半连续铸造Al-15Si合金热压缩变形流变应力行为

采用Gleeble-1500D热模拟机进行高温等温压缩试验,研究了半连续铸造Al-15Si铝合金在变形温度为300~500℃,应变速率为0.001~5 s-1条件下的流变应力行为.结果表明,在试验温度范围内,此合金的流变应力随变形温度的升高,应变速率的降低而降低,说明该合金属于正应变速率敏感性材料;可采用Zener-Hollomon参数双曲正弦形式来描述Al-15Si合金高温塑性变形时的流变应力行为;σ解析表达式中材料常数A,α,n值分别为2.07×1012s-1,0.026 MPa-1,4.61,Al-15Si合金的平均热变形激活能Q为180.96 kJ/mol.     

电热合金Cr20 Ni80的热变形行为及热加工图

为了解决Cr20 Ni80电热合金锻造开裂的问题,在Gleeb-1500D热模拟试验机上对该合金进行热压缩试验,研究变形温度为900~1220℃,应变速率为0.001~10 s-1条件下的热变形行为,并根据动态材料模型建立合金的热加工图.合金的真应力-真应变曲线呈现稳态流变特征,峰值应力随变形温度的降低或应变速率的升高而增加;热变形过程中稳态流变应力可用双曲正弦本构方程来描述,其激活能为371.29 kJ·mol-1.根据热加工图确定了热变形流变失稳区及热变形过程的最佳工艺参数,其加工温度为1050~1200℃,应变速率为0.03~0.08 s-1.优化的热加工工艺在生产中得到验证.     

真空热压烧结CuW30复合材料的热压缩变形特性

采用真空热压烧结法制备了CuW30复合材料,在Gleeble-1500D热模拟机上对该材料进行等温热压缩模拟试验.研究了温度为650~950 ℃、应变速率为0.01~5 s^-1、最大变形量为50%条件下的流变应力行为.结果表明：CuW30复合材料存在明显的动态再结晶特征.材料的稳态流变应力随应变速率的增大而增大,在恒应变速率条件下,合金的真应力水平随温度的升高而降低.热变形过程的流变应力可用双曲正弦本构关系来描述.在给定的变形条件下,计算的热变形激活能为231.150 kJ/mol.根据试验分析,合金的热加工宜在850~950 ℃范围内进行,应变速率为0.01~0.1 s^-1.     

含Sc的Al-Cu-Li合金热压缩变形的流变应力行为和显微组织

采用Gleeble-1500热模拟试验机,在变形温度为380℃~500℃和应变速率为0.001~10 s-1的条件下对含钪铝锂合金的热变形行为进行了研究。结果表明:含钪铝锂合金流变应力随变形温度升高和应变速率的降低而减小。以实验为基础,利用作图法和线性回归方法求解得出各参数数值和流变峰值应力方程,利用该方程预测流变应力值与实验结果吻合较好;该合金在高温压缩变形中,在变形温度大于470℃和应变速率小于0.1 s-1时,合金发生了动态再结晶,且温度越高、应变速率越低,该合金越易发生动态再结晶。在380℃~470℃,0.1~10 s-1条件下,对该合金进行热变形加工较为适宜。     

挤压态CuCr25合金热变形行为及其加工图

在Gleeble-3500D热模拟试验机上,对挤压态CuCr25合金在应变速率为0.01~10s~(-1),变形温度为750~900℃的条件下进行恒温压缩模拟实验.结果表明:挤压态CuCr25合金在热变形过程中流变应力随变形温度升高和应变速率降低而减小;可用双曲正弦模型来描述合金的流变行为,其平均激活能为383.4kJ/mol;基于动态材料模型获得了挤压态CuCr25合金的热加工图,并结合金相显微组织分析得到了该合金在实验参数范围内较优的热加工工艺参数范围:加工温度830~900℃,应变速率为0.01~0.1s-1.     

粗大柱状晶纯镍热变形流变应力行为及加工图

采用Gleeble-3500热模拟机,在变形温度为950~1 150℃、应变速率为0.001~10s-1的条件下,研究了粗大柱状晶粒纯镍的热变形行为和加工图.结果表明:热压缩过程中流变应力随应变速率增大而增大,随变形温度降低而增大.流变应力与应变速率、变形温度之间的关系用Zener-Hollomon参数来描述,热变形激活能为312.4kJ/mol.基于动态材料模型(DMM)热加工图及结合合金相显微组织分析,得到纯镍较优的热加工参数:变形温度为1 060~1 120℃,应变速率为0.03~0.20s-1的蛋形区域.     

Cu-Cr-Zr合金热变形行为

在Gleeble-1500D热模拟试验机上,采用高温等温压缩试验,在变形温度650～850℃、应变速率0.001～10 s^-1和总压缩应变量50%的条件下,对Cu-Cr-Zr合金的流变应力行为进行研究.通过应力-应变曲线和显微组织图分析了合金在不同应变速率、不同应变温度下的变化规律.结果表明：应变速率和变形温度对合金再结晶影响较大,变形温度越高,合金越容易发生动态再结晶;应变速率越小,合金也同样容易发生动态再结晶,并且对应的峰值应力也越小.从流变应力、应变速率和温度的相关性,得出了该合金热压缩变形时的热变形激活能Q和流变应力方程.研究分析Cu-Cr-Zr合金的热加工性能,可为生产实践提供理论指导与借鉴.     

基于Zener-Hollomon参数的MoLa合金本构研究

采用Geeble1500型热模拟试验机对MoLa合金进行等温恒应变速率压缩实验,研究在温度800~1 150℃、应变速率0.001~10 s~(-1)范围内的流变曲线特点及本构方程。结果表明,MoLa合金的流变应力随温度的升高和应变速率的降低而减小,变形机制主要以动态回复软化为主,在应变速率为0.001 s~(-1)时,1 000~1 150℃变形温度下软化现象最为显著,其流变应力随应变的增加而降低;采用双曲正弦函数建立Mo La合金本构方程,其变形激活能为342.68 k J/mol,经过误差分析得出所建立的本构方程的相关系数和相对误差分别为0.9441和7.13%,能够较好地预测该合金的热变形行为。     

AZ61镁合金热压缩流变应力的实验

采用Gleeble-1500型热模拟机,对AZ61镁合金进行高温压缩实验,分析该合金在不同变形温度与应变速率条件下的压缩流变应力.研究AZ61镁合金在热变形时,流变应力与变形温度、应变速率之间的关系,并建立相应的流变应力模型.结果表明,AZ61镁合金在高温压缩变形时,当变形温度一定时,流变应力随应变速率的增大而增大;而当应变速率一定时,流变应力随变形温度的升高而降低.AZ61镁合金的热变形过程均表现出较明显的动态再结晶特征,其流变应力的变化规律主要受加工硬化和再结晶软化两者机制的共同作用.在热变形下,AZ61镁合金峰值流变应力可以用双曲正弦模型来进行较好的描述.     

5083铝合金高温变形行为及加工图

采用Gleeble-3800热模拟机对5083铝合金进行高温等温压缩实验,研究该合金在变形温度为300~500℃、应变速率为0.0l~10.0 s-1条件下的流变行为,建立合金高温变形的本构方程和加工图,采用电子背散射衍射(EBSD)分析变形过程中合金的组织特征。研究结果表明:流变应力随变形温度升高而降低,随应变速率增大而升高;当变形温度为400~500℃时,合金发生动态再结晶;5083铝合金的高温流变行为可用Zener-Hollomon参数描述,该合金在真应变为0.6时的加工图中存在2个失稳区域,其优选的加工条件是变形温度为420~500℃,应变速率为0.01~0.10 s-1。     

Markedness and its Interpretation in Language Use

Language markedness is a common phenomenon in languages, and is reflected from hearing, vision and sense, i.e. the variation in the three aspects such as phonology, morphology and semantics. This paper focuses on the interpretation of markedness in language use following the three perspectives, i.e. pragmatic interpretation, psychological interpretation and cognitive interpretation, with an aim to define the function of markedness.     

Characterization of Ordovician carbonate reservoirs, southeastern Saskatchewan, Canada

The discovery of the prolific Ordovician Red River reservoirs in 1995 in southeastern Saskatchewan was the catalyst for extensive exploration activity which resulted in the discovery of more than 15 new Red River pools. The best yields of Red River production to date have been from dolomite reservoirs. Understanding the processes of dolomitization is, therefore, crucial for the prediction of the connectivity, spatial distribution and heterogeneity of dolomite reservoirs.The Red River reservoirs in the Midale area consist of 3～4 thin dolomitized zones, with a total thickness of about 20 m, which occur at the top of the Yeoman Formation. Two types of replacement dolomite were recognized in the Red River reservoir: dolomitized burrow infills and dolomitized host matrix. The spatial distribution of dolomite suggests that burrowing organisms played an important role in facilitating the fluid flow in the backfilled sediments. This resulted in penecontemporaneous dolomitization of burrow infills by normal seawater. The dolomite in the host matrix is interpreted as having occurred at shallow burial by evaporitic seawater during precipitation of Lake Almar anhydrite that immediately overlies the Yeoman Formation. However, the low δ18O values of dolomited burrow infills (-5.9‰～ -7.8‰, PDB) and matrix dolomites (-6.6‰～ -8.1‰, avg. -7.4‰ PDB) compared to the estimated values for the late Ordovician marine dolomite could be attributed to modification and alteration of dolomite at higher temperatures during deeper burial, which could also be responsible for its 87Sr/86Sr ratios (0.7084～0.7088) that are higher than suggested for the late Ordovician seawaters (0.7078～0.7080). The trace amounts of saddle dolomite cement in the Red River carbonates are probably related to "cannibalization" of earlier replacement dolomite during the chemical compaction.     

A computer generator for randomly layered structures

AcomputergeneratorforrandomlylayeredstructuresYUJia shun1,2,HEZhen hua2(1.TheInstituteofGeologicalandNuclearSciences,NewZealand;2.StateKeyLaboratoryofOilandGasReservoirGeologyandExploitation,ChengduUniversityofTechnology,China)Abstract:Analgorithmisintrod…     

低渗透非均质砂岩油藏启动压力梯度研究

理论推导与室内实验相结合,建立了低渗透非均质砂岩油藏启动压力梯度确定方法。首先借助油藏流场与电场相似的原理,推导了非均质砂岩油藏启动压力梯度计算公式。其次基于稳定流实验方法,建立了非均质砂岩油藏启动压力梯度测试方法。结果表明:低渗透非均质砂岩油藏的启动压力梯度确定遵循两个等效原则。平面非均质油藏的启动压力梯度等于各级渗透率段的启动压力梯度关于长度的加权平均;纵向非均质油藏的启动压力梯度等于各渗透率层的启动压力梯度关于渗透率与渗流面积乘积的加权平均。研究成果可用于有效指导低渗透非均质砂岩油藏的合理井距确定,促进该类油藏的高效开发。     

On Tragic Consciousness In The Works By Ernest Hemingway

As an American modern novelist who were famous in the literary world, Hemingway was not a person who always followed the trend but a sharp observer. At the same time, he was a tragedy maestro, he paid great attention on existence, fate and end-result. The dramatis personae's tragedy of his works was an extreme limit by all means tragedy on the meaning of fearless challenge that failed. The beauty of tragedy was not produced on the destruction of life, but now this kind of value was in the impact activity. They performed for the reader about the tragedy on challenging for the limit and the death.     

海南岛地体及其毗邻陆缘晚中生代—新生代古地磁研究和构造演化

本文叙述了对海南岛及其毗邻大陆边缘白垩纪到第四纪地层岩石进行古地磁研究的全部工作过程。通过分析岩石中剩余磁矢量的磁偏角及磁倾角的变化,提出海南岛白垩纪以来经历的构造演化模式如下:早期伴随顺时针旋转而向南迁移,后期伴随逆时针转动并向北运移。联系该地区及邻区的地质、地球物理资料,对海南岛上述的构造地体运动提出以下认识:北部湾内早期有一拉张作用,主要是该作用使湾内地壳显著伸长减薄,形成北部湾盆地。从而导致了海南岛的早期构造运动,而海南岛后期的构造运动则主要是受南海海底扩张的影响。海南地体运动规律的阐明对于了解北部湾油气盆地的形成演化有重要的理论和实际意义。     

An Index mechanism for multi-scale view in spatial databases

There are numerous geometric objects stored in the spatial databases. An importance function in a spatial database is that users can browse the geometric objects as a map efficiently. Thus the spatial database should display the geometric objects users concern about swiftly onto the display window. This process includes two operations:retrieve data from database and then draw them onto screen. Accordingly, to improve the efficiency, we should try to reduce time of both retrieving object and displaying them. The former can be achieved with the aid of spatial index such as R-tree, the latter require to simplify the objects. Simplification means that objects are shown with sufficient but not with unnecessary detail which depend on the scale of browse. So the major problem is how to retrieve data at different detail level efficiently. This paper introduces the implementation of a multi-scale index in the spatial database SISP (Spatial Information Shared Platform) which is generalized from R-tree. The difference between the generalization and the R-tree lies on two facets: One is that every node and geometric object in the generalization is assigned with a importance value which denote the importance of them, and every vertex in the objects are assigned with a importance value,too. The importance value can be use to decide which data should be retrieve from disk in a query. The other difference is that geometric objects in the generalization are divided into one or more sub-blocks, and vertexes are total ordered by their importance value. With the help of the generalized R-tree, one can easily retrieve data at different detail levels.Some experiments are performed on real-life data to evaluate the performance of solutions that separately use normal spatial index and multi-scale spatial index. The results show that the solution using multi-scale index in SISP is satisfying.     

《Chinese Science Bulletin》SUBJECT INDEX TO VOLUME 59(2014)

正~~     

Achieving Unusual States of Matter Under High Pressure

The elongation method,originally proposed by Imamura was further developed for many years in our group.As a method towards O(N)with high efficiency and high accuracy for any dimensional systems.This treatment designed for one-dimensional(ID)polymers is now available for three-dimensional(3D)systems,but geometry optimization is now possible only for 1D-systems.As an approach toward post-Hartree-Fock,it was also extended to     

Exciton Seebeck in Molecular Systems

Various applications relevant to the exciton dynamics,such as the organic solar cell,the large-area organic light-emitting diodes and the thermoelectricity,are operating under temperature gradient.The potential abnormal behavior of the exicton dynamics driven by the temperature difference may affect the efficiency and performance of the corresponding devices.In the above situations,the exciton dynamics under temperature difference is mixed with