and primarily related to the first hydration layers of solute molecules in supersaturated Mg(NO₃)₂ aerosols. Based on this investigation, a chain structure was proposed to occur in the supersaturated Mg(NO₃)₂ aerosols at low relative humidities (RHs). Supported by National Natural Science Foundation of China (Grant Nos. 20673010 and 20640420450), “111” Project (Grant No. B07012), and China Postdoctoral Science Foundation (Grant No. 20070410466)     

CdS光化学修饰介孔TiO2及其增强的可见光催化活性

[目的]提高介孔TiO₂材料的光催化活性。[方法]采用蒸发诱导自组装法(EISA),以四氯化钛和钛酸丁酯为钛源,嵌段共聚物P123(EO₂₀PO₇₀EO₂₀)为模板剂,制备介孔TiO₂。用光化学修饰法将CdS掺进介孔TiO₂中,合成对可见光有较好响应的复合材料,并利用X射线衍射(XRD)、透射电镜(TEM)、原子吸收分光光度法(AAS)和光催化等手段对样品进行表征。[结果]XRD和TEM结果表明成功合成有序的六方介孔材料;AAS确定复合材料中Cd的含量为0.96mg/g;光催化于500 W氙灯下以2×10^-5mol/L次甲基蓝(MB)为模型污染物,结果显示CdS/TiO₂复合材料的可见光催化活性明显提高。[结论]光化学修饰法制备的介孔CdS/TiO₂复合材料可增强其可见光催化活性。     

TiO2/SiO2/GQDs双层增透膜的制备及其在太阳能板中的应用

采用溶胶-凝胶法制备了SiO₂ 和TiO₂ 纳米溶胶,采用水热法制备了石墨烯量子点（graphene quantum dots,GQDs）。为进一步提高光伏太阳能板的透光率,设计了一种TiO₂/SiO₂/GQDs双层增透膜结构。探究了薄膜的结构、自清洁性能和增透性能,并进一步讨论了GQDs在增透性中的作用。结果表明,SiO₂-TiO₂/TiO₂-GQDs结构的双层薄膜厚度为120 nm时,太阳能板上的光透过率由未涂敷的85%增加至95%。接触角实验和室外耐环境性能实验测试表明,复合膜层接触角为10°,并具有良好的亲水性和耐环境性能。此外,户外实验结果表明,涂覆该薄膜的太阳能电板发电效率提高6%。由此说明双层增透膜可有效地提高太阳能电池板的光能利用率和使用寿命,可高效地利用太阳能。