Photoluminescence and cathodoluminescence properties of a novel CaLaGa307：Dy3＋ phosphor

A single host white emitting phosphor, CaLaGa3O7:Dy3+, was synthesized by chemical co-precipitation. Field emission scanning electron microscopy, X-ray diffraction, laser particle size analysis, and photoluminescence and cathodoluminescence spectra were used to investigate the structural and optical properties of the phosphor. The phosphor particles were composed of microspheres with a slight tendency to agglomerate, and an average diameter was of about 1.0 μm. The Dy3+ ions acted as luminescent centers, and substituted La3+ ions in the single crystal lattice of CaLaGa3O7 where they were located in Cs sites. Under excitation with ultraviolet light and a low voltage electron beam, the CaLaGa3O7:Dy3+ phosphor exhibited the characteristic emission of Dy3+ (4F9/2-6H15/2 and 4F9/2-6H13/2 transitions) with intense yellow emission at about 573 nm. The chromaticity coordinates for the phosphor were in the white region. The relevant luminescence mechanisms of the phosphor are investigated. This phosphor may be applied in both field emission displays and white light-emitting diodes.     

Preparation and luminescence characteristics of Sr3SiO5：Eu^2＋ phosphor for white LED

The Sr3SiO5：Eu^2＋ phosphor was synthesized by high temperature solid-state reaction. The emission spectrum of Sr3SiO5：Eu^2＋ shows two bands centered at 487 and 575 nm, which well agree with the theoretic values of emission spectrum. The excitation spectrum for 575 nm emission center has several excitation bands at 365, 418, 458 and 473 nm. And the results show that the emission spectrum of Sr3SiO5：Eu^2＋ is influenced by the Eu^2＋ concentration. The relative emission spectra of the white-emitting InGaN-based YAG：Ce^3＋ LED and Sr3SiO5：Eu^2＋ LED were investigated. The results show that the color development of InGaN-based Sr3SiO5：Eu^2＋ is better than that of InGaN-based YAG：Ce^3＋, and the CIE chromaticity of InGaN-based Sr3SiO5：Eu^2＋ is （x=0.348, y=0.326）.     

Structural investigation and luminescent properties of BaZr(BO<Subscript>3</Subscript>)2:Eu<Superscript>3+</Superscript> phosphors containing Si

Si⁴⁺-doped BaZr(BO₃)₂:Eu³⁺ phosphors are prepared by a conventional solid-state reaction. The influence of Si⁴⁺ addition on the charge transfer state of Eu³⁺-O^2– and photoluminescence (PL) properties of BaZr(BO₃)₂:Eu³⁺ are discussed. Room temperature PL spectra indicated that efficient emission is obtained by Si doping. Increased values for the peak-peak ratio (PPR) of BaZr(BO₃)₂:Eu³⁺ at higher Si doping concentrations implied that the Eu³⁺ ion is located in a more asymmetric environment in BaZr_0.8Si_0.2(BO₃)₂:Eu³⁺ than in the undoped samples. The Judd-Ofelt parameters Ω_λ (λ=2,4) were calculated from the PL data, giving results that were consistent with those from the PPR. The maximum radiative quantum efficiency was achieved at a Si doping concentration of 20 mol%.     

Novel trichromatic phosphor Co-doped with Eu, Tb in SiO2 gel matrix

The Eu, Tb co-doped SiO2 matrix tricolor fluorescence system was prepared by sol-gel technique. Red emission at 618 nm, green emission at 543 nm and blue emission at 350-500 nm were observed in the PL spectra of the sample, indicating that Eu^3＋, Eu^2＋ and Tb^3＋ ions coexisted in the matrix. In the co-doped sample, the blue emission of Eu^2＋ was much stronger than that of the sample single doped with Eu, which implied that the electron transfer between Eu^3＋ and Tb^3＋ maybe happened in the SiO2 matrix. The influences of the annealing temperature and Tb concentration on the PL spectra of the samples were investigated. The optimal doped concentration of Tb was determined to be 0.2% and the optimal annealing temperature 850℃. Annealed at 600℃, Tb^3＋ had a sensitizing effect on Eu^3＋ in the SiO2 matrix, and the emission intensity of Eu^3＋ in the Eu, Tb co-doped sample was more than four times that of the single doped sample, which could be attributed to the energy transfer from Tb^3＋ to Eu^3＋.     

Up-conversion luminescence of Er^3＋ doped and Er^3＋/Yb^3＋ co-doped YTaO4

The synthesis and up-conversion luminescent properties of YTaO4：Er^3＋ and YTaO4：Er^3＋/Yb^3＋ are reported for the first time. According to the measurement results of up-conversion spectra, Yb^3＋ co-doping can remarkably enhance the green （^2H11/2/^4S3/2→^4I15/2） and red （^4F9/2→^4I15/2） emissions, but depress the infrared emission （^4I9/2→^4I15/2）. With the increase of the Yb^3＋ concentration, the intensity of green emission increases, after that, when the Yb^3＋ concentration increases continuously, the intensity of green emission decreases, while those of the red and infrared emissions increase and decrease alternately. In addition, the up-conversion mechanisms of Er^3＋ doped and Er^3＋/Yb^3＋ co-doped YTaO4 are also discussed. It is found that the transform of up-conversion mechanism from two-step energy transfer to cooperating sensitization takes place when Yb^3＋ concentration is increased up to 12 mol%. With the further increase of Yb^3＋ concentration, the energy-back-transfer gradually becomes the dominant up-conversion mechanism, which results in the quenching of the green emission and slight increasing of the red and infrared emissions.     

Near-infrared to visible up-conversion emissions of Er^3＋ doped Al2O3 powders derived from the sol-gel method

The Er3 doped Al2O3 powders were prepared by the sol-gel method using the aluminium isopropoxide [Al(OC3H7)3]-derived Al2O3 sols with addition of the erbium nitrate [Er(NO3)3.5H2O]. The different phase structure, including three crystalline types of (Al,Er)2O3 phases, γ, θ, α, and two Er-Al-O phases, ErAlO3 and Al10Er6O24, was obtained with the 1 mol% Er3 doped Al2O3 powders at the different sintering temperatures of 600―1200℃. The green and red up-conversion emissions centered at about 523, 545 and 660 nm, corresponding respectively to the 2H11/2, 4S3/2→4I15/2 and 4F9/2→4I15/2 transitions of Er3 , were detected by a 978 nm semiconductor laser diodes excitation. The phase structure and OH content had evident influence on the up-conversion emissions intensity. The maximum intensities of both the green and red emissions were obtained respectively for the Er3 doped Al2O3 powders sintered at 1200 ℃, which was composed mainly of α-(Al,Er)2O3, less of ErAlO3 and Al10Er6O24 phases, and with the least OH content. The two-photon absorption up-conversion process was involved in the green and red up-conversion emissions of the Er3 doped Al2O3 powders.     

Effects of Yb^3＋ codoping on visible and near infrared emissions of Er^3＋-Yb^3＋ codoped Al2O3 powders by the sol-gel method

The 0.1 mol% Er^3＋ and 0-2 mol% Yb^3＋ codoped Al2O3 powders were prepared by the sol-gel method, and the phase structure, including only two crystalline types of doped Al2O3 phase, γ-（Al,Er, Yb）2O3 and θ-（Al,Er, Yb）2O3, was detected at the sintering temperature of 1000℃. The visible and near infrared emissions properties depended strongly on the Yb^3＋ codoping, and the corresponding maximal peak intensities centered at about 523, 545, 660 and 1533 nm were obtained respectively for the 0.1 mol% Er^3＋ and 0.5 mol% Yb^3＋ codoped Al2O3 powders, which were composed of θ-（Al,Er,Yb）2O3 and a small amount of γ-（Al,Er, Yb）2O3 phases. The two-photon absorption process was responsible for the visible up-conversion emissions, and the one-photon absorption process was involved in the near infrared emissions of the Er^3＋-yb^3＋ codoped Al2O3 powders.     

Preparation and upconversion luminescence of YVO<Subscript>4</Subscript>:Er<Subscript>3+</Subscript>, Yb<Subscript>3+</Subscript>

YVO₄:Er³⁺, Yb³⁺ with varying Yb³⁺ concentrations were prepared by a precipitation method. The results of X-ray diffraction (XRD) show that all the samples have a tetragonal zircon structure; the calculated average crystallite sizes are in the range of 14–22 nm. The lattice constants and cell volume of the samples decrease slightly with the increase in Yb³⁺ concentration. The upconversion luminescence spectra of all the samples were studied under 980 nm laser excitation. The strong green emission is observed, which is attributed to the ²H_11/2 → ⁴I_15/2 and ⁴S_3/2→⁴I_15/2 transitions of Er³⁺, and the red emission peaks in 650–675 nm can be ignored. The emission intensity for the sample depends on the Yb³⁺ concentration. These results reveal that the upconversion processes of YVO₄:Er³⁺, Yb³⁺ are related to the structure and the doping Yb³⁺ concentration of the sample.     

Synthesis and luminescence properties of Eu3+, Sm3+ doped (YxGd1-x)2O3:Si4+, Mg2+ long-lasting phosphor

A novel red long-lasting phosphor, (Y_1−x Gd _x )₂O₃:Eu³⁺, Sm³⁺, Si⁴⁺, Mg²⁺, was synthesized by the co-precipitation method using oxalate precipitation as the precursor. X-ray diffraction (XRD), scanning electronic microscopy (SEM), integrated thermal analyzer (TG), and photoluminescence spectra (PL) as well as the ST-900PM weak light photometer were used to study the synthesis conditions, morphology, luminescence properties, and the decay time of the phosphor. The XRD results show that the products synthesized at 1400°C for 4 h have good crystallization without any detectable impurity phases. Based on the PL spectra, the optimal conditions are as the following. The molar ratios of Y³⁺ to Gd³⁺ and Eu³⁺ to Sm³⁺ are 2:8 and 3:1, respectively, and the contents of Mg²⁺ and SiO₂ are 5mol% and 3mol%, respectively. The decay time monitored by the ST-900PM weak light photometer is 7200 s, increasing 44% and 100%, respectively, compared with the Eu³⁺ and Sm³⁺ single-doped phosphors. The results indicate that the energy transfer is from Sm³⁺ to Eu³⁺ ion, and Sm³⁺ is a good sensitizer to Eu³⁺.     

Potential red-emitting phosphor GdNbO4:Eu3+,Bi3+ for near-UV white light emitting diodes

A red-emitting phosphor GdNbO₄:Eu³⁺,Bi³⁺ was prepared by a high temperature solid-state reaction technique. The phosphor was characterized by X-ray diffraction (XRD), particle size analyzer and fluorescence spectrometer. The single phase of GdNbO₄:Eu³⁺,Bi³⁺ was obtained at 1150°C and the average particle diameter was about 2.30 ??m. Excitation and emission spectra reveal that the phosphor can be efficiently excited by ultraviolet (UV) light (394 nm) and emit the strong red light of 612 nm due to the Eu³⁺ transition of ⁵D₀??⁷F₂. The optimum content of Eu³⁺ doped in the phosphor GdNbO₄:Eu³⁺ is 20mol%. The phosphor Gd_0.80NbO₄:0.20Eu³⁺,0.03Bi³⁺ shows much stronger photoluminescence intensity and better chromaticity coordinates (x=0.642, 0.352) than GdNbO₄:Eu³⁺. It is confirmed that Gd_0.80NbO₄:0.20Eu³⁺,0.03Bi³⁺ is a potential candidate for near-UV chip-based white light emitting diodes.     

Synthesis and modification of well-ordered layered cathode oxide LiNi<Subscript>2/3</Subscript>Mn<Subscript>1/3</Subscript>O<Subscript>2</Subscript>

Oxalic-acid-based co-precipitation method was employed to prepare LiNi_2/3Mn_1/3O₂ sample with a high-ordered structure. Li⁺, Ni²⁺ and Mn²⁺ acetates were used as starting materials. The influence of the amount of lithium source in the starting materials on Li⁺ content, disorder of Li⁺-Ni²⁺ ions, and electrochemical performance has been investigated. Rietveld refinement shows that the sample prepared with 20% excess Li-source in the starting materials exhibits a perfect ordered structure. A specific discharge capacity is as high as 172 mAh/g at C/20 in the voltage range of 4.35–2.7 V. However, the cyclability is not satisfactory: about 25.3% fade in capacity was observed over 50 cycles. Chemically stable SiO2 was coated on the surface of LiNi_2/3Mn_1/3O₂ particles. A significant improvement in cyclability was attained with 3 wt% SiO2 coating, which is ascribable to the protection of LiNi_2/3Mn_1/3O₂ particles from being dissolved into the electrolyte.     

Thermal degradation of BaAl2Si2O8：Eu2＋ phosphor excited by near ultraviolet light

Eu2+ doped BaAl2Si2O8 phosphor was synthesized by one-step calcination of precursors that were prepared by chemical co-precipitation.The thermal degradation properties of BaAl2Si2O8:Eu2+ were investigated by photoluminescence,lifetime and chromaticity coordinate measurements.BaAl2Si2O8:Eu2+ is efficiently excited by incident light of 250-400 nm,which matches the emission of near ultraviolet LED chips well.BaAl2Si2O8:Eu2+ exhibits broad blue emission at 470 nm because of the 4f65d1-4f7(8S7/2) transition of Eu2+ ions,and the emission band shows an unusual blue shift with bandwidth broadening and emission intensity decreasing as the annealing temperature is increased.The luminescence decay and CIE chromaticity coordinates of BaAl2Si2O8:Eu2+ were determined to investigate its application in white LEDs.     

Synthesis, Characterization and Calorimetry of Ni（C4H8N2O3）2Cl2

A coordination complex was synthesized from NiCl2 and dipeptide glycylglycine（GG）. It was characterized by element analysis, NMR and TG methods, and then was determined to be Ni（C4HsN2O3）2Cl2. Using an isoperibolic reaction calorimeter, the standard molar enthalpy of formation of Ni（GG）2Cl2（solid） has been determined to be -（1 674.66±2.02） kJ · mol^-1 at 298.15 K.     

Luminescent research of Sr5（PO4）3Cl：Eu^2＋ blue phosphor used for electron beam excitation

Eu^2 -aetivated strontium choloro-phosphate has been used for lamp phosphor traditionally with high efficiency. In this paper, the cathodoluminescent properties of Sr5(PO4)3Cl：Eu^2 have been investigated for application in field emission display. The influence of Ba^2 , Ca^2 impurities on the cathodoluminescent spectrum of Sr5(PO4)3Cl:Eu^2 has also been measured. When operate voltage varied from mid- to low-voltage, the relative brightness and saturation behavior of phosphor was observed at different current density.     

Molecular simulation study of the binding mechanism of [α-PTi<Subscript>2</Subscript>W<Subscript>10</Subscript>O<Subscript>40</Subscript>]<Superscript>7−</Superscript> for its promising broad-spectrum inhibitory activity to FluV-A neuraminidase

Polyoxometalate (POM) has promising antiviral activities. It shows broad-spectrum inhibiting ability, high efficiency, and low tox-icity. Experimental assays show that titanium containing polyoxotungstates have anti-influenza-virus activity. In this paper, the bind-ing mechanisms of five isomers of di-Ti-substituted polyoxotungstate, [α-1,2-PTi₂W₁₀O₄₀]^7– (α-1,2), [α-1,6-PTi₂W₁₀O₄₀]^7– (α-1,6), [α-1,5-PTi₂W₁₀O₄₀]^7– (α-1,5), [α-1,4-PTi₂W₁₀O₄₀]^7– (α-1,4) and [α-1,11-PTi₂W₁₀O₄₀]^7– (α-1,11), to five subtypes of influenza virus A neuraminidase (FluV-A NA) were investigated in the context of aqueous solution by using molecular docking and molecular dynamics studies. The results show that the isomer α-1,2 is superior to other isomers as a potential inhibitor to neuraminidase. The positively charged arginine residues around the active site of NA could be induced by negatively charged POM to adapt themselves and could form salt bridge interactions and hydrogen bond interactions with POM. The binding free energies of POM/NA complexes range from –5.36 to –8.31 kcal mol^–1. The electrostatic interactions are found to be the driving force during the binding process of POM to NA. The conformational analysis shows that POM tends to bind primarily with N1 and N8 at the edge of the active pocket, which causes the conformational change of the pincers structure comprising residue 347 and loop 150. Whereas, the active pockets of N2, N9 and N4 are found to be more spacious, which allows POM to enter into the active pockets directly and anchor there firmly. This study shows that negatively charged ligand as POM could induce the reorganization of the active site of NA and highlights POM as a promising inhibitor to NA despite the ever increasing mutants of NA.     

Electrochemical properties of LiNi<Subscript>0.5</Subscript>Mn<Subscript>1.3</Subscript>Ti<Subscript>0.2</Subscript>O<Subscript>4</Subscript>/Li<Subscript>4</Subscript>Ti<Subscript>5</Subscript>O<Subscript>12</Subscript> cells

Spinel compounds LiNi_0.5Mn_1.3Ti_0.2O₄ (LNMTO) and Li₄Ti₅O₁₂ (LTO) were synthesized by different methods. The particle sizes of LNMTO and LTO are 0.5–2 and 0.5–0.8 μm, respectively. The LNMTO/LTO cell exhibits better electrochemical properties at both a low current rate of 0.2C and a high current rate of 1C. When the specific capacity was determined based on the mass of the LNMTO cathode, the LNMTO/LTO cell delivered 137 mA·h·g⁻¹ at 0.2C and 118.2 mA·h·g⁻¹ at 1C, and the corresponding capacity retentions after 30 cycles are 88.5% and 92.4%, respectively.     

Influence of post-annealing on the properties of Ta-doped In<Subscript>2</Subscript>O<Subscript>3</Subscript> transparent conductive films

Ta-doped In₂O₃ transparent conductive oxide films were deposited on glass substrates using radio-frequency (RF) sputtering at 300°C. The influence of post-annealing on the structural, morphologic, electrical and optical properties of the films was investigated using X-ray diffraction, field emission scanning electron microscopy, Hall measurements and optical transmission spectroscopy. The obtained films were polycrystalline with a cubic structure and were preferentially oriented in the (222) crystallographic direction. The lowest resistivity, 5.1×10⁻⁴ Ω cm, was obtained in the film annealed at 500°C, which is half of that of the un-annealed film (9.9×10⁻⁴ Ω cm). The average optical transmittance of the films was over 90%. The optical bandgap was found to decrease with increasing annealing temperature.     

Multi-color long-lasting phosphorescence of rare earth ions in CdSiO<Subscript>3</Subscript> matrix

A series of rare earth ions doped CdSiO3:RE^3 (RE=Y, La, Ce, Pr, Nd, Sm, Eu, Gd, Tb, Dy, Ho,Er, Tin, Yb, Lu) multi-color long-lasting phosphorescence phosphors are prepared by the conventional hightemperature solid-state method. The results of XRD measurement indicate that the products fired under 1050~C for 3h have a good crystallization without any detectable amount of impurity phase. Rare earth ions doped CdSiO3 phosphors possess excellent Inmiuescence properties. When rare earth ions such as Y^3 , La^3 , Gd^3 , Lu^3 , Ce^3 , Nd^3 , Ho^3 , Er^3 ,Tm^3 and Yb^3 are introduced into the CdSiO3 host, one broadband centered at about 420 nm resulting from traps can be observed. In the case of other earth ions such as Pr^3 ,Sm^3 , Eu^3 , Tb^3 and Dy^3 , their characteristic line emitting as well as the -420 nm broadband luminescence can be obtained. The mixture of their characteristic line emitting with the -420 nm broadband Inminescence results in various afterglow color.     

Theoretical investigations of ESR and optical spectra of crystalline KHSO4：Mn^2＋

Calculations of d-d transitions and the axial zero-field splitting parameter D in crystalline KHSO4:Mn2+ have been undertaken, with consideration of the ninth O2– ligand. Energy level values calculated in a tetragonal field are in good agreement with experimentally observed values. Occasionally degenerate energy levels of 4A1(4Eg(G)) and 4A1(4A1g(G)) were found in the tetragonal crystal field. The calculated value of D is in good agreement with experimental value for KHSO4:Mn2+.     

Synthesis and characterization of wormhole-like mesoporous Ce0.6Zr0.35Y0.05O2 solid solutions

Nanoparticles of Ce0.6Zr0.35Y0.05O2 (CZY) solid solution have been prepared by the CTAB (hexadecyl-trimethyl ammonium bromide), CTAB-EG (ethylene glycol) templating, and CTAB-EG-NaCl (in which the pores of the precursor synthesized by the CTAB-EG method is filled by a certain amount of NaCl) method, respectively. The physical properties of these materials were characterized by means of tech-niques such as X-ray diffraction (XRD), high resolution scanning electron microscopy (HRSEM), transmission electron microscopy (TEM), selected area electron diffraction (SAED), and N2 adsorp-tion-desorption measurements. The CZY samples synthesized by the above three methods display wormhole-like mesoporous morphology and cubic crystal structures. The materials are narrow in pore size distribution (averaged pore diameter = 5.3―7.1 nm), high in surface areas (95―119 m2/g), and large in pore volumes (0.16―0.18 cm3/g). It has been demonstrated that the introduction of NaCl is capable of retaining the pore structures of solid nanomaterials at high-temperature calcination.